Da-Lite Senior Electrol User manual

INSTRUCTION BOOK FOR

Senior Electrol®

Pre-Installation

Installation

1. Carefully unpack screen and remove outer wrapping

from case.

2. Remove instruction cover plate (Fig. 1). Do not remove metal

shipping brace (secures roller), wrapping paper, or tape strips

until screen is installed.

3. Make sure to recheck measurement of screen location

before installation.

NOTE: Screen is not centered in box. Screen surface

is set 18⅝" from motor end.

Ironing Board

Senior Electrols 14' wide and over contain an ironing board to

latten the fabric (long strip attached). The ironing board is part

of the screen case. Do not remove. Contact Da-Lite if the ironing

board is in need of adjustment. (Fig. 2).

Hangers (If required)

1. Make sure one hanger is approximately 25" from end

of case (motor end).

2. Make sure second hanger is approximately 11 ½" from

opposite end of case.

3. Place a third hanger on the center line of fabric.

4. On screens equipped with an ironing board, make sure

hangers do not interfere with the ironing board brackets.

5. Make sure hanger used on motor end does not interfere

with motor access door.

Figure 2

Hex Head

Screws Tape Strip

Shipping

Brace

(Not on 3"

Roller) Ironing

Board

Wall Type Hanger

Picture

Surface

Picture

Surface

Picture Surface

Ceiling Type

Hanger

Rafters

Wall or Ceiling Mount With Hangers

Wall Type Hangers with ceiling hanger adapters are

standard equipment. For wall type, use wall hanger only.

For ceiling type installation, use the wall type hanger and

ceiling adapters as shown in Fig. 3 on page 4.

Recessed Above Ceiling

Other methods of installation will no doubt

suggest themselves especially in new buildings

where it would be an easy matter to provide a

recess for the screen to conceal it when not in use.

Do Not Seal In-Allow Access.

For Exposed Installation

If the screen is to be mounted in an exposed

position, it may be covered with inished plywood,

veneer paneling, plastic wall covering or a valance.

Figure 1

Instruction Cover

Case

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

Save These Instructions

Installation

Screen Adjustment

NOTE: Unit is not to be installed in air handling space.

1. Level unit lengthwise with a carpenter's level and plum

level.

CAUTION! Do not completely seal in unit. Access

room must be allowed for motor repair or fabric

replacement.

ATTENTION! Ne ixez pas complètement l'unité. Un

espace doit être laissé pour pouvoir réparer le

moteur ou remplacer la toile.

2. Remove shipping brace by removing 3 hex head screws

(Fig. 2).

CAUTION! Do not cut wrapping paper or tape with

knife or any sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le papier d'emballage ou

le ruban adhésif avec un couteau ou un outil

tranchant. Retirez à la main.

3. Remove wrapping paper and tape strips (Fig. 2).

4. Install electrical hook up that applies to your unit. Make

sure to review your Electrical Installation Checklists and

wiring diagrams (included) for either 120 volt switch,

220/240 volt switch, or DRC low voltage control. Unit

should be installed by a qualiied electrician.

NOTE: Must be installed in accordance with the

requirements of the Local Building Codes, the Canadian

Electrical Code (CEC), CAN/CSA C22.1 and the National

Electric Code (NEC), NFPA 70.

5. Test installation by carefully running surface up and

down several times. Be prepared to stop screen.

6. Check for satisfactory condition by running screen a

few times.

NOTE: The picture surface, when rolled down, should

have a full wrap around the roller. Do not allow any part

of the roller to become exposed.

Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite.

Should it be necessary to adjust for more or less drop of picture (viewing area), proceed in the following manner:

More Screen Drop

1. Place operating switch in “down” position.

2. When the screen stops, turn the “down” limit knob one-

quarter turn clockwise.

3. Test by raising picture surface approximately two feet, then

lower again. Repeat until desired drop is attained.

CAUTION! When screen is in bottom position, do not

adjust for more than 3" of additional drop. Roller should

not be exposed.

ATTENTION! Lorsque la surface de projection est sur la

position "Bas", ne déroulez pas la toile plus de 7,6 cm (3

po). N'exposer aucune partie du rouleau.

Less Screen Drop

1. Raise picture surface approximately two feet above desired

level.

2. Place operating switch in “of” position.

3. Turn the “down” limit knob one-quarter turn

counterclockwise.

4. Test by raising and lowering picture surface.

5. Repeat steps 3 and 4 until desired drop is attained.

NOTE: Limit “down” switch knob controls stopping point of

picture surface in bottom position.

Limit “up” switch knob controls stopping point of picture surface

inside case.

Picture Surface Rolled Up Or Closed Position

Senior Electrol®Instructions

NOTE: Adjustments should not be necessary to screen in the rolled up or closed position. If necessary, use the following procedures:

Picture Surface Rolls Too Far Into Case

1. Lower picture surface approximately two feet with operating

switch.

2. Place operating switch in “of” position.

3. Turn the “up” limit knob one-quarter turn clockwise.

4. Press operating switch to raise picture surface. Repeat operation

if picture surface continues to roll too far into case.

Picture Surface Does Not Roll Completely Into Case

1. Place operating switch in “up” position.

2. Turn the “up” limit knob one-quarter turn counterclockwise.

3. Test by lowering picture surface approximately two feet with

operating switch, then raise picture. Repeat operation if desired

position is not reached.

Raise Lower Raise Lower

Down Up

Side View

End View

Bottom View

Outlet

Box

Suggested

Slot Width

Picture Surface

Wall Or Ceiling Type Hanger

Hinged Access Panel In Bottom (For All Wiring & Adjustments)

Length A = Fabric Width “B“

Plus 23" All Sizes

NOTE: Install This Bracket

For Ceiling Type Hanger Only

10" Overall Width

Of Bracket

¾" Diameter

Holes

⅜" Nut & Bolt

2 ⅞"

2⅞"

3 ¾"

⁄"

⅞"

9 ½"

3 ¾"

4 ⅜

Figure 3

9 ½ ± ¼

“

B“

18 ⅝

12 ⁄

11 ⅜ ± ⁄

“

A“ ±¼

8 ±¼

12 ⁄

Senior Electrol®Instructions

Senior Electrol®Installation

4 ⅜"

For Screens Up To 18' X 18'

Motor Compartment

Reinforced

Top

11 ⁄"

18 ⅝" Hinged Access Panel

For Motor Compartment

Fabric Height x Width As Ordered,

Up To 18 Feet x 18 Feet

Length = Fabric Width

+ 23", All Sizes

4 ⅜"

10 ¾" Reinforced

Top

18 ⅝" Hinged Access Panel

For Motor Compartment

Fabric Height x Width As Ordered,

Up To 20 Feet x 20 Feet Or

Up To 12 Feet High x 24 Feet Wide

Motor Compartment

12 ⁄"

For Screens 20' And Larger In Height Or Width

Length = Fabric

Width + 23", All Sizes

9 ½"

Up Limit Switch

Down Limit Switch

Black

(Down)

Red (Up)

Black

(Down)

Capacitor

Red (Up)

White

(Common)

Adj.

Down

Adj.

White

Black With Yellow

Down

Of

Internal

Wiring

External Wiring

To Be Completed

By Installer

Red

Green

(Ground) Motor: 120V. 60 Cycles

1/10HP Intermittent Duty

With Auto-Reset Thermal

Protector

Junction Box, Mounted In

Screen Case, In Which Internal

Wiring Terminates In White,

Black and Red Leads.

In Multiple Control Installations

This Switch Is Replaced By The

Low Voltage Control, Operated

From Push Button Stations.

Operating Switch, Switch Box,

And Plate Furnished With Screen.

(SPST With Center Of)

AC Common

AC HOT

120 Vac 60 Hz 1 Amp. Max.

Side View Of

Switch & Box

120V Wiring Diagram

240 Volt Wiring Diagram

For Standard Wall Switch:

Da-Lite ofers two styles of 240 volt wall

switches for standard operation. Please see

wiring diagram included in wall switch box

included with screen.

BlackRed

Troubleshooting

Symptom Cause Solution

Screen will not operate

and motor does not hum.

Blown fuse. Replace fuse.

Tripped circuit breaker. Reset circuit breaker.

Improper wiring to operating switch.

Tighten all loose wire connections. Correct any improper

connections. Check for power.

“Down” Position

Check for power across black and white leads.

“Up” Position

Check for power across red and white leads.

Improper wiring to junction box in screen.

“Down” Position

Check for power at black and white leads.

“Up” Position

Check for power at red and white leads.

Thermal overload tripped (excessive overheating). Let motor cool down for 15 minutes. Try again.

Burned out motor winding.

Disconnect motor leads and check for continuity between

black and white wires for “down” position. Check for

continuity between red and white wires for “up” position.

Replace gear motor if either combination shows an open

circuit.

Defective limit switch

Disconnect “down” limit switch from circuit. Check for

continuity. Switches are normally closed and open on

contact.

Motor hums.

Temporary binding. With power “o,” turn roller by hand to free binding.

Shipping bracket not removed. Remove shipping bracket and wooden wedge.

Defective capacitor. Replace capacitor.

Visit www.da-lite.com to ind installation and troubleshooting

tutorials. You will also ind a link to Live Chat for interactive

support and you can contact us by email at

info@da-lite.com or by phone at (800) 6223737 or (574) 2678101

with any troubleshooting questions.

Troubleshooting

Symptom Cause Solution

Screen will not move “up.”

Motor does not hum.

Motor hums.

Blown fuse or tripped circuit breaker. Replace fuse or reset circuit breaker.

No power between red and white leads

in junction box. Correct improper wiring.

Thermal overload tripped. Let motor cool for 15 minutes. Try again.

Burned out motor winding. Check for power between red and white motor leads.

Replace motor if there is power.

Temporary binding. With power o, turn roller by hand to free binding.

Burned out capacitor. Replace capacitor.

Broken wire or loose connection in “up”

position circuit. Secure connection or replace wire.

Scraping or grinding noise. If metal shipping bracket is left attached to screen,

it may be rubbing on motor end of roller. Remove shipping bracket.

Gear noise. Gear may need lubrication. Apply grease.

Fabric rubbing.

Normal condition.

NOTE: Screens with ironing boards have fabric

that drags across the board.

Incorrect stopping point in

upward position.

Lost roller wrap. Lift bottom edge up and over roller.

Limit switch out of adjustment. See installation instructions.

Incorrect stopping point in

downward direction.

Lost roller wrap. See above.

Limit switch out of adjustment. See installation instructions.

Inconsistent stopping points.

Limit switch travel plate not moving.. Tighten set screws located on nylon gears

(drives limit switch).

Excessive end play in lead screw of limit

switch assembly.

Tighten nut between adjusting knobs.

Tighten lead screw of limit switch.

Screen does not stop going

up or down.

Limit switch assembly paddle damaged

or is out of place.

Remove and check limit switch assembly.

Repair or replace as necessary.

LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,

Warsaw, IN 465810137, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

46490

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0255 (Rev. 3) 11.14

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite DescenderPro User manual

Da-Lite

Da-Lite Designer Contour Manual User manual

Da-Lite

Da-Lite DESIGNER CONTOUR MANUAL User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite TENSIONED PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Da-Lite

Da-Lite Multi vision imager User manual

Da-Lite

Da-Lite MULTI-MASK IMAGER User manual

Da-Lite

Da-Lite DELUXE MODEL B User manual

Da-Lite

Da-Lite Da-Snap 74610 User manual

Da-Lite

Da-Lite Ascender Electrol User manual

Da-Lite

Da-Lite senIor electrol User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Contour Electrol User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL User manual

Da-Lite

Da-Lite Viewshare Advantage Electrol User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Boardroom ElEctrol User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Contour Electrol User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions