Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

INSTRUCTION BOOK FOR

Large Advantage®

Deluxe Electrol®

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any appliance is used by

or near children. Do not leave appliance unattended while in

use.

3. Do not operate appliance with a damaged cord or if the

appliance has been dropped or damaged – until it has been

examined by a qualiied serviceman.

4. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

5. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

6. To reduce the risk of electric shock, do not immerse this

appliance in water or other liquids.

7. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

8. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of ire, electric shock, or

injury to persons.

Save These Instructions

Tools Required for Installation

Pre-Installation

#2 Phillips Screwdriver 3/4“ Open Wrench

or Socket Driver

1. Carefully unpack case from shipping crate.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam from case.

5. If necessary. adjust hanger brackets with a 3/4" open wrench

or socket driver.

Ironing Board

The Large Advantage Electrol includes an ironing board to latten

the fabric (long strip attached). The ironing board is part of the

screen case. Do not remove. Contact Da-Lite if the ironing board

is in need of adjustment. (Figure 1).

Ironing

Board

Figure 1

The case has a self-trimming lange around the bottom. Ceiling tiles or drywall may be placed on top of this lange to provide a inished

appearance.

1. The case provides multiple attachment points for bolts, cables,

or threaded rod. Page 5 shows threaded rod installed. The

variable position-mounting bracket may be located anywhere

along the length of the case. It is recommended to keep the

brackets spaced evenly enough to distribute the weight of the

screen. One mounting bracket is required for every 4' of case

length.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, screen assembly must be level

after installation.

3. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box

cover and secure with 2 screws.

NOTE:

Motor Operator Projection Screen Models LADT,

LADDT, LAD and LADD must be installed in accordance with the

requirements of the Local Building Codes, the Canadian

Electrical Code (CEC), CAN/CSA C22.1 and the National Electric

Code (NEC), NFPA 70. An appropriate disconnect device shall be

provided as part of the building installation.

If your case was ordered in advance of the screen and roller

assembly, your installation is now complete. Continue to step

4 if your Large Advantage Deluxe Electrol was ordered as a

complete unit.

4. Carefully remove paper and tape from roller assembly

Caution! Do not use a knife or sharp object to cut tape;

you will damage the screen. Pull orange string.

ATTENTION! Ne coupez pas le ruban adhésif sur la toile

avec un couteau ou un outil tranchant. Tirez sur le cordon

orange.

5. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 1 minute on and 3 minutes of.

Case Installation

Installation

(Suggested) ½"

Threaded Rod (Not

Included) Attached

To Mounting

Bracket

Finished

Ceiling

Self-Trimming

Flange

9 ⅛"

13 ⅛"

12 ⁄"

11 ⁄"

11"

Door Roller

Screen

Roller

Closing Door

Access Door

Audience

Side

Self-Trimming

Flange

2 ⁄" 10 ⁄"

Variable

Position

Mounting

Brackets

Electrical

Junction

Box

8 ½"

11 ½"

Case Length

11"

Screen And Roller Assembly Installation

If your screen was shipped with the motor and roller already installed proceed to step 7.

1. Remove four bolts from ends of door assembly (2 bolts on

each end) (Fig. 2). This will allow the door assembly to drop

open for access to case. For larger sizes, you will also need

to remove the door support screws.

2. Carefully unpack screen and roller assembly. Leave packing

paper on the roller.

3. Remove the square peg bracket from the motor end of the

roller assembly.

4. Remove the safety clip from the motor attachement bracket

located in the motor end of the screen housing.

5. Place the roller assembly into the case with the motor on the

left side. The limit switches should be facing down. Line up

the head of the motor with the motor attachment bracket.

6. Loosen four bolts that secure pin end mounting bracket into

housing. Lift pin end of roller into position and slide the

bracket into the roller pin. Tighten all four bolts.

7. Complete electrical hook-up by snapping motor 1/3 wire

connectors into case connectors.

8. Return to motor end and insert safety clip over casting

bracket to secure motor end.

CAUTION! Do not cut tape on fabric with a knife or any

sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le ruban adhésif sur la toile

avec un couteau ou un outil tranchant. Retirez à la main.

9. Carefully remove tape strips securing picture surface around

roller. Slat should move freely (Fig. 3). (Only if the roller

assembly is pre installed.)

10. Test installation by operating the screen several times. Be

prepared to stop the screen. The door assembly will not

close until the wall switch is placed in the up position and

when the screen motor stops at its limit switch in the up

direction.

NOTE: Unit duty cycle is 1 minute on, 3 minutes of.

NOTE: Excessive continuous operation may cause the motor

to overheat. If this happens the motor will shut of until it

cools to a normal operating temperature.

11. Close door assembly and replace four bolts at ends of door

(2 bolts on each end) (Fig. 2).

Figure 3`

Dual Motor LVC

Control Box

Screen Motor

Limit Switches

Screen Motor

Door Motor

Limit Switches

Door Motor

Access Door

Assembly

Figure 2

Door Support Screws

(Not All Sizes)

Access

Door

Bolts

Surface travel is stopped automatically in the fully opened and

closed positions by limit switches that are properly adjusted at

Da-Lite. Should it be necessary to adjust for more or less drop of

picture, proceed in the following manner:

NOTE: Use a screw driver or 5/32" Allen wrench to make

adjustments.

More Screen Drop

1. Place operating switch in “down” position.

2. When the screen stops, turn the white “down” limit knob

(Fig. 3) one-quarter turn counterclockwise. Test by raising

picture surface approximately two feet, then lower again.

Repeat until desired picture surface position is attained.

CAUTION: Do not adjust for more drop than what was

ordered. At least 11/2 wraps of fabric must remain on the

roller. This screen comes standard with 0" or 2" black at

the top. See the speciication data sheet for details.

ATTENTION! N'efectuez pas de réglage pour obtenir un

déroulement supérieur à celui commandé. Au moins 1 à

1/2 tour de toile doit être maintenu sur le cylindre. Cet

écran est doté de série d'une bande noire supérieure de 0

cm (0 po) ou 5 cm (2 po). Consultez la iche technique

pour plus de renseignements.

Less Screen Drop

1. Raise picture surface approximately two feet above

desired level.

2. Place operating switch in “of” position.

3. Turn the white “down” limit switch (Fig. 2) one-quarter turn

clockwise. Test by raising picture surface approximately two

feet, then lower again. Repeat until desired picture surface

position is attained.

Contact Da-Lite at 8006223737 if door motor needs

adjustment.

Screen Adjustment

Access Door

Assembly

120V Wiring Diagram

NOTE: 2024 AWG wire recommended for connecting

wall switch to dual motor controller.

CAUTION: Do not use 3-position high voltage

rocker switch with this unit! This will damage

the low voltage control board.

ATTENTION: N'utilisez pas un interrupteur à

bascule à 3 positions pour circuit à haute tension

avec cette unité. Cela endommagera le tableau de

contrôle basse tension.

Power Input

120VAC / 60HZ

DOWN

STOP

White

(Common)

White

(Common)

White (Common)

Black

(Down)

Red

(Up)

Screen

Motor

Red

(Up)

White

(Common)

Black

(Down)

Front of

Wall

Switch

Back of

Wall

Switch

Green

(Ground)

Black

(Down)

Red

(Up)

Green

(Ground)

Door

Motor

Dual Motor Control Board

White

(Common)

Black (Down)

Red (Up)

Green (Ground)

Green

(Ground)

Black

(Hot)

Not Used

"Eye" Port

Plug "IR" or "RF"

Remote Here

240V Wiring Diagram

NOTE: 2024 AWG wire recommended for connecting

wall switch to dual motor controller.

CAUTION: Do not use 3-position high voltage

rocker switch with this unit! This will damage

the low voltage control board.

ATTENTION: N'utilisez pas un interrupteur à

bascule à 3 positions pour circuit à haute tension

avec cette unité. Cela endommagera le tableau de

contrôle basse tension.

Blue (Common)

Front of

Wall

Switch

Back of

Wall

Switch

Brown (Down)

Black (Up)

Green / Yellow (Ground)

"Eye" Port

Plug "IR" or "RF"

Remote Here

Power Input

240VAC / 50HZ

DOWN

STOP

Brown

(Hot)

White

(Common)

Blue

(Common)

Brown

(Down)

Black

(Up)

Green / Yellow

Ground)

Screen

Motor

Red

(Up)

Black

(Down)

Not Used

Door

Motor

Dual Motor Control Board

Blue

(Common)

Green / Yellow

Ground)

Blue

(Common)

Brown

(Down)

Black

(Up)

Green / Yellow

Ground)

Troubleshooting

Symptom Cause Solution

Screen will not operate or will

not go “down”.

Motor does not hum.

Motor hums.

Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage,

rewire incoming electric line.

Blown facility fuse. Replace facility fuse.

Tripped facility circuit breaker. Reset facility circuit breaker.

No power to operating switch

or junction box.

Check above. Tighten all loose wire connections.

Recheck wiring. See installation instructions.

Low voltage board has no power or

blown transformer.

Replace low voltage board.

"Down" Position

Check for power across black and white leads.

Power at junction box.

Thermal overload tripped. Let motor cool down for 15 minutes. Try again.

Broken wire in the “down” position. Check for continuity.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Capacitor burned out. Replace motor assembly.

Screen will not move upward.

Motor does not hum.

Motor hums.

Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage,

rewire incoming electric line.

Blown facility fuse. Replace facility fuse.

Tripped facility circuit breaker. Reset facility circuit breaker.

No power to operating switch or junction box. Check above. Tighten all loose wire connections. See above.

Low voltage board has no power or

blown transformer.

Replace low voltage board.

"Up" Position

Check for power across red and white leads.

Open door limit switch. Replace switch.

Power at junction box.

Thermal overload tripped. Let motor cool down for 15 minutes. Try again.

Broken wire in the “up” position. Check for continuity.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Capacitor burned out. Replace motor assembly.

Visit www.da-lite.com to ind installation and troubleshooting

tutorials. You will also ind a link to Live Chat for interactive

support.

You can contact us by email at info@da-lite.com or by phone

at 800.622.3737 or 574.267.8101 with any additional

troubleshooting questions.

Other manuals for LARGE ADVANTAGE DELUXE ELECTROL

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite C with CSR User manual

Da-Lite

Da-Lite ASCENDER ELECTROL User manual

Da-Lite

Da-Lite Tensioned Conference Electrol User manual

Da-Lite

Da-Lite Da-Snap Screen User manual

Da-Lite

Da-Lite DesIgner Contour Manual User manual

Da-Lite

Da-Lite Wireline Advantage User manual

Da-Lite

Da-Lite Parallax Thin User manual

Da-Lite

Da-Lite TENSIONED COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Model B User manual

Da-Lite

Da-Lite Model C User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite electrol User manual

Da-Lite

Da-Lite Theater-lite User manual

Da-Lite

Da-Lite SLIMLINE ELECTROL User manual

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol Series User manual

Da-Lite

Da-Lite MULTI-MASK IMAGER User manual

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite Multi vision imager User manual

Da-Lite

Da-Lite DESIGNER CONTOUR ELECTROL Series User manual

Da-Lite

Da-Lite ExecutiveElectrol User manual

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions