Da-Lite Da-Snap 74610 User manual
POWER
PRESENTATION PRODUCTS
The
In
Instruction Book For
Da-Snap Screen
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574/267-8101
800-622-3737
Fax: 574/267-7804
http:// www.da-lite.com
e-mail: [email protected]
1
WALL BRACKET
Quantities vary by screen size
Screens smaller than 80" viewing width = 1
Screens 80" to 96" viewing width = 2 QUANTITY INCLUDED __________
Screens over 96" viewing width = 3
Installation screws not included
LOWER WALL BRACKET
Quantity of 1. Only for screens
smaller than 80" viewing width QUANTITY INCLUDED __________
Installation screws not included
SNAP STUD
QUANTITY INCLUDED ________
#10 SCREW
QUANTITY INCLUDED ________
FRAME BRACKET
Quantities vary by screen size
Screens smaller than 80" viewing width = 3
Screens 80" to 96" viewing width = 4
Screens over 96" viewing width = 6
QUANTITY INCLUDED ________________________________
HIGH POWER FRAME BRACKET
Screens with High Power viewing surface quantity = 1
Screens with 2-piece side frame rails quantity = 2
QUANTITY INCLUDED ________________________________
2
1. Unpack the frame parts from the carton. DO NOT
unroll the screen surface at this time.
2. Take care to observe the color code on the parts.
Assemble the top and bottom frame members on the
left and right sides using the #10 black screws and
snap studs. See figure 1.
FRAME ASSEMBLY
FIGURE 1. REAR VIEW
SNAP STUD
SIDE
#10 BLACK SCREW
SIDE
TOP
BOTTOM
SNAP STUD
There are four methods of installation based on the size
of the screen and type of viewing surface. Measure the
width of the viewing area of your screen and refer to the
appropriate method of installation below. The hanger
bracket diagram shows the type and quantity of bracket
that is supplied based on the size of the screen.
Method 1: Screens smaller than 80" in viewing width.
Method 2: Screens 80" to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
Method 4: Any size screen with High Power viewing
surface.
Method 1
1. Use the supplied #10 screws to attach three frame
brackets to the back of the frame as shown in figure
2.
INSTALLATION
2. Secure the wall bracket to wall studs at the desired
height. Make sure the bracket is level. The top of the
frame will be 1/8" above the top of the wall bracket
when mounted. You will need at least 5/8" clearance
above the bracket to hang the screen.
3. To install the lower wall bracket, you must measure
the overall height of the screen frame and subtract
1-3/8". Using that dimension, measure down from the
top edge of the wall bracket and mark the wall for
two screw holes. The holes should be centered
within the frame and 6" apart. Refer to figure 3.
4. Attach the lower wall bracket to the wall. Refer to
figure 4 for proper orientation. Do not tighten the
screws completely. The bracket should slide up and
down easily.
5. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the inside of
the roll. Place the frame over the screen surface, and
while lifting the frame with one hand, snap the
screen surface onto the frame with the other hand
while maintaining a steady pull on the surface.
6. Hang the screen on the brackets by hooking the
bottom of the frame onto the lower wall bracket and
lift up until you can hook the top of the frame on the
top bracket. Push down on the frame to seat it on the
brackets. Refer to figure 4.
FIGURE 2
FRAME BRACKETS
3-PIECES
#10 SCREWS
6-PIECES
WALL BRACKET
1-PIECE
LOWER WALL BRACKET
1-PIECE
FIGURE 3
OVERALL HEIGHT - 1-3/8"
OVERALL
HEIGHT
6"
FIGURE 4
2
LIFT
3
1
WALL
3
Method 2
1. Use the supplied #10 screws to attach four frame
brackets to the back of the frame as shown in
figure 5.
2. Secure the wall bracket to wall studs at the
desired height. Make sure the bracket is level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.
3. To install the lower wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See figure 6.
4. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.
5. Position the screen with the attached surface
onto the top wall bracket as shown in figure 7.
Push down at the center of the bottom frame rail
to hook onto the lower wall bracket.
Method 3
1. Use the supplied #10 screws to attach six frame
brackets to the back of the frame as shown in
figure 8.
2. Secure the wall brackets to wall studs at the
desired height. Make sure the brackets are level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.
3. To install the lower wall bracket, you must
measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See figure 6.
4. Some large screen sizes are made with 2-piece
side frame rails. For this type of frame you will
need to attach one High Power bracket to each
side at the joint. See figure 8.
FIGURE 5
FRAME BRACKETS
4-PIECES
#10 SCREWS
8-PIECES
WALL BRACKET
2-PIECES
FIGURE 6
OVERALL HEIGHT -1/4"
OVERALL HEIGHT
WALL
INSTALLATION
2
1
WALL
FIGURE 7
FIGURE 8
FRAME BRACKETS
6-PIECES
#10 SCREWS
12-PIECES
WALL BRACKETS
3-PIECES
HIGH
POWER
BRACKET
FOR
LARGE
SPLIT
FRAMES
ONLY.
2-PIECES
4
INSTALLATION
5. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.
6. Position the screen with the attached surface
onto the top wall bracket as shown in figure 7.
Push down at the center of the bottom frame rail
to hook onto the lower wall bracket.
7. If you attached brackets to the side frame rails in
step 4, anchor these to the wall with an
appropriate fastener for your type of wall.
Method 4
1. Use the supplied #10 screws to attach two frame
brackets and two High Power brackets to the
back of the frame as shown in figure 9.
2. Secure the wall bracket to wall studs at the
desired height. Make sure the bracket is level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.
3. Unroll the screen on a clean surface. Do not use
newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.
4. Position the screen with the attached surface
onto the top wall bracket as shown in figure 7.
Push down at the center of the bottom frame rail
to tension the fabric. Mark the screw holes for
the bottom brackets. Drill holes in wall and attach
the brackets to the wall with screws.
CLEANING
Da-Tex, Dual Vision, Pearlescent, Cinema Vision, High
Power, Da-Mat, High Contrast Da-Mat, Audio Vision, High
Contrast Audio Vision, High Contrast Cinema Vision and
High Contrast Cinema Perf surfaces can be cleaned as
follows:
Using a white clean cloth (100% cotton preferred)
that is dampened with clear water, gently wipe the
area in one direction. Do not use a circular motion.
Using a dry 100% cotton cloth, wipe dry after each
cleaning session. To clean a stubborn stain or a
sticky surface, use denatured alcohol (methanol or
methyl alcohol) following the same procedure as for
water. For extremely stubborn stains, use V M & P,
Naphtha or Super Naphtha and follow the same
procedure as for water.
FIGURE 9
FRAME BRACKETS
2-PIECES
#10 SCREWS
8-PIECES
WALL BRACKET
1-PIECE
HIGH POWER BRACKET
2-PIECES
5
Printed in U.S.A. 75135 Rev. 1/03
Table of contents
Other Da-Lite Projection Screen manuals
Da-Lite
Da-Lite UTB Contour User manual
Da-Lite
Da-Lite Deluxe Insta-theater User manual
Da-Lite
Da-Lite HORIZON ELECTROL User manual
Da-Lite
Da-Lite Cinema Contour Screen User manual
Da-Lite
Da-Lite PROFESSIONAL ELECTROL User manual
Da-Lite
Da-Lite ADVANTAGE ELECTROL User manual
Da-Lite
Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual
Da-Lite
Da-Lite EXECUTIVE ELECTROL User manual
Da-Lite
Da-Lite ViewShare Advantage Electrol Retrofit User manual
Da-Lite
Da-Lite Da-Snap 79982 User manual
Da-Lite
Da-Lite DescenderPro User manual
Da-Lite
Da-Lite Whiteboard Mount User manual
Da-Lite
Da-Lite PROFESSIONAL ELECTROL User manual
Da-Lite
Da-Lite TENSIONED COSMOPOLITAN ELECTROL User manual
Da-Lite
Da-Lite Versatol User manual
Da-Lite
Da-Lite Ascender Electrol User manual
Da-Lite
Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual
Da-Lite
Da-Lite DELUXE MODEL B User manual
Da-Lite
Da-Lite DESIGNER CONTOUR MANUAL User manual
Da-Lite
Da-Lite Tensioned Director Electrol User manual
Popular Projection Screen manuals by other brands
FART PRODUKT
FART PRODUKT Standard SCREEN Installation instruction
Draper
Draper E Series Installation & operating instructions
Elite Screens
Elite Screens Elite Tripod Series user guide
Laarhoven
Laarhoven Companion II General assembly instructions
Renogy
Renogy RMS-LFPS-US manual
Samsung
Samsung S*H65* user manual
