Dimplex Somerley SOM20 User manual

01/02 SHAFTSBURY SHA20 PAGE 1

Shaftsbury SHA20

01/02 SHAFTSBURY SHA20 PAGE 2

Dimplex – SHAFTSBURY

Shaftsbury SHA20

14 15

01/02 SHAFTSBURY SHA20 PAGE 3

TECHNICAL DATA

Model SHA20

Colour Black & Brass

Country of Origin Irish Republic

Fuel Effect Optiflame Elite (log)

Heat Source Fan Heater

Thermostat Bi-metal leaf

Electrical Supply 230- 240 Volts 50 Hz AC

Total Loading: 1956-2136 Watts

Elements: 1820-2000 Watts

Lamps: 2 x 60 Watts BC Lamps

Motors: 2 x 6.5 Watts, 1 x 2.5 Watts

SERVICING AND DISMANTLING INSTRUCTIONS

ENSURE APPLIANCE IS DISCONNECTED FROM THE ELECTRICITY SUPPLY BEFORE DISMANTLING.

NOTE ALL CONNECTION DETAILS AND ROUTING OF LEADS BEFORE DISMANTLING.

ALWAYS REPLACE CABLE TIES ON RE-ASSEMBLY.

Numbers appearing in the text refer to illustrations and parts list numbers.

LAMP REPLACEMENT

1.1 Grasp the grate 17 and lift it upward and away from the fire. Grasp the fuel effect and ease it out past

grate retaining screws at position "A", then lift it away.

1.2 Grip the defective lamp near its centre and rotate the lamp anti-clockwise until it comes out of its

holder. Replace the defective lamp with a 240V, 60W BC Fireglow lamp.

1.3 Reassemble, ensuring that the fuel effect sits correctly behind the grate retaining screws at position

"A", then refit the grate, engaging the hooked brackets over the two retaining screws.

MAINS CABLE

2.1 Remove the grate and fuel effect as detailed in 1.1 above, and lay the fire on its back on a soft surface.

2.2 Release the two screws securing terminal cover box "B", from underneath the chassis, and lift the box

away with light baffle "C" attached.

2.3 Disconnect the live and neutral leads from terminal block 22 and the earth screw assembly. Release

cable clamp arm 11 by squeezing the barbs from inside the chassis. Use a pair of long-nosed pliers to

squeeze the cable clamp locking tab and withdraw the clamp 11 and cable 12.

2.4 Reassemble, ensuring that wires are not trapped by the terminal cover box.

LOG FLAME EFFECT

3.1 Remove the grate and fuel effect and terminal cover box "B" as detailed in 2.1 and 2.2 above.

3.2 Detach the leads from rotisserie motor 12 to the terminal block 1. Cut cable ties where necessary to

thread the motor leads through the heat sleeving.

3.3 Release the two screws holding motor bracket "E", grasp motor coupling 13 and withdraw motor 12.

Flames rotisserie 14 is also a push fit on coupling 13 and the other end sits loosely in grommet bush

15.

3.4 To detach the motor, release the two bright screws attaching it to the motor bracket.

3.5 Reassemble in reverse order, ensuring that cable ties are replaced where necessary and that no wires

are trapped by the terminal cover box. Check that the rotisserie rotates without obstruction before

refitting the fuel effect.

01/02 SHAFTSBURY SHA20 PAGE 4

60W

LAMP

60W

LAMP

ROTALINK

10 RPM

CUT-OUT

III

123

HEAT

FAN1KW

III

1KW

EFFECT

FAN

REAR FLAME EFFECT

4.1 Remove the grate and fuel effect and terminal cover box "B" as detailed in 2.1 and 2.2 above.

4.2 Remove glass retaining panels "F", each secured by two screws inside and one outside the chassis, and

lift mirrored glass 19 clear.

4.3 Remove motor guard "G", secured by one screw from the rear and one from undermeath the chassis.

4.4 Blower unit 8 is secured by four screws, from the underside of the chassis.

4.5 Connections are by push-on terminals. Note positions before disassembling.

4.6 Cloth flags hook onto supports at top and bottom. Ensure all flags hang freely.

4.7 Reassemble in reverse order, ensuring that cable ties are replaced where necessary and that no wires

are trapped by the terminal cover box.

FAN HEATER AND CONTROLS

5.1 Remove the log effect, and lay the fire on its back on a soft surface.

5.2 Remove the mirrored glass, as detailed in 4.2 above.

5.3 Stand the fire back up and remove the four screws at position "X", securing the surround to the chassis

and lift the surround away.

5.4 Remove the two screws near the top of the rear panel and, whilst supporting the fan heater assembly,

the two screws at position "Y" in the top of the chassis securing the fan heater assembly. The heater

assembly can now be positioined in front of the chassis to the extent of the connecting leads.

5.5 Canopy hood 21 is secured by pop rivets. Drill out the rivets, and on reassembly replace with rivets size

M3.2 - 6.5mm.

5.6 Heat blower unit 3 is secured to the control panel by four screws. Element 4 is secured to the blower unit

by four screws and cut-out 5 is secured to the element by a single screw.

5.7 The switches are a push fit; compress the clips on the switch body and ease the switch 1 forward and

out. Note connections before disconnecting push-on terminals.

5.8 Thermostat 6 is secured by two screws through the control panel; pull off control knob 2 to access the

screws.

AFTER SERVICING, IT IS RECOMMENDED THAT THE PRODUCT IS TESTED FOR INSULATION AND

EARTH CONTINUITY, IN ACCORDANCE WITH RELEVANT LOCAL SAFETY REGULATIONS.

THEORETICAL WIRING DIAGRAM – SHA20

PARTS LIST SHAFTESBURY SHA20 LOG

ITEM CAT NO WATTS VOLTS DESCRIPTION COLOUR MODEL

1 BF7211 SWITCH

2 FP00012 CONTROL KNOB

3 FP9557 BLOWER UNIT HEAT SER A

FP01072 BLOWER UNIT HEAT SER B - D

FP03029 BLOWER UNIT HEAT SER E

4 FP9410 2000 230/240 ELEMENT ASSY SER A

FP01073 2000 230/240 ELEMENT ASSY C/W CUT OUT SER B - D

FP03030 2000 230/240 ELEMENT ASSY C/W CUT OUT SER E

5 FB9402 CUT OUT SER A

6 BF9433 THERMOSTAT

7 FP01003 CLOTH FLAGS x 10

8 FP00003 BLOWER UNIT

9 BF7223 60 LAMPS RED

10 BF7226 LAMPHOLDER

11 FP9005 CABLE CLAMP

12 FP9929 GEARED MOTOR 10RPM

13 FP20007 MOTOR COUPLING

14 FP20005 ROTISSERIE FLAMES

15 FP9554 RUBBER GROMMET

16 FP01094 SURROUND ASSY

17 FP01096 GRATE ASSY

18 FP01095 LOG EFFECT

19 FP01084 MIRRORED GLASS

20 FP9605 GLASS RUBBER BUFFERS

21 FP01058 CANOPY HOOD

22 BU9502 TERMINAL BLOCK

03/04 SHAFTESBURY SHA20 LOG PAGE 198

01/02 SOMERLEY SOM20

Somerley SOM20

01/02 SOMERLEY SOM20

Dimplex – SOMERLEY

Somerley SOM20

01/02 SOMERLEY SOM20

TECHNICAL DATA

Model SOM20

Colour Black & Brass

Country of Origin Irish Republic

Fuel Effect Optiflame Plus (Real Coal)

Heat Source Fan Heater

Thermostat Bi-metal leaf

Electrical Supply 230- 240 Volts 50 Hz AC

Total Loading: 1956-2136 Watts

Elements: 1820-2000 Watts

Lamps: 2 x 60 Watts BC Lamps

Motors: 2 x 6.5 Watts, 1 x 2.5 Watts

SERVICING AND DISMANTLING INSTRUCTIONS

ENSURE APPLIANCE IS DISCONNECTED FROM THE ELECTRICITY SUPPLY BEFORE DISMANTLING.

NOTE ALL CONNECTION DETAILS AND ROUTING OF LEADS BEFORE DISMANTLING.

ALWAYS REPLACE CABLE TIES ON RE-ASSEMBLY.

Numbers appearing in the text refer to illustrations and parts list numbers.

LAMP REPLACEMENT

1.1 Remove coal as necessary, then grasp the grate/fuel effect assembly 15, 16 and lift it upward and

away from the fire.

1.2 Grip the defective lamp, push in and twist it anti-clockwise to release it from its holder. Replace the

defective lamp with a 240V, 60W BC Fireglow lamp.

1.3 Reassemble, ensuring that the grate/fuel effect assembly engages the hooked brackets over the two

retaining screws at position “A”.

MAINS CABLE

2.1 Remove the grate/fuel effect assembly as detailed in 1.1 above, and lay the fire on its back on a soft

surface.

2.2 Release the two screws securing terminal cover box "B", from underneath the chassis, and lift the box

away with light baffle "C" attached.

2.3 Disconnect the live and neutral leads from terminal block 20 and the earth screw assembly. Release

cable clamp arm 11 by squeezing the barbs from inside the chassis. Use a pair of long-nosed pliers to

squeeze the cable clamp locking tab and withdraw the clamp 11 and cable 12.

2.4 Reassemble, ensuring that wires are not trapped by the terminal cover box.

FLAME EFFECT

4.1 Remove the grate/fuel effect assembly and terminal cover box "B" as detailed in 2.1 and 2.2 above.

4.2 Remove glass retaining panels "E", each secured by two screws inside and one outside the chassis,

and lift mirrored glass 17 clear.

4.3 Remove motor guard "F", secured by one screw from the rear and one from undermeath the chassis.

4.4 Blower unit 8 is secured by four screws, from the underside of the chassis.

4.5 Connections are by push-on terminals. Note positions before disassembling.

4.6 Cloth flags 7 hook onto supports at top and bottom. Ensure all flags hang freely.

4.7 Reassemble in reverse order, ensuring that cable ties are replaced where necessary and that no wires

are trapped by the terminal cover box.

01/02 SOMERLEY SOM20

60W

LAMP

60W

LAMP

CUT-OUT

III

123

HEAT

FAN1KW

III

1KW

EFFECT

FAN

FAN HEATER AND CONTROLS

5.1 Remove the grate/fuel effect assembly, as detailed in 1.1 above, and lay the fire on its back on a soft

surface.

5.2 Remove the mirrored glass 17, as detailed in 4.2 above.

5.3 Stand the fire back up and remove the four screws at position "X", securing the surround to the chassis

and lift the surround away.

5.4 Remove the two screws near the top of the rear panel and, whilst supporting the fan heater assembly,

the two screws at position "Y" in the top of the chassis securing the fan heater assembly. The heater

assembly can now be positioined in front of the chassis to the extent of the connecting leads.

5.5 Canopy hood 21 is secured by pop rivets. Drill out the rivets, and on reassembly replace with rivets size

M3.2 - 6.5mm.

5.6 Heat blower unit 3 is secured to the control panel by four screws. Element 4 is secured to the blower unit

by four screws and cut-out 5 is secured to the element by a single screw.

5.7 Switches 1 are a push fit; compress the clips on the switch body and ease the switch forward and out.

Note connections before disconnecting push-on terminals.

5.8 Thermostat 6 is secured by two screws through the control panel; pull off control knob 2 to access the

screws.

AFTER SERVICING, IT IS RECOMMENDED THAT THE PRODUCT IS TESTED FOR INSULATION AND

EARTH CONTINUITY, IN ACCORDANCE WITH RELEVANT LOCAL SAFETY REGULATIONS.

THEORETICAL WIRING DIAGRAM – SOM20

PARTS LIST SOMERLEY SOM20

ITEM CAT NO

ATT

VOLTS DESCRIPTION COLOUR MODEL

1 BF7211 S/P SWITCH

2 FP00012 CONTROL KNOB PRINTED GOLD

3 FP9557 HEAT BLOWER UNIT SER A

FP01072 HEAT BLOWER UNIT SER B - C

FP03029 HEAT BLOWER UNIT SER D

4 FP9410 2000 230/240 ELEMENT SER A

FP01073 2000 230/240 ELEMENT C/ CUT OUT SER B - C

FP03030 2000 230/240 ELEMENT C/ CUT OUT SER D

5 FB9402 CUT OUT (OTTER V-10) SER A

6 BF9433 THERMOSTAT

7 FP01003 CLOTH FLAGS

8 FP00003 EFFECT BLOWER UNIT

9 BF7223 60 LAMPS FIREGLOW RED

10 BF7226 LAMPHOLDER

11 FP9005 CABLE CLAMP

12 FP20020 PLUG & LEAD ASSY

13 FP01057 SURROUND ASSY

14 FP01034 COAL PACK

15 FP00056 GRATE ASSY

16 FP00055 FUEL EFFECT

17 FP01084 REAR GLASS

18 FP9605 RUBBER GLASS BUFFERS

19 FP01058 CANOPY HOOD

20 BU9502 2 WAY TERMINAL BLOCK 16AMP

02/04 SOMERLEY SOM20 PAGE 203

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex TIMRA TMR15 Installation guide

Dimplex

Dimplex Prism BLF5051 User manual

Dimplex

Dimplex SP420 User manual

Dimplex

Dimplex LIBERTY SUITE LBY15-AU User manual

Dimplex

Dimplex DF2024 User manual

Dimplex

Dimplex Devon User manual

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Operating instructions

Dimplex

Dimplex DF2426GB User manual

Dimplex

Dimplex DF2550-EU User manual

Dimplex

Dimplex DLW1500B12 User manual

Dimplex

Dimplex Figaro FGA15 User manual

Dimplex

Dimplex Dakota User manual

Dimplex

Dimplex COMPACT FIREPLACE User manual

Dimplex

Dimplex SP320 User manual

Dimplex

Dimplex EXBURY EBY15 User manual

Dimplex

Dimplex MULTIFIRE DF3215 Quick start guide

Dimplex

Dimplex BF33STP/DXP User manual

Dimplex

Dimplex ELBA User manual

Dimplex

Dimplex CASTILLO CS3540 User manual

Dimplex

Dimplex Pro Engine series Instruction Manual

Dimplex

Dimplex BF8000ST User manual

Dimplex

Dimplex CAS500R User manual

Dimplex

Dimplex Revillusion RLG20 EU User manual

Dimplex

Dimplex TOLUCA TLC20 User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual