Dimplex DIMPLEX ELECTRIC FIREPLACE User manual

PRACTICAL USER’S GUIDE

FOR THE

DIMPLEX ELECTRIC FIREPLACE

Valued Customer,

We are pleased that you have chosen to purchase an electric fireplace

manufactured by Dimplex North America Ltd.

Over the years, valuable memories will occur around the warmth and comfort

of your hearth. Thank you for allowing our product to be the backdrop for

those special moments. 7206960100REV04

www.sylvane.com 1-800-934-9194

CONTENTS

PAGE 1 Important Instructions

PAGE 3 Site selection and preparation

PAGE 4 Installation

PAGE 5 Operation

PAGE 5 Remote Control

PAGE 7 Maintenance

PAGE 10 Warranty

www.sylvane.com 1-800-934-9194

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC

FIREPLACE

1. Prior to the first use of the fireplace verify the following:

• Are the circuit breakers for the fireplace on?

• Are the light bulbs in your fireplace loose? (to check, follow the

instructions for replacing the light bulbs under the maintenance

section of this manual)

2. The heater on your fireplace may emit a slight, harmless odor when

first used. This odor is a normal condition caused by the initial

heating of internal heater parts.

3. The information regarding the model of your fireplace can be found

on the rating plate located on the top or the back of the fireplace.

4. If you have any technical questions regarding the operation of your

fireplace, or require service for your fireplace contact Dimplex North

America customer service at 1-888-DIMPLEX (1-888-346-7539).

www.sylvane.com 1-800-934-9194

IMPORTANT INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this fireplace.

2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The

trim around the heater outlet becomes hot during heater operation. Keep combustible

materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m)

from the front of the unit.

3. Extreme caution is necessary when any heater is used by or near children or invalids and

whenever the fireplace is left operating and unattended.

4. Always unplug the fireplace when not in use.

5. Do not operate any fireplace with a damaged cord, plug, or if the heater has malfunctioned, the

fireplace has been dropped or damaged in any manner.

6. Do not use outdoors.

7. This fireplace is not intended for use in bathrooms, laundry areas and similar indoor locations.

8. Do not install the fireplace directly on carpet or a similar surface, which may restrict air

circulation beneath the unit.

9. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like.

Arrange cord away from traffic area and where it will not be tripped over.

10. To disconnect the fireplace, turn the controls off, then remove the plug from the outlet.

11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may

cause an electric shock or fire, or damage to the heater.

12. To prevent a possible fire, do not block air intake or exhaust in any manner.

13. All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where

gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to

flammable vapors.

14. Do not modify this fireplace. Use it only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock or injury to persons.

15. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper

outlet. Do not change the plug in any way.

Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If

you must use an extension cord, the cord must be No. 16 AWG minimum size and rated no less

than 1875 watts.

16. Do not burn wood or other materials in this fireplace.

17. Do not strike fireplace glass.

18. Always use a certified electrician should new circuits or outlets be required.

19. Always use properly grounded, fused and polarized outlets.

20. Disconnect all power supply before performing any cleaning, maintenance or relocation of the

fireplace.

21. When transporting or storing the fireplace and cord, keep in a dry place, free from excessive

vibration and store so as to avoid damage.

NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage

to the equipment.

WARNING: Procedures and techniques, which, if not carefully followed, will expose the user

to the risk of fire, serious injury, illness or death.

SAVE THESE INSTRUCTIONS 1

www.sylvane.com 1-800-934-9194

Catalogue Number

Serial Number

IMPORTANT INSTRUCTIONS

If you have any questions about our products please have the product catalogue and serial

numbers available upon calling Dimplex customer service. To locate the catalogue and serial

number labels see below.

Firebox

Catalogue Number Serial Number

www.sylvane.com 1-800-934-9194

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all

cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse

blows on a regular basis when the heater is operating. Additional appliances on the same

circuit may exceed the current rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure

that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire,

electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of fire, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

SITE SELECTION AND PREPARATION

This section provides easy step-by- step instructions for selecting a location and preparing the

site to install the fireplace into:

• Existing Fireplace

• New wall construction

• Dimplex mantel surround kit or custom made mantel surround

Option #1-The power cord can be lead from behind the fireplace trim and along the wall to an

outlet near the fireplace.

Option #2-A new outlet can be installed inside the new frame construction.

Option #3-The power cord can be lead from behind the mantel and along the wall to an outlet

near the fireplace.

NOTE

The fireplace insert comes completely assembled and wired.

Some dimensions of the fireplace insert are shown on Fig. 1.

WARNING: The fireplace insert is to be installed in an opening with minimum

dimensions: 24” wide by 23” high and 11.5” deep.

CAUTION

Clearance for air circulation beneath the fireplace insert is provided by four rubber feet (Figure 1).

DO NOT INSTALL THE FIREPLACE INSERT DIRECTLY ON CARPET OR SIMILAR

SURFACES WHICH MAY RESTRICT AIR CIRCULATION. If installing the fireplace in a

carpeted area, place a one-piece, solid, flat surface under the fireplace insert. Ensure that all

four of the insert’s feet rest securely on this surface. 3

Figure 1

www.sylvane.com 1-800-934-9194

EXISTING FIREPLACE INSTALLATION

1. Seal all drafts and vents with non-fibrous insulation materials to prevent chimney debris

from falling into the fireplace insert. Do not install into an existing fireplace that is prone

to leaks or dampness.

2. Cap the top of the chimney flue to prevent rain from entering.

3. Plan your electrical power supply: (refer to NOTE 1)

4. The power cord can run along the front of the hearth to an outlet near the fireplace

NOTE 1

A 15 AMP, 120 VOLT circuit is required. A dedicated circuit is preferred but not essential in

all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or

fuse blows on a regular basis when the heater is operating. Additional appliances on the

same circuit may exceed the current rating of the circuit breaker.

WARNING

To prevent personal injury you should hire a professional to cap the chimney flue or cut a

hole in the existing fireplace for wiring.

If you return your existing fireplace to its original use (Example wood burning), it should be

inspected by the local building department prior to use to reduce the risk of fire and

personal injury.

NEW WALL CONSTRUCTION

1. Select a suitable location that is not susceptible to moisture and is away from drapes,

furniture and high traffic.

2. Place the fireplace in the desired location to see how it will look in the room.

3. Mark the desired location on the floor and store the fireplace in a safe, dry and dust free

location.

4. Use studs to frame an opening of 24” wide X 23 ¼” high X 11 ½” deep.

5. Plan your electrical power supply (refer to NOTE 1)

DIMPLEX MANTEL SURROUND KIT OR CUSTOM MADE MANTEL SURROUND

1. Select a suitable location that is not susceptible to moisture and is away from

drapes, furniture and high traffic.

2. Place the fireplace in the desired location to see how it will look in the room.

3. For ease of electrical hook up you may wish to locate the fireplace near an existing

outlet. (refer to NOTE 1)

4. Store the fireplace in a safe dry and dust free location.

5. Assemble the mantel surround kit (refer to the mantel assembly instructions) or

construct the custom surround with an opening of 24” wide X 23 ¼” high X 11 ½”

deep.

WARNING

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

www.sylvane.com 1-800-934-9194

FIREPLACE INSERT INSTALLATION

1. Make sure the units MAIN ON/OFF switch is switched OFF (refer to operating

instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you may use an

extension cord rated for a minimum of 1875 watts.

3. Push the fireplace into the opening being careful not to damage the base of the mantel

or cabinet so that the fireplace is flush with the mantel or cabinet.

4. Level the unit with shims if necessary (not provided).

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and

ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the

risk of fire, electric shock or injury to persons.

OPERATION

The fireplace is supplied with an integrated on/off

remote control.

Note: Ensure that the fireplace 3 position switch is set to

the remote control setting.

To operate, push the ON button to turn fireplace on, push the

OFF button to turn the fireplace off.

BATTERY REPLACEMENT

To replace the battery, slide battery cover open on the hand

held transmitter.

Correctly install one 12 volt (A23) battery in the battery holder.

Close the batter cover.

Resetting the temperature cutoff switch

The heater is protected with a safety device to prevent overheating. Should the heater

overheat, an automatic cut out will turn the heater off and it will not come back on without

being reset. It can be reset by switching the ON/OFF SWITCH to OFF and waiting 5

minutes before switching the unit back on.

Caution

If you need to continuously reset the heater, unplug the unit and call your local dealer.

REMOTE

CONTROL

MANUAL

OPERATION

MAIN THREE

POSITION ON

OFF SWITCH

THERMOSTAT

HEAT

SWITCH

OFF

ON BUTTON OFF BUTTON

BATTERY

COVER

BATTERY

www.sylvane.com 1-800-934-9194

Three position ON/OFF switch

The switch has two ON positions marked with “-“ and “=”.

The “-“ position is for manual operation.

In this position the built-in remote control is bypassed.

The “=” position is for operating the unit with the provided remote control.

When in “=” position the unit is operated with the ON and OFF buttons of the remote

control.

When the switch is in the center position the unit is off.

Heat switch

The HEAT ON/OFF SWITCH supplies power to the heater fan and the heater element.

When the switch is in the ON position the heater operates if the thermostat calls for heat.

Heater thermostat control

To adjust the temperature to your individual requirements, turn the thermostat control

clockwise all the way to turn on the heater. When the room reaches the desired

temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in

this position to maintain the room temperature at this setting. For additional heat, turn

clockwise until you hear the click again and the heater will turn on.

www.sylvane.com 1-800-934-9194

MAINTENANCE

Light Bulb Replacement

The light bulbs need to be replaced when you notice a dark section of the flame. There are

two bulbs under the log set which generate the flames and embers.

Warning

Disconnect the power before attempting any maintenance or cleaning to reduce the risk of

fire, electric shock or damage to persons.

Warning

Ensure the power cord is not installed so that it is pinched or against a sharp edge and

ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the

risk of fire, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of fire, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

Cleaning Glass

The glass is cleaned in the factory during the assembly operation. During shipment,

installation, handling, etc., the glass surface may collect dust particles, these can be

removed by buffing lightly with a clean dry cloth.

To remove fingerprints or other marks, the glass can be cleaned with a damp cloth using a

good quality household glass cleaner. The glass should be completely dried with a lint free

cloth or paper towel. Do not use abrasive cleaners on glass surface or spray liquids

directly onto any surface.

Surface

Use warm water only to clean painted surfaces. Do not use abrasive cleaners on glass

surface or spray liquids directly onto any surface.

Unit storage

Store the unit when not in use in a dry, dust free location with the power cord properly

secured.

Warning:

Allow at least 10 minutes for the light bulbs and heater to cool before attempting any

maintenance or cleaning.

Bulb Requirements

Quantity 2 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 watt

rating. Example: GE 60BC or Philips 60CTC

www.sylvane.com 1-800-934-9194

Other manuals for DIMPLEX ELECTRIC FIREPLACE

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex IN-STUD V1525BT User manual

Dimplex

Dimplex Revillusion 20" User manual

Dimplex

Dimplex VERDI VER20 User manual

Dimplex

Dimplex Evolve 50 User manual

Dimplex

Dimplex 6911540100 User manual

Dimplex

Dimplex TOLUCA TLC20 Instruction Manual

Dimplex

Dimplex CDFI1000P User manual

Dimplex

Dimplex Montclair User manual

Dimplex

Dimplex Dakota DKT20 User manual

Dimplex

Dimplex DF2608-EU User manual

Dimplex

Dimplex 34" Prism User manual

Dimplex

Dimplex DF3003 User manual

Dimplex

Dimplex Juneau JUN User manual

Dimplex

Dimplex CDFI500P User manual

Dimplex

Dimplex BINGHAM BHM 10 User manual

Dimplex

Dimplex Revillusion RBF30-FG User manual

Dimplex

Dimplex CDFI500-PRO User manual

Dimplex

Dimplex EWMC-CC-SS User manual

Dimplex

Dimplex Winchester WIN28E User manual

Dimplex

Dimplex BF5000NT Quick start guide

Dimplex

Dimplex DF3003 User manual

Dimplex

Dimplex BF45DXP User manual

Dimplex

Dimplex PF2325 User manual

Dimplex

Dimplex BFSL33 User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual