Emerson Dixell XWEB3000 User manual

QUICK INSTALLATION

GUIDE

(v. 1.1)

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 3/48

WARNING:

This is a class A product. In a domestic environment this product

may cause radio interference in which case the user may be

required to take adequate measures.

WARNING:

Adopt necessary measures to run the system in an environment

free of electromagnetic disturbs. The system is capable to restore

its functionality after a failure due to electromagnetic disturbs if

they do not damage or alter the device.

This product has been developed and implements following

regulations:

EN55022 (Class A); EN55024 (B criteria); EN61000; EN60950.

WARNING:

Use only modems supported by this monitoring unit. Dixell S.r.l.

can accept no responsibility for possible damage due the usage

of not supported modems.

WARNING:

Dixell S.r.l. reserves itself the right to alter this manual without

notice. The last version available can be downloaded from the

website.

WARNING:

Dixell S.r.l. reserves the right to change the composition of its

products, even without notice, ensuring the same and

unchanged functionality.

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 4/48

Contents

1. CHECK LIST.............................................................................................. 5

2. INSTALLATION.......................................................................................... 6

3. MAINTENANCE ......................................................................................... 8

4. RS 485 CONNECTION .............................................................................. 9

The TTL output............................................................................................. 11

Serial address of the instruments.................................................................. 11

5. Local connection with monitor, mouse and keyboard ................................ 12

Windows XP TCP/IP Setup....................................................................... 14

Windows 7 TCP/IP Setup ......................................................................... 17

6. Modem connection (“or point to point connection”).................................... 22

SETTING UP dial-up connection for windows XP...................................... 23

SETTING UP dial-up connection for windows 7 ........................................ 37

7. Intranet / ethernet connection ................................................................... 43

Internet connection....................................................................................... 44

8. Troubleshooting Guide ............................................................................. 46

9. Unit Setup Reminder ................................................................................ 47

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 5/48

1. CHECK LIST

Before installing and configuring the XWEB system we recommend checking

its package to verify it contains:

1 XWEB unit;

1 Quick reference manual (Fast installation);

1 CDROM containing the Operating manual;

1 Power cord for power supply connection;

1 PS2 Splitter for mouse and keyboard;

2 Mounting brackets;

4 Rubber feet and 3 jumpers;

Detachable screw connectors (1x2 ways+1x3 ways; 1x6 ways);

8 Screws, 3,5mm X 6,5mm;

Figure 1

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 6/48

2. INSTALLATION

Do not open XWEB. Its opening makes its warranty invalid. However, to install

XWEB you need:

One blade and one cross screwdrivers

Mouse PS2

Keyboard PS2

Standard VGA screen (no high definition/HDMI)

To install XWEB, please refer to the picture below which represents the back of

XWEB. Apply then following procedure:

1. XWEB has grounding receptacle. Verify the implant in which it will be connected to

adopt electrical ground protection;

2. Fix XWEB at its operating position. In

case of placement on a table insert

provided rubber feet. In case of usage

on rack, use provided brackets and

screws.

3. To connect XWEB to the electrical

network use provided power supply

cable(1). Power supply cable shall

always be easily accessible by an

operator. Do not power the system

on.

4. Connect RS485 network, relays and

digital input (3).

5. Connect to telephonic line network

and/or to LAN (4).

6. Connect keyboard and mouse with

provided cable (5).

7. Connect monitor (5).

8. Connect printer to USB or parallel

receptacles.

9. Connect optional external modem (7).

Its cable shall be maximum 10 meters

long.

10. Power the system on, pressing and

releasing button (2).

Connect XWEB to the electrical network with

provided cord before any servicing operation.

This is for personnel and system safeguard.

Operators shall avoid direct passage of

electronic devices that can cause electric

discharges and damage the device itself;

Power supply voltage shall not differ from the

one required. It can seriously damage the

system;

Mistaken connections can be dangerous and

compromises operators’ safety. Moreover they

can damage the system and/or other connected

instruments.

Adopt one or more external isolator switches to

separate devices to power supply network. They

shall easily accessible.

Do not use XWEB in environments with

inflammable gas.

Do not modify XWEB in any way.

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 7/48

Figure 2

RS485 NETWORK: always use the indicated polarity; total length

shall not exceed 1000m; electric line shall not spit or use star-

connections; avoid proximity of electric power sources; usage of

shielded cable. Its wires shall be 0.5 mm2minimal section. Shield

shall not be connected. Belden 8772 cables are reccomended.

Connect a terminal line resistor (120 Ohm, 1/4 W) on the most

distant device. Resistor shall connect + and – of its serial

connector.

Technical details

Power supply 110 .. 230V ; 0,40A ; 50/60Hz

60W

Temperature/Humidity 0 .. 40°C 20.. 85 % R.H.

Digital outputs (relays) 2 relays 8A 250V N.O.

1 relay 8A 250V double touch

Serial ports 1 RS-232 port

1 RS-485 optoinsuled

USB port 2 standard connection A type ports

Internal modem (if available) Socket modem, PSTN V.34/33.6K

Electrical safeguard normative EN60950

Electromagnetc compatibility normative EN55022; EN55024; EN61000

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 8/48

3. MAINTENANCE

In any case, like maintenance or cleaning or move, XWEB shall not be open.

Warranty expires on opening it. Apply following procedure referencing to XWEB

rear picture introduced in previous paragraph:

1. At first, press and release power on/off button (2);

2. Wait until all frontal LEDs go off including PWR;

3. Disconnect external modem if present (7);

4. Disconnect printer if present (6);

5. Disconnect monitor, keyboard and mouse (5);

6. Disconnect telephonic and/or LAN cables (4);

7. Disconnect RS-485 terminals, relays and digital input (3);

At last, disconnect power cord (1) and handle on XWEB

Keeping pressed power button (2) forces instantaneous

shutdown. XWEB logs such event but can potentially not

operate correctly with other data. Same effects are applied to

the cases in which power cord is removed or power supply

goes off.

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 9/48

4. RS 485 CONNECTION

The cable must have 2 or 3 wires with shield, minimum section 0,5mm2(ex.

BELDEN 8772). From the XWEB position the cable reaches all the instrument

positions. Do not execute loops or derivations.

1592010860 XWEB5000 stp GB r1.1 2012.06.22.doc XWEB5000 10/48

Right connection:

Figure 3

Wrong connection:

Figure 4

Always keep the serial cable away from power cables.

Always keep the serial cable away from Electro-magnetic or frequency sources.

Do not connect shield to ground.

Do not connect the “Gnd (ground)” terminal.

Remember to draw a map of the line. This will help you to find errors if something

is wrong.

The instrument with RS485 have “+” and “-“ terminals, respect the polarity.

To keep the line balanced it is necessary a 100 Ohm resistor at the end of the line

(you ca use the RS 485+ and RS 485- terminals of the last instrument

connected).

Table of contents

Other Emerson Measuring Instrument manuals

Emerson

Emerson Daniel 3410 Series Programming manual

Emerson

Emerson Rosemount 8600D Series User manual

Emerson

Emerson Micro Motion TA Series User manual

Emerson

Emerson Micro Motion 7829 Visconic Series Operational manual

Emerson

Emerson Micro Motion FDM User manual

Emerson

Emerson PENBERTHY H Series Manual

Emerson

Emerson Rosemount Oxymitter DR User manual

Emerson

Emerson Rosemount FCL Series User manual

Emerson

Emerson Rosemount Analytical RDO User manual

Emerson

Emerson Rosemount X-Stream Series Installation and operating instructions

Emerson

Emerson Rosemount 2410 User manual

Emerson

Emerson Rosemount WPG User manual

Emerson

Emerson Nelson CM-1 User manual

Emerson

Emerson Daniel 3410 Series User manual

Emerson

Emerson A6312 User manual

Emerson

Emerson Micro Motion LNG Series Quick guide

Emerson

Emerson DIXELL XWEB1000D PRO Wiring diagram

Emerson

Emerson ROSEMOUNT NGA2000 HFID User manual

Emerson

Emerson World Class 3000 User manual

Emerson

Emerson Rosemount 8800D Series User manual

Emerson

Emerson Daniel Series User manual

Emerson

Emerson Rosemount 2051CF series User manual

Emerson

Emerson Rosemount 8750W User manual

Emerson

Emerson RLDS Operating instructions

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual