Dimplex Revillusion RBF24DLX User manual

Service Manual

Model

RBF24DLX

RBF30

RBF36

RBF36P

RBF42

Part Number

6909990100

6909780100

6909790100

6909790200

6909800100

7400970000R02

IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to service this rebox.

For your safety, always comply with all warnings and safety instructions contained in this manual to prevent

personal injury or property damage.

2 www.dimplex.com

Always use a qualied technician or service agency to repair this rebox.

!NOTE: Procedures and techniques that are considered important enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.

WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of re, serious

injury, or death.

Operation - RBF30, RBF36, RBF36P, RBF42....................................3

Operation - RBF24DLX .....................................................5

Maintenance..............................................................7

Exploded Parts Diagram - RBF30, RBF36, RBF36P, RBF42 .......................8

Replacement Parts List ...............................................8

Exploded Parts Diagram - RBF24DLX .........................................9

Replacement Parts List ...............................................9

Wiring Diagram - RBF30, RBF36, RBF36P, RBF42 .............................. 10

Wiring Diagram - RBF24DLX ...............................................10

Preparing for Service ..................................................... 11

Ember LED Light Replacement .............................................12

Flame Base LED Replacement..............................................12

Flame LED Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Flicker Motor Replacement (RBF30, RBF36, RBF36P, RBF42) ....................12

Flicker Motor Replacement (RBF24DLX)......................................12

Main Control Board Replacement ...........................................13

Power Supply Replacement ................................................13

Blower Assembly Replacement (RBF30, RBF36, RBF36P, RBF42) .................14

Element Replacement (RBF30, RBF36, RBF36P, RBF42) .........................14

Cutout Replacement (RBF30, RBF36, RBF36P, RBF42) ..........................15

Heater Assembly Replacement (RBF24DLX) ..................................15

Touch Pad Replacement ...................................................16

Thermistor Replacement (RBF24DLX)........................................16

Thermistor Replacement (RBF30, RBF36, RBF36P, RBF42) ......................17

Top Front Lights Replacement..............................................17

Rear Top Lights Replacement ..............................................17

Troubleshooting Guide ....................................................18

TABLE OF CONTENTS

Operation - RBF30, RBF36, RBF36P, RBF42

Touch Panel and Remote Controls

WARNING: The RevillusionTM Built-in Electric Firebox must be installed properly before it is used.

CAUTION: Except for installation and cleaning described in this manual, an authorized service representative should

perform any other servicing.

The manual controls for the RevillusionTM Built-in Electric Firebox are located on the front panel. Touch an icon to activate.

The selected setting displays on the left side of the panel.

A multi-function remote control also is provided. The remote control has a range of approximately 30’ (9 m). To operate

correctly, the remote control must be pointed toward the front of the built-in electric rebox.

Icon Function Description

APower/

Standby

Press to activate the current standby state (On/O󰀨).

• Standby State On

Press to turn everything O󰀨. Press again to activate the previous state.

• Standby State O󰀨

Press to activate the previous state.

- If the ame e󰀨ect was On, the previous heat setting will be activated (On or O󰀨).

- If the ame e󰀨ect was O󰀨, the previous heat setting will be activated (High or Low).

Press again to turn everything O󰀨.

BHeat

• Heat On

Press to turn heat On (indicated by 1 short beep and the icon appearing on the display).

Displays current heater temperature setting. Use the Temp Up/Down icon to change the

heater temperature setting.

• Heat O󰀨

Press to turn heat O󰀨 (indicated by 1 short beep).

!NOTE: After the heater is switched o󰀨, the fan will continue on for 60 seconds before

turning o󰀨.

Figure 1

Figure 2

4 www.dimplex.com

Icon Function Description

CTemp Down

Press multiple times to lower the heater temperature in 10 F (10 C) increments. Displays

current temperature; lowest temperature is 410 F (50 C). This feature is active whenever

the heat is enabled.

DTemp Up

Press multiple time to raise the heater temperature in 10 F (10 C) increments. Displays

current temperature; highest temperature is 990 F (370 C). This feature is active whenever

the heat is enabled.

Change Fahrenheit (0 F) to

Celsius (0 C) Press both Temp+ ( ) and Temp– ( ) on the unit.

Heat Enable

Heat Disable

Hold both Heat ( ) and Temp– ( ), on the unit, for 2 seconds. Temperature displays

on the screen.

Hold both Heat ( ) and Temp– ( ), on the unit, for 2 seconds, when temperature is

adjusted "---" displays on the screen.

EColor

Themes

Press multiple times to change the ame base colors from Red to Blue to O󰀨. (The rst

segment on the display will change from "r" to "b" to blank) This feature is active only

when the ame e󰀨ect is On.

F360oLight

Press multiple times to change the LEDs on the sides and back of the unit from Midnight

mode to white to yellow to red. (The middle segment on the display will change through

0 - 3 respectively. This feature is active only when the Flame is ON.)

GBrightness

Press to change the LED lights from High to Low. (The last segment on the display will

change from "H" to "L") The RealogTM LEDs remain On when the heater is ON and the

ame e󰀨ect is O󰀨.

!NOTE: When the Light Sensor is activated, High and Low ickering brightness

settings are also available (Flashing "H" and "L").

HFlame Press to light the log set and start the ame e󰀨ect. Press again to turn feature O󰀨.

ILight

Sensor

Press to activate the ambient light sensor (ALS ON). Press again to turn the sensor o󰀨

(ALS OFF).

!NOTE: The light sensor will adjust the brightness of the replace based on the

ambient light in the room.

JTimer

Press multiple times to change the sleeper timer in 0.5 hr increments from 0.5 hr to 8.0 hr

before turning o󰀨. The remaining time on the sleep timer displays.

Control Lock

Control Unlock

Hold both Temp– ( ) and Brightness ( ), on the unit, for 2 seconds to disable the

manual controls.

Hold both Temp– ( ) and Brightness ( ), on the unit, for 2 seconds to enable the

manual controls.

Resetting the Temperature Cuto󰀨 Switch

Should the heater overheat, an automatic cut out will turn the heater o󰀨 and it will not come back on without being reset. It

can be reset by disconnecting power at the main electrical panel and waiting 5 minutes before plugging the unit back in.

CAUTION: If you need to con tinuously reset the heater, unplug the unit and call technical support at 1-888-346-7539.

Operation - RBF24DLX

Icon Function Description

APower/Standby

Press to activate the current standby state (On/O󰀨).

• Standby State On

Press to turn everything O󰀨. Press again to activate the

previous state.

• Standby State O󰀨

Press to activate the previous state.

- If the ame e󰀨ect was On, the previous heat setting will be activated (On

or O󰀨).

- If the ame e󰀨ect was O󰀨, the previous heat setting will be activated (High

or Low).

Press again to turn everything O󰀨.

BFlame

Press to light the log set and start the ame e󰀨ect. Press again to turn feature

O󰀨.

CTemp Down

Press multiple times to lower the heater temperature in 1 °F (1 °C) increments.

Displays current temperature; lowest temperature is 41 °F (5 °C). This feature is

active whenever the heat is enabled.

Icon Function Description

DFlame Speed

Press multiple times to toggle through the ame speeds (minimum, medium,

maximum). The display will show the current speed number, F1, F2 or F3.

EColor

Themes

Press multiple times to change the ame base colors from Red to Blue to O󰀨.

(The rst segment on the display will change from "r" to "b" to blank) This feature

is active only when the ame e󰀨ect is On.

E I

6 www.dimplex.com

Icon Function Description

F360oLight

Press multiple times to change the LEDs on the sides and back of the unit from

Midnight mode to white to yellow to red. (The middle segment on the display will

change through 0 - 3 respectively. This feature is active only when the Flame is

ON.)

GTimer Press multiple times to change the sleeper timer in 0.5 hr increments from 0.5 hr

to 8.0 hr before turning o󰀨. The remaining time on the sleep timer displays.

HLight

Sensor

Press to activate the ambient light sensor (ALS ON). Press again to turn the

sensor o󰀨 (ALS OFF).

!NOTE: The light sensor will adjust the brightness of the replace based on

the ambient light in the room.

IBrightness

Press to change the LED lights from High to Low. (The last segment on the

display will change from "H" to "L") The RealogTM LEDs remain On when the

heater is ON and the ame e󰀨ect is O󰀨.

!NOTE: When the Light Sensor is activated, High and Low ickering

brightness settings are also available (Flashing "H" and "L").

JHeat Mode

Press the multiple time to toggle through the heat modes (Normal, Eco and

Boost). Normal is indicated with a Nor on the display, ECO is indicate by an Eco

on the display and Boost is indicate by a b20 on the display. In boost mode, a

time is set initial for 20 minutes and the display will indicate b19, b18, etc., as the

time counts down. This is shown by pressing the heat mode button.

KTemp Up

Press multiple time to raise the heater temperature in 1 °F (1 °C) increments.

Displays current temperature; highest temperature is 99 °F (37 °C). This feature is

active whenever the heat is enabled.

Change Fahrenheit (°F)

to Celsius (°C) Press both Temp+ ( ) and Temp– ( ) on the unit.

Heat Enable

Heat Disable

Hold both Heat ( ) and Temp– ( ), on the unit, for 2 seconds. Temperature

displays on the screen.

Hold both Heat ( ) and Temp– ( ), on the unit, for 2 seconds, when

temperature is adjusted "---" displays on the screen.

LHeat

• Heat On

Press to turn heat On (indicated by 1 short beep and the icon appearing on the

display). Displays current heater temperature setting. Use the Temp Up/Down

icon to change the heater temperature setting.

• Heat O󰀨

Press to turn heat O󰀨 (indicated by 1 short beep).

!NOTE: After the heater is switched o󰀨, the fan will continue on for 60

seconds before turning o󰀨.

Control Lock

Control Unlock

Hold both Temp– ( ) and Brightness ( ), on the unit, for 2 seconds to

disable the manual controls.

Hold both Temp– ( ) and Brightness ( ), on the unit, for 2 seconds to enable

the manual controls.

Maintenance

General Maintenance

Inspect the built-in electric rebox regularly, depending

upon conditions, and at a minimum yearly intervals.

Remove dust and clean the logs, grate, and base as

required.

WARNING: Disconnect power and allow heater to

cool before attempting any maintenance or cleaning to

reduce the risk of re, electric shock, or injury.

CAUTION: Except for installation and cleaning

described in this manual, an authorized service

representative should perform any other servicing.

Clean Logs and Base

The built-in electric rebox set should not be operated with

an accumulation of dust or dirt on or in the rebox, as this

can cause a build up of heat and eventual damage.

Dust and vacuum the rebox as needed. Use a damp cloth

and a mild detergent to clean painted surfaces of the built-

in electric rebox. Never use abrasive cleaners.

Clean Reector Screen

The reector screen is cleaned in the factory during the

assembly operation. During shipment, installation, handling,

etc., the screen may collect dust particles; these can be

removed by dusting lightly with a clean dry cloth.

To remove ngerprints or other marks, clean the reector

screen damp cloth. Never use abrasive cleaners. Dry the

screen completely with a lint free cloth to prevent water

spots.

Remote Battery Replacement

To replace the battery:

1. Push down on the battery cover located on the back of

the remote control. Slide the battery cover open.

2. Install 3V (CR2032) Lithium battery in the battery

holder. The positive (+) side of the battery faces up.

3. Close the battery cover.

The old battery must be recycled or disposed of properly.

Check with your Local Authority or Retailer for recycling

advice in your area.

CAUTION: When transporting or storing the heater and cord,

keep in a dry place, free from excessive vibration and store

so as to avoid damage.

8 www.dimplex.com

Exploded Parts Diagram - RBF30, RBF36, RBF36P, RBF42

Replacement Parts List

1. Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 2100250100RP

2. Main Control Board ....................3001810101RP

3. Touch Pad ...........................3001830100RP

4. Blower Assembly ......................5300110500RP

5. Heater Elements. . . . . . . . . . . . . . . . . . . . . . . 2200510700RP

6. Cutout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2300201900RP

7. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . . 2000501000RP

8. Remote Control .......................3001710100RP

9. Thermistor ...........................3001560800RP

10. Flame Base (RGB) RBF30. . . . . . . . . . . . . . . 3001790100RP

RBF36, RBF36P, RBF42

3001790200RP

11. Back log LED RBF30 . . . . . . . . . . . . . . . . . . . 3001760200RP

RBF36, RBF36P, RBF42

.....3001760300RP

12. Ember LED RBF30. . . . . . . . . . . . . . . . . . . . . 3001820100RP

RBF36, RBF36P, RBF42

. . . . . . . 3001820200RP

13. Top Back Light (RGB). . . . . . . . . . . . . . . . . . . 3001570100RP

14. Top Front Lights (2 sets) RBF30 ..........3001570600RP

RBF36, RBF36P 3001570500RP

RBF42. . . . . . . . . . . 3001570401RP

15. Flame Screen RBF30. . . . . . . . . . . . . . . . . . . 5903010100RP

RBF36. . . . . . . . . . . . . . . . . . . 5903020100RP

RBF36P .................5903020300RP

RBF42. . . . . . . . . . . . . . . . . . . 5903020200RP

16. Log Set Assembly RBF30 ...............0442100100RP

RBF36, RBF36P, RBF42

0442110100RP

17. Brick Panels RBF30 (LH & RH) ...........5902970001RP

RBF36 (LH) ................5902950001RP

RBF36P. . . . . . . . . . . . . . . . . . . 5903060001RP

RBF42 (LH) ................5902960001RP

18. Accessory Glass Hardware ..............9601750100RP

19. Accessory Door Hardware . . . . . . . . . . . . . . . 9601760100RP

Exploded Parts Diagram - RBF24DLX

16 17

Replacement Parts List

1. Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 2100250600RP

2. Main Control Board ....................3002080101RP

3. Touch pad ............................3001830200RP

4. Heater Assembly ......................2203810100RP

5. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . .3000240200KIT

6. Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . 5903040200RP

7. Remote Control .......................3001970100RP

8. Thermistor ...........................0442570100RP

9. Flame Base (RGB) . . . . . . . . . . . . . . . . . . . . . 3001790100RP

10. Flame/Back Log LED . . . . . . . . . . . . . . . . . . . 3001760200RP

11. Ember LED. . . . . . . . . . . . . . . . . . . . . . . . . . . 3001820100RP

12. Top Back Light (RGB). . . . . . . . . . . . . . . . . . . 3001570100RP

13. Top Front Lights (2 sets). . . . . . . . . . . . . . . . . 3001570600RP

14. Flame Screen . . . . . . . . . . . . . . . . . . . . . . . . . 5903010200RP

15. Log Set Assembly. . . . . . . . . . . . . . . . . . . . . . 0442400100RP

16. Brick Panels (LH & RH) .................5903200001RP

17. Weather Concrete Panels (LH & RH). . . . . . . 5903201001RP

18. Front Glass. . . . . . . . . . . . . . . . . . . . . . . . . . . 6909870500RP

19. Front Glass Hardware ..................9601750100RP

20. Power Cord ..............................RBFPLUG

10 www.dimplex.com

Wiring Diagram - RBF30, RBF36, RBF36P, RBF42

Wiring Diagram - RBF24DLX

PCB P/N:

+12v

+5v

GND

+12v

+5v

+12v

CN13

FAN2

CN14

uart

ACN

CN12

FAN1

L-in

IC6

CN7

CN4 NTC

CN2FLAME

CN6

Control Panel

MOT

CN3FLAME

CN1

+12V

HTR2

RY4

HTR1

CN11

T-BK-RGB

CN10

T-FR-RGB

CN9

FLAME-RGB

PZ2

HT EN

ACN

JP6

R24

R12

R11470

R13

AP2952

C12

103

100K

104 C10104

R27

HTR2

HTR1

FAN1

FAN2

CONTROL PANEL

Other manuals for Revillusion RBF24DLX

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex DFB8842 User manual

Dimplex

Dimplex NARVIK NOVA User manual

Dimplex

Dimplex Montclair User manual

Dimplex

Dimplex Figaro FGA15 User manual

Dimplex

Dimplex DCF7850 User manual

Dimplex

Dimplex EF830 User manual

Dimplex

Dimplex DFI2309 User manual

Dimplex

Dimplex Pro Series Technical manual

Dimplex

Dimplex DF2500L User manual

Dimplex

Dimplex VF5452L User manual

Dimplex

Dimplex Montclair User manual

Dimplex

Dimplex BURNHAM BRN20 User manual

Dimplex

Dimplex Opti-myst RTOPW20 User manual

Dimplex

Dimplex 7206560100R00 Installation guide

Dimplex

Dimplex DF3020-EU User manual

Dimplex

Dimplex HAR20 User manual

Dimplex

Dimplex SP120 User manual

Dimplex

Dimplex SS5800PB User manual

Dimplex

Dimplex CAS500R User manual

Dimplex

Dimplex DF2622 User manual

Dimplex

Dimplex Mozart CFP3811GB User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex ELECTRALOG DF203A User manual

Dimplex

Dimplex DWF1146GP User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual