Dimplex EF3003-230 User manual

PRACTICAL USER’S GUIDE

FOR THE ELECTRIC FIREPLACE

MODEL NUMBER:

EF3003-230

Valued Customer,

We are pleased that you have chosen to purchase an electric

fireplace manufactured by Dimplex North America Ltd.

Over the years, valuable memories ill occur around the

armth and comfort of your hearth. Thank you for allo ing our

product to be the backdrop for those special moments.

7206700100REV02

Quality checked by:

CONTENTS

PAGE 1 Important Instructions

PAGE 2 Model and Serial Number

Information

PAGE 3 Site selection and preparation

PAGE 5 Fireplace Installation

PAGE 6 Operation

PAGE 9 Maintenance

PAGE 12 Warranty

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC

FIREPLACE

1. Prior to the first use of the fireplace verify the following:

• Are the circuit breakers for the unit on?

• Are the light bulbs in your fireplace loose? (to check, follow the

instructions for replacing the light bulbs under the maintenance

section of this manual)

2. The heater on your fireplace may emit a slight, harmless odor when

first used. This odor is a normal condition caused by the initial

heating of internal heater parts and will not occur again.

3. If your heater does not emit heat, ensure the switch is on and the

thermostat is turned fully clockwise. If this does not work, switch the

unit off for 5 minutes and try again. Consult page 5 of your Practical

User’s Guide for further information.

IMPORTANT INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,

electric shock, and injury to persons, including the following:

1. Read all instructions before using the electric fireplace.

2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. The trim around the heater outlet becomes hot during heater operation. Keep

combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3

feet (0.9m) from the front of the unit.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever

the unit is left operating and unattended.

4. Young children should be supervised to ensure that they do not play with the appliance.

5. The appliance is not intended for use by young children or infirmed persons without supervision.

6. The appliance must be positioned so that the plug is accessible.

7. Always unplug the electric fireplace when not in use.

8. If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent, or a

qualified person in order to avoid a hazard.

9. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the

electric fireplace has been dropped or damaged in any manner. Return heater to authorized service

facility for examination, electrical or mechanical adjustment, or repair.

10. Do not use outdoors.

11. Do not use this fireplace in the immediate surroundings of a bath, a shower or a swimming pool.

12. Do not install the fireplace directly on carpet or a similar surface which may restrict air circulation

beneath the unit.

13. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like.

Arrange cord away from traffic area and where it will not be tripped over.

14. Do not locate the heater immediately below a fixed socket-outlet.

15. To disconnect the fireplace, turn the controls off, then remove the plug from the outlet.

16. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause

an electric shock or fire, or damage to the heater.

17. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft

surfaces, like a bed, where openings may become blocked.

18. All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where

gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to

flammable vapors.

19. Do not modify the electric fireplace. Use it only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock or injury to persons.

20. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you

must use an extension cord, the cord must be 3-core type and have a rating no less than 13 amps.

21. Do not burn wood or other materials in the electric fireplace.

22. Do not strike the fireplace glass.

23. Always use a certified electrician should new circuits or outlets be required.

24. Always use properly grounded, fused and polarized outlets.

25. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.

26. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration

and store so as to avoid damage.

NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to the

equipment.

WARNING: Procedures and techniques, which, if not carefully followed, will expose the user to the risk of

fire, serious injury, illness or death.

Model Number

Serial Number

IMPORTANT INSTRUCTIONS

If you have any questions about our products please have the product model and serial

numbers available upon calling Dimplex customer service. To locate the model and serial

number labels see below.

Firebox Carton

SITE SELECTION AND PREPARATION

This section provides easy step by step instructions for selecting a location and preparing the

site to install the fireplace into:

• Existing Fireplace

• New wall construction

• Dimplex mantel surround kit or custom made mantel surround

NOTE

The fireplace insert comes completely assembled and

wired. Some tools may be required to prepare the

site and assembly/install the trim.

The dimensions of the fireplace insert are 762mm

wide X 641mm high X 286mm deep. (FIGURE 1)

You should allow 6mm around the fireplace insert for

ease of installation.

This fireplace does not require any venting.

CAUTION

Clearance for air circulation beneath the fireplace insert is

provided by three rubber feet (FIGURE 1).

DO NOT INSTALL THE FIREPLACE INSERT

DIRECTLY ON CARPET OR SIMILAR SURFACES

WHICH MAY RESTRICT AIR CIRCULATION. If

installing the fireplace in a carpeted area, place a

one-piece, solid, flat surface under the fireplace

insert. Ensure that all three of the insert’s feet rest

securely on this surface.

EXISTING FIREPLACE INSTALLATION

1. Seal all drafts and vents with non-fibrous

insulation materials to prevent chimney debris

from falling into the fireplace insert. Do not

install into an existing fireplace that is prone to

leaks or dampness.

2. Cap the top of the chimney flue to prevent rain

from entering.

3. Plan your electrical power supply: (refer to

NOTE 1)

4. The power cord can run along the front of the

hearth to an outlet near the fireplace

(FIGURE 2).

FIGURE 1

FIGURE 2

762mm

641mm

286mm

NOTE

The fireplace insert must be installed on a hard

surface.

NOTE

A 13 AMP, 230 VOLT (240V in Australia) circuit is

required. A dedicated circuit is preferred but not

essential in all cases. A dedicated circuit will be

required if, after installation, the circuit breaker trips or

fuse blows on a regular basis when the heater is

operating. Additional appliances on the same circuit

may exceed the current rating of the circuit breaker.

WARNING

To prevent personal injury you should hire a

professional to cap the chimney flue or cut a hole in

the existing fireplace for wiring.

If you return your existing fireplace to its original use

(Example wood burning), it should be inspected by

the local building department prior to use to reduce

the risk of fire and personal injury.

NEW WALL CONSTRUCTION

1. Select a suitable location that is not susceptible to

moisture and is away from drapes, furniture and

high traffic.

2. Place the fireplace in the desired location to see

how it will look in the room.

3. Mark the desired location on the floor and store

the fireplace in a safe, dry and dust free location.

4. Use studs to frame an opening of 775mm wide X

654mm high X 305mm deep.

5. Plan your electrical power supply.

(refer to NOTE 1)

Option #1 - The power cord can be lead from behind

the trim and along the wall to an outlet near the

fireplace. (FIGURE 4)

Option #2 - A new outlet can be installed inside the

new frame construction. (if allowed by electrical

code). (FIGURE 5)

FIGURE 3

FIGURE 5

FIGURE 4

305mm

775mm

654mm

WARNING

Construction and Electrical Outlet wiring must

comply with local building codes and other

applicable regulations to reduce the risk of fire,

electrical shock and injury to persons.

WARNING

Do not attempt to wire your own new outlets or

circuits. To reduce the risk of fire, electric shock or

injury to persons, always use a licensed electrician.

MANTEL SURROUND KIT OR CUSTOM MADE

MANTEL SURROUND

1. Select a suitable location that is not susceptible to

moisture and is away from drapes, furniture and

high traffic.

2. Place the fireplace in the desired location to see

how it will look in the room.

3. For ease of electrical hook up you may wish to

locate the fireplace near an existing outlet. (refer

to NOTE 1)

4. Store the fireplace in a safe dry and dust free

location.

5. Assemble the mantel surround kit (refer to the

mantel assembly instructions) or construct the

custom surround with an opening of 775mm X

654mm X 305mm.

FIREPLACE INSERT INSTALLATION

This section provides easy step by step instructions for installation of your fireplace.

1. Install Trim Kit to front of fireplace by positioning

trim then pushing straight forward against the

fireplace.

2. Make sure the unit is switched OFF (Refer to

operating instruction section).

3. Plug the fireplace into a 13AMP/230Volt (240V in

Australia) outlet. If the cord does not reach you

may use a 3-core type extension cord rated for a

minimum of 13 AMPS.

4. Push the Fireplace into place so that the trim is

against the finished Mantel Surround or wall

surface. (FIGURE 6)

5. Level, if required with wood shims (not included)

(FIGURE 7).

FIGURE 7

FIGURE 6

OPERATION

This section will explain the function of each convenient control.

1. To access the controls, open the upper grill by pulling, near the top right hand side,

forward and down. (FIGURE 9)

2. To locate controls refer to FIGURE 10.

3. To conceal the controls during the operation, return the grill to its original upright

position.

WARNING

Ensure the power cord is not installed so that it is

pinched or against a sharp edge and ensure that

the power cord is stored or secured to avoid

tripping or snagging to reduce the risk of fire,

electric shock or injury to persons.

FIGURE 8

WARNING

The centre and left hand side of the grille will get

hot when the heater is operating. Take care to

always grasp the grille on the right hand side.

FIGURE 9

CAUTION

If you need to continuously reset the heater, unplug

the unit and call your local

dealer.

A. MAIN ON/OFF SWITCH

The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame).

B. MAIN POWER INDICATOR LIGHT

The main power indicator light will illuminate, confirming the unit is turned ON.

C. FLAME ACTION CONTROL

Turn the flame action control knob to adjust the flame speed to the desired level.

D. FLAME BRIGHTNESS CONTROL

Turn the flame brightness control knob to increase or decrease the brightness of the flame

and embers.

E. LED INDICATORS

Indicates the current function of the fireplace

F. MANUAL SELECTION BUTTONS

To choose between flame effect setting, flame effect with low heat setting, and flame effect

with high heat setting.

G. HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements, turn the thermostat control

clockwise all the way to turn on the heater. When the room reached the desired

temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in

this position to maintain the room temperature at this setting. For additional heat, turn

clockwise until you hear the click again and the heater will turn on.

NOTE:

The heater may emit a slight, harmless odor when first used. This odor is a normal condition

caused by initial heating of internal heater parts and will not occur again.

RESETTING THE TEMPERATURE CUTOFF SWITCH

This unit is equipped with a thermostat, which controls the temperature of the room. It does

this by turning the heater on and off. The heater is protected with a safety device to prevent

overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will

not come back on without being reset. It can be reset by switching the main ON/OFF SWITCH

to OFF and waiting 5 minutes before switching the unit back on.

CAUTION

If you need to continuously reset the heater, unplug the unit and call your local dealer.

FIGURE 10

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex Revillusion RBF30C-AU User manual

Dimplex

Dimplex DF2024 User manual

Dimplex

Dimplex MULTI-FIRE SL PLF3614-XS User manual

Dimplex

Dimplex VCX1525-EU User manual

Dimplex

Dimplex SP420 User manual

Dimplex

Dimplex BLF34 User manual

Dimplex

Dimplex DWF3651 User manual

Dimplex

Dimplex ELECTRALOG CFP3913 User manual

Dimplex

Dimplex ELGAR EGR20 User manual

Dimplex

Dimplex Purifire BF series User manual

Dimplex

Dimplex DF2608 User manual

Dimplex

Dimplex LKD20-AU User manual

Dimplex

Dimplex ADG20BN User guide

Dimplex

Dimplex 6911540100 User manual

Dimplex

Dimplex Revillusion SWD20-AU User manual

Dimplex

Dimplex Revillusion RBF30WC User manual

Dimplex

Dimplex DWF-1326 User manual

Dimplex

Dimplex DFI2310 User manual

Dimplex

Dimplex Opti-V PGF10 User manual

Dimplex

Dimplex BF33ST User manual

Dimplex

Dimplex XHD23G User manual

Dimplex

Dimplex ENG56-400 User manual

Dimplex

Dimplex DFG3033 User manual

Dimplex

Dimplex SS5800PB User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual