Delta UNOnext User manual
1
UNOnext Wiring Guide
ver 1.5
2021/6/23
2
As long as UNOcentral is connected to a power supply, the system will begin to operate.
Through the HDMI connection on the back of UNOcentral, UNOcentral's screen can be output
to displays with HDMI interfaces, such as computer monitors and TVs. UNOcentral is managed
through a web GUI. Users can remotely manage UNOcentral through the browsers of other
hosts, or directly output UNOcentral to a display and use a USB keyboard and mouse for man-
agement. To use UNOcentral remote management or other network services, it is recommend-
ed to connect the network cable to the LAN1 port on the back of UNOcentral (The MAC address
of LAN1 is provided on the UNOcentral’s label). As shown in Figure 1
If RS485 communication interface is used between UNOcentral and UNOnext, they must be
used Daisy-Chain, and the communication mode is Modbus/RTU protocol. It is recommend-
ed to use 22AWG multi-core shielded twisted pair cable or above to achieve the best re-
sults. The simple wiring instructions is below, please use the RS485 adapter include in the
box (Please plug-in on the COM1 of the UNOcentral).
3
UNOnext can directly connect to a controller with RS485 interface, up to 16 devices can be connect-
ed to one controller.
If the UART sengs of UNOnext have been modied, please modify to the default sengs
above before connecng to UNOcentral.
The Modbus slave address of UNOnext can be set by dip switch following below table. Oth-
ers detail UNOnext sengs can be referred the UNOnext user manual. Table 2 Set Modbus slave
address of UNOnext
The UART conguraons of the UNOcentral and UNOnext
Baud Rate: 9600
Data-bit: 8
Parity: None
Stop-bit: 1
4
1. Prepare tools and connector.
2. Connect signal lines.
3. Tighten the screws 4. Need to fix the plastic sheet.
Step of operation.
5
5. Close the lid
6. Install connector on the COM1 of UNOcentral
6
7. Connect the HDMI cable, mouse, and keyboard to the screen to confirm that the number of
UNOnext is the same as the number and sensor data are shown on the screen.
If the sensor data does not show value at all or the number of devices is incorrect, please
check below checklists
◇Are all UNOnext power on?
◇Is RS485 wiring problem?
◇Do use the wrong pin hole?
◇Does follow RS485 installation guideline?
◇All of UNOnext should be used different modbus slave address.
Table of contents
Other Delta Measuring Instrument manuals
Delta
Delta DPM-C320 User manual
Delta
Delta DPM-D510 User manual
Delta
Delta DPM-C530 User manual
Delta
Delta MessageMaxx DMS-279 Manual
Delta
Delta EMS 32-011 User manual
Delta
Delta R4E User manual
Delta
Delta XVR5432L-I2 User manual
Delta
Delta LTL-XL User manual
Delta
Delta DVP-ES2 User manual
Delta
Delta UNO-C07X011 User manual
Delta
Delta UT-191T User manual
Delta
Delta DPM-MA1121 User manual
Delta
Delta LTL3000 User manual
Delta
Delta CS-LDM-50M User manual
Delta
Delta LD-100E-M22 User manual
Delta
Delta LTL-XL User manual
Delta
Delta REVEZ-HD-TRIO DVB-T/T2 User manual
Delta
Delta RetroSign GRX-1 User manual
Delta
Delta TECK II User manual
Delta
Delta DVP04TC-H2 User manual
