DT Research WebDT 312 User manual
WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile Tablet
Barcode Scanner
Installation
The Barcode Scanner is preinstalled as an option for WebDT 312/ 362.
Button Management
To assign Scanner Trigger button, follow the procedures below.
1. Start Button Manager by clicking on in the system tray.
2. Click on to go to the second screen of Button Manager.
3. Select an available unused button marked with the icon .
4. Click on the icon to assign the Scanner Trigger to the
unused button.
5. Click OK to apply conguration settings and close the
window.
Scanner Conguration
To Add/Remove Symbologies, follow the procedures below.
1. Click Start | All Programs | DT Research | Button Manager | ScannerCong.
2. Select COM3 and click Connect button.
3. Add Symbology with button and Remove Symbology with button.
4. Select the Beep after scanning barcode checkbox to enable beep sound after
scanning bar code or deselect it to disable the beep sound.
5. Click OK to apply the conguration settings and close the window.
To Connect Barcode Scanner Module
To connect the Barcode Scanner, you can use the
WebDT Keyboard Wedge to connect. Tap on the
icon in the task bar, a menu displayed as shown in
the picture below. Select Connect Scanner.
To Test Barcode Scanner Module
Click1. Start | All Programs | Accessories | Notepad to run the Notepad
Scan one of the several supported barcode Symbology. The output will appear in2.
the Notepad screen.
Verify the captured data.3.
OPERATION GUIDE
www.dtresearch.com
WebDT Mobile Tablet Barcode Scanner Operation Guide
The Default Port Parameters for Barcode Scanner Module
SPECIFICATIONS
Electrical
Characteristics
Voltage 3.3V+/- 5%
Current 370mA @3.3V scanning with power save
Idle 40mA
Standby current 3mA
Environment
Ambient light Works in any lighting conditions,
from 0 to 100,000 lux
Shock 2000G, 0.7ms, half sinus, 3 axes
Vibration 8G r.m.s., from 10Hz to 500Hz,
2 hours/axis, 3 axes
Interfaces High speed RS232 TTL with Intermec Scanner Control Protocol (ISCP)
Physical
Characteristics
Scan engine
(H x W x D)
12.4 x 20.9 mm x 14.0 mm;
0.5 x 0.8 x 0.55 in
Decode board
(H x W x D)
6.6 x 38.1 x 25.4 mm;
0.25 x 1.5 x 1 in
Decoded 2D module
(H x W x D)
16 x 38.1 x 26.8 mm;
0.6 x 1.5 x 1.05 in
Weight 10g (0.35 oz.)
Scanning
Performance
Scan Rate
2D mode: 56 images/s auto adaptive
Linear emulation mode: 200 scans/s auto
adaptive
Scan angle 38.9° (Horizontal), 25.4°(Vertical)
Optical resolution 752 (H) x 480 (V) pixels, 256 gray levels
Print Contrast down to 25%
Versions Standard range and high density
Note: Specications are subject to change without notice.
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com
Copyright © 2009, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
Linear Imager Compliance and Precaution
This product complies with the following standards for laser and LED safety.
IEC 60825-1 / EN 60825-1 - Class 1 LED Product
Port COM3
Baud Rate 57600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile Tablet
CMOS Camera
OPERATION GUIDE
www.dtresearch.com
Installation
The CMOS Camera is preinstalled as an option for WebDT 312/ 362.
To Test CMOS Camera Module
To test the CMOS Camera, launch Microsoft® Paint from Start | All Programs
| Accessories. Select File | From Scanner or Camera to initiate the Capture
Pictures from Video window.
Click Settings to
decide properties of
captured pictures.
Click on Capture
button or pre-assigned
trigger button to take
a picture.
Select a captured
picture on right
column, click Get
Picture to export the
picture to Paint or click
Delete to delete the
picture.
4
4
4
Button Management
To assign Camera Trigger button, follow the procedures below.
1. Start Button Manager by clicking on in the system tray.
2. Click on to go to the second screen of Button
Manager.
3. Select an available unused button marked with the icon .
4. Click on the icon to assign the Camera Trigger to the
unused button.
5. Click OK to apply conguration settings and close the window.
WebDT Mobile Tablet Barcode Scanner Operation Guide
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com
Copyright © 2009, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
SPECIFICATIONS
Sensor UXGA resolution image sensor
Resolution 640 x 480 (default),
1280 x 1024, 1600 x 1200, 2048 x 1536
LED indicator Yes
Auto focus Yes
Automatic image control Automatic Exposure Control
Automatic white Balance Control
Focusing type Auto Focus
Focus Distance Focal on 60cm
Interface High speed USB 2.0
Regulatory RoHS compliant
Note: Specications are subject to change without notice.
WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile Tablet
Magnetic Stripe Reader
OPERATION GUIDE
www.dtresearch.com
Installation
The Magnetic Stripe Reader (MSR) is preinstalled as an
option for WebDT 312/ 362.
To Connect Magnetic Stripe Reader Module
To connect the Magnetic Stripe Reader,
you can use the WebDT Keyboard Wedge.
Tap on the icon in the task bar, a menu
is displayed as shown in the picture below.
Choose Connect MSR.
To Congure MSR
For a magnetic stripe card, the raw data in each data track may contain start
and end sentinel characters. To remove those characters, you can select the
Congure MSR command to parse input raw data and lter out the start and end
sentinel characters on each track.
Click Cong MSR in the WebDT 1.
Keyboard Wedge menu, and the MSR
Application Conguration window will
be displayed.
Choose Enable in the Parse Data2.
section.
Choose data you want to parse at the
start or end of each track.
For Example:
Check Track 1
In Start Sentinel Character, select• %
In End Sentinel Character, select• ?
Click OK to complete the settings3.
WebDT Mobile Tablet Barcode Scanner Operation Guide
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com
Copyright © 2009, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
To Test Magnetic Stripe Reader Module
Click1. Start | All Programs | Accessories | Notepad to run the Notepad.
Swipe a magnetic stripe card across the module. The output will appear in the2.
Notepad screen.
Verify the captured data.3.
Default Port Parameters for Magnetic Stripe Reader Module
SPECIFICATIONS
Reference Standards
ANSI/ISO 7810, 7811-1/6, 7813-
JIS X6301, X6302-
AAMVA-
Recording Method Two frequency coherent phase (F2F)
Decoding Method ISO Track1: IATA, Track2: ABA, Track3: THRIFT
Card Swiping direction Bi-directional
Status Indicator Card Swiping Speed 7 cm/s ~ 250 cm/s
Mechanical Dimensions (L x W x H) 98.3 x 30.3 x 31.2 mm, with
cover
Power Power Requirements 5 VDC +/- 10%; Power
supplied by keyboard or USB interface
Life Electronics 125,000 hours
Head 1,000,000 passes
Note: Specications are subject to change without notice.
Port COM3
Baud Rate 57600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
This manual suits for next models
1
Table of contents
Other DT Research Tablet manuals
DT Research
DT Research DT362 Assembly instructions
DT Research
DT Research DT382GL Assembly instructions
DT Research
DT Research DT301C Assembly instructions
DT Research
DT Research DT301XC Assembly instructions
DT Research
DT Research DT311H Assembly instructions
DT Research
DT Research DT318CR Assembly instructions
DT Research
DT Research 302MD Assembly instructions
DT Research
DT Research DT317BT Assembly instructions
DT Research
DT Research DT390 Assembly instructions
DT Research
DT Research 507T Assembly instructions
DT Research
DT Research DT315BT Assembly instructions
DT Research
DT Research DT301Q Assembly instructions
DT Research
DT Research DT340T Assembly instructions
DT Research
DT Research 524T Assembly instructions
DT Research
DT Research DT313H Assembly instructions
DT Research
DT Research DT363GL Assembly instructions
DT Research
DT Research DT365 Assembly instructions
DT Research
DT Research DT395BV Assembly instructions
DT Research
DT Research DT302P Assembly instructions
DT Research
DT Research DT311 Assembly instructions
Popular Tablet manuals by other brands
Laser
Laser MID-1060 Quick operation guide
MUNBYN
MUNBYN IRT09J Easy setup guide
Motorola
Motorola MC3090R - Win CE 5.0 Professional 520 MHz quick start guide
Dell
Dell Latitude ST Setup and features information
Lenovo
Lenovo IdeaTab S6000L Hardware Maintenance Manual
Venturer
Venturer WT9L11 quick start guide
