Da-Lite EXECUTIVE ELECTROL User manual

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574/267-8101

800-622-3737

Fax: 574/267-7804

http:// www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

EXECUTIVE®ELECTROL®

PRE-INSTALLATION

1. Carefully unpack screen and remove outer wrapping from case.

2. Remove fabric and cardboard strips from access door.

3. Remove access door by gently prying from middle section.

4. FOR TYPE 3 INSTALLATION ONLY, remove wood strips along bottom edge of screen case.

5. Remove instruction cover (Fig. 1). Remove, reverse, and remount Center Support Brackets.

6. Do not remove metal shipping brace (secures roller), wrapping paper or tape until screen is installed.

NOTE: Screen is not centered in box. Screen is set 22" from motor end.

7. Make sure to recheck measurement of screen location before installation.

INSTALLATION

1. Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting

bracket. Secure opposite end. Support center of the screw using the brackets.

2. Level unit lengthwise with a carpenter’s level and a plum level.

CAUTION! DO NOT SECURE ACCESS DOOR OR SEAL IN UNIT UNTIL SCREEN HAS BEEN SECURED IN POSITION AND PROP-

ERLY TESTED FOR SATISFACTORY OPERATION. DO NOT FIT UNIT SO TIGHTLY THAT THE SCREEN SURFACE DROP DOOR BINDS.

DOOR DROPS BY GRAVITY ONLY.

3. If you are going to cover screen door with paneling or other materials, allow access (suitable holes or a plug) to

screws when servicing.

4. Remove shipping brace by removing 3 hex head screws (Fig. 2).

CAUTION! DO NOT CUT WRAPPING PAPER OR TAPE WITH KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.

5. Remove tape strips and release fabric (Fig. 2). Picture surface should hang freely (Fig. 3). Remove any tape left

hanging on back of fabric. Bottom edge should be positioned between bottom edge of case and center of roller.

▲

CASE

INSTRUCTION COVER

FABRIC DOOR

ACCESS DOOR

FIG.1 FIG.2

SHIPPING BRACE

(NOT ON 3" ROLLER)

HEX HEAD

SCREWS

TAPE STRIP

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be

used. Cords rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized service dealer

when repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subse-

quently.

5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric

shock, or injury to persons.

SAVE THESE INSTRUCTIONS

SCREEN ADJUSTMENT

The picture surface drop, and the opening and closing of the fabric door, are controlled automatically by limit switches

which have been preset at Da-Lite. When the picture surface is moving upward, it is controlled by a limit switch that

shuts off when the door closes. To adjust for more or less picture drop (viewing area), proceed in the following manner:

SCREEN UNROLLED IN “DOWN” OR “BOTTOM” POSITION.

NOTE: Limit switch knob labeled DOWN controls point of picture surface in bottom position. Limit switch knob labaeled DOOR con-

trols the synchronization of the door opening or closing. Do not adjust!

MORE SCREEN DROP

1. Place operating switch in “down” position.

2. When the screen stops, turn the “down” limit knob one turn at a time

clockwise, until the desired picture surface position is attained. Test

by raising picture surface approximately two feet, then lower again.

Repeat until desired picture surface position is attained.

CAUTION! WHEN PICTURE SURFACE IS IN “BOTTOM” POSITION, DO NOT

ADJUST FOR MORE THAN 3" OF ADDITIONAL DROP. DO NOT ALLOW ANY

PART OF THE ROLLER TO BECOME EXPOSED.

LESS SCREEN DROP

1. Raise picture surface approximately two feet above desired level.

2. Place operating switch in “off” position.

3. Turn the “down” limit knob one turn at a time counter-clockwise.

4. Place operating switch in “down” position. Repeat steps 2 and 3 until desired position is attained.

▲

ACCESS DOOR INSTALLATION

1. Press switch “down” so that fabric door opens (Fig. 3).

2. Remove screws (2) located on each bumper bracket.

NOTE: The access door is slotted on one edge, permitting the grooved section to fit over the support clips on inside of case.

3. Place access panel so groove can be pushed over clips. Holes in access panel brackets should align with bumper

bracket holes.

4. Replace screws.

5. Make sure there is approximately 3⁄16" clearance around access door. Keep paint, plaster, tile or mastic out of hinge.

Fit access panel so it can be removed for maintenance.

NOTE: If picture surface is hanging out of case approxi-

mately 12”, a wrap of the picture surface has been lost

from around the roller; see, “Restoring Roller Wrap”.

.6.Install electrical hook up that applies to your unit.

7. Test installation by carefully running picture sur-

face “up” and “down” several times. Be prepared

to stop screen.

8. Make sure picture surface, when rolled down, has

a full wrap around roller. No part of roller should

be exposed. Fabric door and picture surface will

drop simultaneously when switch is pressed

“down”. Door will close simultaneously with pic-

ture surface as picture surface rolls into case.

FIG.3

3 1/2"

12 1/16"

9 1/2"

2 3/16"

4 1/2"

FALSE TOP

MOUNTING

BRACKETS

3/16" THICK

22"

LENGTH OF FABRIC WIDTH

+ 26 1/2", ALL SIZES

“L” BRACKET

ELECTRICAL

OUTLET

FABRIC

HEIGHT x WIDTH

AS ORDERED, UP

TO 16' x 16'

SUGGESTED METHODS OF INSTALLATION

TYPE 1 & 2

Offset mounting, recessed above ceiling,

for plaster, dry wall or paneling. Door painted

same finish as ceiling.

TYPE 1 & 2

Allow 1/8" min. clearance all around surface door.

Flush mounting, recessed above ceiling. For

use with 1/4" max. paneling or installation in exist-

ing ceiling using molding around door.

TYPE 3

Allow 1/4" min. clearance all around surface door.

Extended mounting, recessed above ceiling.

For use with acoustical or other ceiling tile 3/4"

thick laid over door.

NOTE: Paint the same as

doors and ceiling or

remove and replace

with ceiling tile.

INCLUDING MOUNTING BRACKETS

9 7/8"

9 1/2"

CEILING TILE

3/4"

3/8" APPROX.

12 1/16"

FILLER

BLOCK

3/4"

FALSE TOP

1/4" MAX.

4 3/4"

1/8"

2 1/2"

1/4"

PICTURE

SURFACE

MOUNTING

BRACKETS

FALSE TOP

SURFACE DOOR

ACCESS DOOR

3/4"

11 5/16"

1/4" x 1" SCREW

& NUT INSERT

DRYWALL SCREW

“L” BRACKET

EXECUTIVE ELECTROL INSTALLATION

12 1/16"

1/4" x 2"

LAG SCREW

FALSE TOP

SHIM

RESTORING ROLLER WRAP

CAUTION! DO NOT ATEMPT TO RESTORE A LOST WRAP BY ADJUST ING LIMIT SWTICHES!

1. Run fabric all the way down.

2. Run fabric up and stop just before door closes.

3. Remove the access panel (2 screws, Fig. 3).

4. Two people with clean hands must carefully grasp the slat pocket at each end.

5. Gently lift fabric up and ease it over the top of the roller.

CAUTION! BE CAREFUL NOT TO CREASE OR DAMAGE FABRIC.

6. Additional wraps must be restored if screen surface continues to hang beyond bottom of case.

7. Test screen by running fabric up and down several times.

8. Replace access panel.

▲

EXECUTIVE ELECTROL INSTALLATION

BLACK

BLACK (UP)

BLACK

BLUE

# Z97F9036

7.5 UF ± .06%

440 V.A.C.

50/60 HZ

UP LIMIT SWITCH

(OPERATED BY DOOR)

CAPACITOR

BROWN

(DOWN)

DOWN LIMIT SWITCH

SOLENOID SWITCH

COMMON

MOTOR: 220/240V.A.C. 50 HZ 1/10 HP INTERMITTENT

DUTY WITH AUTO-RESET THERMAL PROTECTOR

INTERNAL

WIRING

EXTERNAL WIRING

TO BE COMPLETED

BY INSTALLER

JUNCTION BOX MOUNTED IN

SCREEN CASE, IN WHICH INTERNAL

WIRING TERMINATES IN

BLACK, BROWN, & BLUE.

BLUE

WHITE

BROWN

DOWN

ADJ.

DOWN

IN MULTIPLE CONTROL INSTALLATION

THIS SWITCH IS REPLACED BY

THE LOW VOLTAGE CONTROL.

BROWN/YELLOW

DOWN

OFF BROWN AC HOT

BLUE AC COMMON

220/240V. AC 50HZ.

2 AMP. MAX

BLUE JUMPER WIRE

JUNCTION

BOX

REAR VIEW OF DPDT.

WITH CENTER OFF.

ROCKER

SWITCH

(GROUND) GREEN/YELLOW

BLACK

RED (UP)

BLUE

BLACK

WHITE

RED

UP LIMIT SWITCH

(OPERATED BY DOOR)

CAPACITOR

BLACK

(DOWN)

DOWN LIMIT SWITCH

SOLENOID SWITCH

WHITE (COMMON)

MOTOR: 120V.60 CYCLES 1/10 HP INTERMITTENT

DUTY WITH AUTO-RESET THERMAL PROTECTOR

INTERNAL

WIRING

EXTERNAL WIRING

TO BE COMPLETED

BY INSTALLER

JUNCTION BOX MOUNTED IN

SCREEN CASE, IN WHICH INTERNAL

WIRING TERMINATES IN

WHITE, BLACK AND RED LEADS

WHITE

DOWN

ADJ.

BLACK (DOWN)

RED (UP)

IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS

REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED

FROM PUSH-BUTTON STATIONS

BLACK WITH YELLOW

DOWN

OFF AC HOT

AC COMMON

120V.AC 60HZ.

1 AMP. MAX

SIDE VIEW OF

SWITCH & BOX

GREEN

(GROUND)

BLACK

BLUE

RED

OPERATING SWITCH,

SWITCH BOX, AND

PLATE FURNISHED

WITH SCREEN. (SPDT)

WITH CENTER OFF)

THIS SWITCH CANNOT BE USED WITH L.V.C.

SOLENOID

120V WIRING DIAGRAM

220 / 240V

WIRING DIAGRAM

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate or will not

go “down”.

Motor does not hum.

2. Motor hums.

CAUSE

(a) Blown fuse.

(b) Tripped circuit breaker.

switch.

(d) Improper wiring to junction box in

screen.

NOTE: Use low voltage control (LVC)

electrical checklist for 3-button control.

Defective wall switch.

Defective LVC unit.

(e) Thermal overload tripped (exces-

sive overheating).

(f) Burned out motor winding.

(g) Defective limit switch.

(a) Temporary fabric binding.

(b) Shipping bracket not removed.

SOLUTION

(a) Replace fuse.

(b) Reset circuit breaker.

tions. Correct any improper

connections. Check for power.

“Down” Position

Check for power across black

and white leads.

“Up” Position

Check for power across red and

white leads.

(d) “Down” Position

Check for power at black and

white leads.

“Up” Position

Check for power at red and

white leads.

Shut power “off” at breaker. Remove

wall switch and check for broken or

loose connection. Replace if defective.

Check LVC electrical checklist.

(e) Let motor cool down for 15 min-

utes. Try again.

(f) Disconnect motor leads and

check for continuity between

black and white wires for “down”

position. Check for continuity be-

tween red and white wires for

“up” position. Replace gear motor

if either combination shows an

open circuit.

(g) Disconnect “down” limit switch

from circuit. Check for continuity.

Switches are normally closed and

open on contact. Replace if de-

fective.

(a) With power “off,” turn roller by

hand to free binding.

(b) Remove shipping bracket and

wooden wedge.

TROUBLESHOOTING

SYMPTOM

3. Screen will not move “up.”

Motor does not hum.

Motor hums.

CAUSE

(a) No power between red and

white leads in junction box.

Check LVC. See above.

(b) Thermal overload tripped (acts as

a breaker).

(d) Temporary fabric binding.

(e) Burned out capacitor.

(f) Broken wire or loose connection

in “up” position (red and white

leads).

SOLUTION

(a) Check fuse. Reset circuit breaker.

Correct improper wiring.

(b) Let motor cool for 15 minutes.

Try again.

and white motor leads. Replace

motor if there is power.

(d) With power “off,” turn roller by

hand to free binding.

(e) Replace capacitor.

(f) Secure connection or replace

wire.

4. Screen starts upward and door

closes immediately shutting off

motor.

(a) Defective solenoid limit switch.

Solenoid pin not retracting.

(b) Defective solenoid.

(a) Manually retract pin a few times.

(b) Check for power to the solenoid

terminals. If there is power, re-

place solenoid.

Check blue wire between sole-

noid switch and solenoid. It is

either crimped or broken. Repair

or replace.

6. Clicking noise in each downward

revolution.

(a) Non-energized solenoid.

NOTE: There should be three clicks.

(a) Check for power to solenoid.

(b) Replace solenoid.

7. Loud buzzing noise. (a) Solenoid not fully retracting. (a) Check for foreign object caught

in solenoid. Remove object.

Tighten 4 mounting screws.

Check for pin binding.

8. Door closes on fabric, leaving 15"

to 20" left hanging out.

(a) Lost roller wrap. (a) See installation instructions.

5. Fabric door does not fully open.

Screen runs.

NOTE: Remember, door must open by

gravity.

(a) Door binding. Plaster, paint or ad-

hesive can cause the hinge to

stick.

(b) Case may be put into a bind

during installation.

fabric door on new installations.

(a) Clean hinge and apply oil.

(b) Tighten or loosen lag screws

located on back of case.

TROUBLESHOOTING

SYMPTOM

9. Screen jammed. Will not operate,

motor hums, door open, closing

mechanism detached from door.

CAUSE

(a) Closing mechanism detached

from door, allowing it to jam into

box.

SOLUTION

(a) After securing fabric to roller,

loosen set screws on motor gear

and manually rotate solenoid

assembly back over top of roller

into position, then reattach door.

Match flats on motor drive shaft

to gear set screws and tighten.

10. Scraping or grinding noise. (a) If metal shipping bracket is left

attached to screen, it may be rub-

bing on motor end of roller.

(a) Remove shipping brace.

12. Incorrect down limit switch

setting.

(a) Lost roller wrap.

(b) Limit switch out of adjustment.

(a) See installation instructions.

(b) See door closure and timing

instructions.

13. Door closes and screen contin-

ues to run upward.

(a) Door limit out of adjustment.

(b) Door limit switch is shorted.

(a) Loosen nut holding limit switch.

Rotate adjusting position, then

secure.

(b) Repair short or replace limit

switch.

11. Gear noise. (a) Gear may need light weight

grease.

(a) Apply light weight grease.

Printed in U.S.A. 48707 Rev. 1/04

Other manuals for EXECUTIVE ELECTROL

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Designer Da-Tab Electrol User manual

Da-Lite

Da-Lite DESIGNER DA-TAB ELECTROL User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite TENSIONED DUAL MASKING ELECTROL User manual

Da-Lite

Da-Lite DESIGNER ELECTROL User manual

Da-Lite

Da-Lite Theater-lite User manual

Da-Lite

Da-Lite Fast-Fold NXT User manual

Da-Lite

Da-Lite CINEMA CONTOUR SCREEN User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite C with CSR User manual

Da-Lite

Da-Lite EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite Senior Electrol User manual

Da-Lite

Da-Lite Contour Electrol User manual

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite Tensioned Conference Electrol User manual

Da-Lite

Da-Lite TENSIONED PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Fast-Fold truss Frame User manual

Da-Lite

Da-Lite STUDIO ELECTROL User manual

Da-Lite

Da-Lite Perm Wall Frame User manual

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol User manual

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions