Dimplex 30" FIREPLACE User manual

PRACTICAL USER’S GUIDE

FOR THE ELECTRIC FIREPLACE

MODEL NUMBER:

30” FIREPLACE

Valued Customer,

We are pleased that you have chosen

to purchase an electric fireplace

manufactured by Dimplex North America

Ltd.

Over the years, valuable memories

will occur around the warmth and

comfort of your hearth. Thank you for

Quality checked by:

allowing our product to be the

backdrop for those special moments.

CONTENTS

PAGE 1 Important Instructions

PAGE 2 Model and Serial Number

Information

PAGE 3 Site selection and preparation

PAGE 4 Fireplace installation

PAGE 5 Operation

PAGE 8 Maintenance

PAGE 11 Warranty

7205450200REV05

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC

FIREPLACE

1. Prior to the first use of the fireplace verify the following:

• Are the circuit breakers for the unit on?

• Are the light bulbs in your fireplace loose? (to check, follow the

instructions for replacing the light bulbs under the maintenance

section of this manual)

2. The heater on your fireplace may emit a slight, harmless odor when

first used. This odor is a normal condition caused by the initial

heating of internal heater parts and will not occur again.

3. The information regarding the model of your fireplace can be found

on the rating plate located on the top of the unit.

4. If you have any technical questions or concerns regarding the

operation of your fireplace, or require service contact Dimplex North

America customer service at 1-888-DIMPLEX (1-888-346-7539) before

returning the product to the point of purchase.

IMPORTANT INSTRUCTIONS

SAVE THESE INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using the electric fireplace.

2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. The trim around the heater outlet becomes hot during heater operation. Keep

combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains

at least 3 feet (0.9m) from the front of the unit.

3. Extreme caution is necessary when any heater is used by or near children or invalids

and whenever the unit is left operating and unattended.

4. Always unplug the electric fireplace when not in use.

5. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned,

or if the electric fireplace has been dropped or damaged in any manner. Return heater

to authorized service facility for examination, electrical or mechanical adjustment, or

repair.

6. Do not use outdoors.

7. The electric fireplace is not intended for use in bathrooms, laundry areas and similar

indoor locations. Never locate heater where it may fall into a bathtub or other water

container.

8. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the

like. Arrange cord away from traffic area and where it will not be tripped over.

9. To disconnect the unit, turn the controls off, then remove the plug from the outlet.

10.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this

may cause an electric shock or fire, or damage to the heater.

11.To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use

on soft surfaces, like a bed, where openings may become blocked.

12.All electrical heaters have hot and arching or sparking parts inside. Do not use in areas

where gasoline, paint, or flammable liquids are used or stored or where the unit will be

exposed to flammable vapors.

13.Do not modify the electric fireplace. Use it only as described in this manual. Any other

use not recommended by the manufacturer may cause fire, electric shock or injury to

persons.

14.Avoid the use of an extension cord. Extension cords may overheat and cause a risk of

fire. If you must use an extension cord, the cord must be No. 16 AWG minimum size

and rated no less than 1875 watts.

15.Do not burn wood or other materials in the electric fireplace.

16.Do not strike the fireplace glass.

17.Always use a certified electrician should new circuits or outlets be required.

18.Always use properly grounded, fused and polarized outlets.

19.Disconnect all power supply before performing any cleaning, maintenance or relocation

of the unit.

20. When transporting or storing the unit and cord, keep in a dry place, free from excessive

vibration and store so as to avoid damage.

NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to

the equipment.

WARNING: Procedures and techniques which, if not carefully followed, will expose the user to

the risk of fire, serious injury, illness or death. 1

Model Number

Serial Number

IMPORTANT INSTRUCTIONS

If you have any questions about our products please have the product model and serial

numbers available upon calling Dimplex customer service. To locate the model and serial

number labels see below.

Firebox Carton

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all

cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse

blows on a regular basis when the heater is operating. Additional appliances on the same

circuit may exceed the current rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure

that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire,

electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of fire, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

SITE SELECTION AND PREPARATION

This section provides easy step by step instructions for selecting a location and preparing the

site to install the fireplace into:

• Existing Fireplace

• New wall construction

• Dimplex mantel surround kit or custom made mantel surround

NOTE

The fireplace insert comes completely assembled and wired. Some tools may be required to

prepare the site and assembly/install the trim.

The dimensions of the fireplace insert are 30” wide X 25 ¼” high X 11 ¼” deep. (FIGURE 1)

You should allow ¼” around the fireplace insert for ease of installation.

This fireplace does not require any venting.

CAUTION

Clearance for air circulation beneath the fireplace insert is provided by three rubber feet (FIGURE 1).

DO NOT INSTALL THE FIREPLACE INSERT DIRECTLY ON CARPET OR SIMILAR

SURFACES WHICH MAY RESTRICT AIR CIRCULATION. If installing the fireplace in a

carpeted area, place a one-piece, solid, flat surface under the fireplace insert. Ensure that all

three of the insert’s feet rest securely on this surface.

EXISTING FIREPLACE INSTALLATION

1. Seal all drafts and vents with non-fibrous insulation materials to prevent chimney debris

from falling into the fireplace insert. Do not install into an existing fireplace that is prone

to leaks or dampness.

2. Cap the top of the chimney flue to prevent rain from entering.

3. Plan your electrical power supply: (refer to NOTE 1)

4. The power cord can run along the front of the hearth to an outlet near the fireplace

(FIGURE 2).

NOTE 1

A 15 AMP, 120 VOLT circuit is required. A dedicated circuit is preferred but not essential in

all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or

fuse blows on a regular basis when the heater is operating. Additional appliances on the

same circuit may exceed the current rating of the circuit breaker.

WARNING

To prevent personal injury you should hire a professional to cap the chimney flue or cut a

hole in the existing fireplace for wiring.

If you return your existing fireplace to its original use (Example wood burning), it should be

inspected by the local building department prior to use to reduce the risk of fire and

personal injury.

NEW WALL CONSTRUCTION

1. Select a suitable location that is not susceptible to moisture and is away from drapes,

furniture and high traffic.

2. Place the fireplace in the desired location to see how it will look in the room.

3. Mark the desired location on the floor and store the fireplace in a safe, dry and dust free

location.

4. Use studs to frame an opening of 30 ½” wide X 25 ¾” high X 11 ¾” deep.

5. Plan your electrical power supply (refer to NOTE 1)

Option #1-The power cord can be lead from behind the trim and along the wall to an outlet

near the fireplace.

Option #2-A new outlet can be installed inside the new frame construction.

DIMPLEX MANTEL SURROUND KIT OR CUSTOM MADE MANTEL SURROUND

1. Select a suitable location that is not susceptible to moisture and is away from drapes,

furniture and high traffic.

2. Place the fireplace in the desired location to see how it will look in the room.

3. For ease of electrical hook up you may wish to locate the fireplace near an existing

outlet. (refer to NOTE 1)

4. Store the fireplace in a safe dry and dust free location.

5. Assemble the mantel surround kit (refer to the mantel assembly instructions) or

construct the custom surround with an opening of 30 ½” X 11 ¾ ” X 25 ¾”

WARNING

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric

shock or injury to persons, always use a licensed electrician.

FIREPLACE INSERT INSTALLATION

1. Make sure the units MAIN ON/OFF switch is switched OFF (refer to operating

instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you may use an

extension cord rated for a minimum of 1875 watts.

3. Push the fireplace into the opening being careful not to damage the base of the mantel

or cabinet so that the fireplace is flush with the mantel or cabinet.

4. Level the unit with shims if necessary (not provided).

5. Install the trim onto the fireplace (refer to trim installation instructions).

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and

ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the

risk of fire, electric shock or injury to persons.

OPERATION

Initializing The Remote Control

1. Turn on the electrical power at the circuit breaker.

2. Slide open the battery cover on the back of the remote transmitter.

3. Install three AAA batteries into the remote control. Replace the battery cover.

Note:

The LCD display will flash when new batteries are inserted.

4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press

any button on the remote control. The remote is transferring the code to the receiver

built into the fireplace.

5. Set the clock by depressing the button marked clock on the transmitter for five seconds.

The hour display will flash.

6. Use the up and down buttons to set the hour.

7. Press the clock button again and the minute display will flash.

8. Use the up and down buttons to set the minute.

9. Press the clock button again and the

F or

C display will flash.

10.Use the up and down buttons to select the remote to display temperature in

F or

11.Press the clock button again. The remote control is now ready for operation.

OPERATION

Remote Control Operation

Warning:

It takes some time for the receiver to respond to the transmitter. Do not press the buttons

more than once within two seconds for correct operation.

Note:

The fireplace has an automatic timer function that will shut your fireplace off if the remote

control has not been operated within a six-hour period.

Auto Mode

Note:

When auto mode is activated the flame and heat will turn on. The heater will turn on and

off to keep the room temperature the same as the remote controls set temperature.

1. Press POWER button to turn unit on. (There may be a slight delay)

2. Press the UP or DOWN buttons to change the set temperature, if desired.

3. In auto mode the remote transmitter will automatically turn on the flame and heater

when the room temperature is below the target temperature and turn off the heater

ONLY when the room temperature is above the target temperature.

4. Press POWER button once to turn unit off.

Timer Mode

1. You can set the timer to the length of time you want the unit to operate

2. (1 to 120 minutes).

3. Press the TIMER button once. The timer display will blink ---

4. Press the UP and DOWN buttons to adjust the timer display in minutes.

5. Press the TIMER button once to set the timer.

6. The timer setting can be reset by pressing the TIMER button and using the DOWN

button until the timer display reads ----, press the TIMER button once to set the timer.

7. Press the POWER button to turn the unit on.

8. The fireplace will automatically shut off when the timer reaches 0 minutes.

Child Proof Function

1. Remove the battery cover on the back of the remote control.

2. Slide the small blue switch down to activate the child proof function.

3. Child Proof will appear on the display screen and all function on the remote will be

locked.

4. To enable normal remote control operation when the child proof function is activated,

press the up and down buttons in the following sequence,

UP-DOWN-DOWN-UP-DOWN the remote functions will now operate normally. The

remote will return to the child proof function if buttons are not pressed after two minutes.

5. To disable the child proof function remove the battery cover on the back of the remote

and slide the small blue switch up.

Batteries

1. The remote control uses 3 AAA size batteries (included). Replace these batteries at

least every 6 months or when the low battery appears on the remote display screen.

2. When batteries are removed wait at least 1 minute before replacing with new batteries.

Code selection

If the current remote control is interfering with the operation of other remote control devices

(TV, VCR, garage doors etc.) The code can be changed on the remote.

To change code:

1. Remove the battery cover on the back of the remote control.

2. Slide the four small switches to any configuration other than the factory set code.

3. Remove the batteries, wait for one minute.

4. Install the batteries.

5. Install the battery cover onto the remote.

6. Reinitialize the remote.

Other manuals for 30" FIREPLACE

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex MULTI-FIRE SL PLF3614-XS User manual

Dimplex

Dimplex DF2624L-INT User manual

Dimplex

Dimplex DF1870L User manual

Dimplex

Dimplex BLF74 Building instructions

Dimplex

Dimplex COVELO User manual

Dimplex

Dimplex EF2870L User manual

Dimplex

Dimplex DF2305 User manual

Dimplex

Dimplex WBK20 User manual

Dimplex

Dimplex LKD20-AU User manual

Dimplex

Dimplex DF3033ST User manual

Dimplex

Dimplex 3-STEP Optimyst Instruction Manual

Dimplex

Dimplex CFP49449BW User manual

Dimplex

Dimplex 6908760100 User manual

Dimplex

Dimplex Opti-Myst Cassette 500 User manual

Dimplex

Dimplex DWF36-PG User manual

Dimplex

Dimplex DF2608-EU User manual

Dimplex

Dimplex CDS6599 - Celeste User manual

Dimplex

Dimplex SAHARA SHR12 User manual

Dimplex

Dimplex BLF5051-AU/PRISM 50" User manual

Dimplex

Dimplex SPF1808L-IR User manual

Dimplex

Dimplex CHERITON LED CHT20 User manual

Dimplex

Dimplex OPTIMYST CAS400L User manual

Dimplex

Dimplex MILANOef EDS7001F Quick start guide

Dimplex

Dimplex DWF1146GP User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual