Da-Lite CINEMA CONTOUR SCREEN User manual

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

CINEMA CONTOUR®SCREEN

1. Unwrap the frame pieces. Assemble frame pieces on padding

material or other soft, clean surface. This will help keep the

frame clean and protect it from scratches.

2. Slide the frame pieces together at corners (Note: Frame

assembly holes may not appear to fit properly at the corners

until all fasteners have been attached. Once fasteners are

attached, the frame corners will be drawn in for a proper fit.)

Secure frame pieces with #10 screws provided. Do not

tighten screws until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”. Be sure

the frame pieces are assembled according to the labels. This will

ensure the snap pattern on the frame and screen surface will

match.

3. Attach the eight snap studs to the back of the frame in the

predrilled holes.

FRAME ASSEMBLY

FIGURE 1 (REAR VIEW)

SCREWS

SNAPS

LARGE WALL BRACKET (47" LONG)

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________

Screens over 96" viewing width = 3

Installation screws not included

SMALL WALL BRACKET (8" LONG)

Quantity = 1. Only for screens

80" and smaller viewing width. QUANTITY INCLUDED __________

Installation screws not included

SNAP STUD

QUANTITY INCLUDED ________

#10 SCREW

QUANTITY INCLUDED ________

HIGH POWER®FRAME BRACKET

Screens with High Power®quantity = 2

Screens with 2-piece side frame rails quantity = 2

QUANTITY INCLUDED ________________________________

USE INSTALLATION

METHOD NUMBER __________

2. To install the lower wall bracket, you must measure

the overall height of the screen frame and subtract

1-3/8". Using that dimension, measure down from the

top edge of the wall bracket and mark the wall for

two screw holes. The holes should be centered

within the frame and 6" apart. Refer to Figure 3.

3. Attach the small wall bracket to the wall. Refer to

Figure 4 for proper orientation. Do not tighten the

screws completely. The bracket should slide up and

down easily.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the inside of

the roll. Place the frame over the screen surface, and

while lifting the frame with one hand, snap the

screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

5. Hang the screen on the brackets by hooking the

bottom of the frame onto the lower wall bracket and

lift up until you can hook the top of the frame on the

top bracket. Push down on the frame to seat it on the

brackets. Refer to Figure 4.

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

There are four methods of installation based on the size

of the screen and type of viewing surface. Measure the

width of the viewing area of your screen and refer to the

appropriate method of installation below. The wall

bracket diagram shows the type and quantity of

bracket(s) supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power®viewing

surface.

INSTALLATION

FIGURE 2

SMALL WALL BRACKET

1-PIECE

FIGURE 3

FIGURE 4

LARGE WALL

BRACKET

1-PIECE

LARGE WALL BRACKET

OVERALL HEIGHT LESS 1-3/8"

OVERALL

HEIGHT

LIFT

WALL

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

1. Secure the wall bracket to wall studs at the desired

height. Make sure the bracket is level. The top of the

frame will be 1/8" above the top of the wall bracket

when mounted. You will need at least 5/8" clearance

above the bracket to hang the screen. Figures 2, 3, and

4 show the proper orientation for the supplied wall

brackets.

SMALL WALL

BRACKET

1. Secure the wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen. Figure 5 and 6 show the proper

orientation for the supplied wall brackets.

2. To install the bottom large wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

bottom wall bracket. See Figure 6.

3. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

4. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 6.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

1. Secure the wall brackets to wall studs at the

desired height. Make sure the brackets are level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen. Figure 6 and 7 show the proper

orientation for the supplied wall brackets.

2. To install the bottom large wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

lower wall bracket. See Figure 6.

3. Some large screen sizes (240") are made with 2-

piece side frame rails. For this type of frame you

will need to attach one High Power®bracket to

each side at the joint. Use the black #10 screws

supplied. See Figure 7.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

5. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 6.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

6. If you attached brackets to the side frame rails in

step 3, anchor these to the wall with an

appropriate fastener for your type of wall.

FIGURE 5

LARGE WALL

BRACKET

2-PIECES

FIGURE 6

OVERALL HEIGHT

LESS 1/4"

WALL

FIGURE 7

LARGE WALL

BRACKETS

3-PIECES

HIGH POWER®

BRACKET FOR

LARGE SPLIT

FRAMES

ONLY.

2-PIECES

METHOD 3 (SCREENS OVER 96" IN VIEWING

WIDTH)

METHOD 2 (SCREENS OVER 80" UP TO 96" IN

VIEWING WIDTH)

METHOD 4 (HIGH POWER®)

1. Secure the large wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen. See Figure 8.

2. Attach two High Power®brackets to the bottom

frame rail as shown in Figure 8. use the black #10

screws supplied.

3. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

4. Position the screen with the attached surface

onto the top wall bracket as shown in Figure 6.

Push down at the center of the bottom frame rail

to tension the fabric. Mark the screw holes for

the bottom brackets. Drill holes in wall and attach

the brackets to the wall with screws.

Da-Tex®, Dual Vision, Pearlescent, Cinema Vision, High

Power®, Da-Mat®, High Contrast Da-Mat®, Audio Vision,

High Contrast Audio Vision, High Contrast Cinema Vision

and High Contrast Cinema Perf surfaces can be

cleaned as follows:

Using a white clean cloth (100% cotton preferred)

that is dampened with clear water, gently wipe the

area in one direction. Do not use a circular motion.

Using a dry 100% cotton cloth, wipe dry after each

cleaning session. To clean a stubborn stain or a

sticky surface, use denatured alcohol (methanol or

methyl alcohol) following the same procedure as for

water.

FIGURE 8

LARGE WALL

BRACKET

1-PIECE

HIGH POWER®

BRACKET

2-PIECES

#10 SCREWS

4-PIECES

CLEANING

Printed in U.S.A. 87070 Rev. 1/08

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Large Cosmopolitan Electrol User manual

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL User manual

Da-Lite

Da-Lite TENSIONED HORIZON ELECTROL User manual

Da-Lite

Da-Lite Da-Glas User manual

Da-Lite

Da-Lite TENSIONED DIRECTOR ELECTROL User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite B User manual

Da-Lite

Da-Lite Fast-Fold NXT User manual

Da-Lite

Da-Lite Tensioned Director Electrol User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite senIor electrol User manual

Da-Lite

Da-Lite Boardroom ElEctrol User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Parallax User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite Deluxe Insta-Theater User manual

Da-Lite

Da-Lite Tensioned Contour Electrol 38798LC User manual

Da-Lite

Da-Lite SLIMLINE ELECTROL User manual

Da-Lite

Da-Lite VERSATOL User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite PRO IMAGER User manual

Da-Lite

Da-Lite IDEA Screen User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions