Da-Lite Contour Electrol User manual

INSTRUCTION BOOK FOR

Designer Contour®Electrol®

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of ire, electric shock, or

injury to persons.

Save These Instructions

Installation

Carefully unpack screen and remove outer wrapping from case.

Remove the black tape from the slat bar after the case has been installed.

There are three ways to install the Designer Contour Electrol: Wall Mount,

Ceiling Mount, or Ceiling Hook. Procedures for each method are as follows:

Wall Mount

1. Secure the wall mount bracket to the wall at the desired

height. Bracket should be fastened to wall studs or some

reinforcement within the wall. Concrete or brick walls require

special fasteners and anchors.

2. Make sure the bracket is level. See igure 1 for reference

dimensions.

3. Keep in mind you will need at least 5/8" between the ceiling

and the top of the wall mount bracket to be able to position

the case on the bracket.

4. Mount the screen case on the wall bracket as shown in igure 1.

Be sure the case is fully seated on the bracket. Tighten the

stop screws against the wall bracket.

Ceiling Mount

1. Do not remove the wall mount bracket, even if you are not

using it for mounting. This provides structural stability to

the case.

2. Be sure the ceiling has adequate reinforcement to attach the

screen brackets.

3. The top of the screen case has a channel that the ceiling

mount brackets slide into. Remove the end cap on the right

end of the case and insert the brackets into the case channel.

Lock the brackets in place by tightening two set screws. Refer

to igure 2. Mount cannot be more than 12" from end of case.

4. Hold the screen case up to the ceiling and mark the hole

locations. Drill holes into the ceiling and attach screen with

the appropriate fasteners for your ceiling.

Ceiling Hook

1. Do not remove the wall mount bracket, even if you are not

using it for mounting. This provides structural stability to

the case.

2. Be sure the ceiling has adequate reinforcement to attach

a hook anchor.

3. The top of the screen case has a channel that the ceiling

hook brackets slide into. Remove the end cap on the right

end of the case and insert the brackets into the case channel.

Lock the brackets in place by tightening two set screws.

Refer to igure 3.

4. The brackets can be attached anywhere within 12" of the end

of the case.

5. Attach an S-hook or similar fastener to the large center hole

on the bracket.

Figure 1

Figure 2

⁄" ⁄"

Case Hook

Set Screws (2)

Ceiling

Mount Holes

Endcap

Screws (3)

Wall Mount

Bracket

4 ¼"

4 ⅝"

Stop Screw

Figure 3

Set Screws (2)

Hook Mount

Hole

Endcap

Screws (3)

Electrical Installation

Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box located on the

left end of the screen case.

Standard installation is for a single 120VAC or 240VAC wall switch to control the screen. Optional Control units may have been ordered.

Wiring diagrams for the built-in VPI and low voltage control are included in these instructions. Refer to additional instructions for the

external VPI, external low voltage control, SCB100 and SCB200. Refer to the appropriate wiring diagram for your screen.

Of

Down

This Switch Can Not

be used with LVC.

SPDT Switch with

Center Of

Rear or DPDT Switch

with Center Of

120V Wiring Diagram

For Standard

Wall Switch

240V Wiring Diagram

For Standard

Wall Switch

AC (Common)

AC HOT 120VAC 60HZ 1 AMP

Black/Yellow

Black

Red

White

Black (Down)

Red (Up)

Junction Box

Located In Left Endcap

Junction Box

Located In Left Endcap

Ground-Must Be Connected

To Building Ground

White

Black

Red

Green

Motor

NOTE: A single switch cannot be used to operate more

than one screen. Contact the factory for further information.

This Switch Can Not

be used with LVC.

Brown and Yellow AC HOT

220/240 VAC 50HZ 2 AMP.

Blue AC (Common)

Brown

BLUE JUMPER

WIRE

Blue

Brown (Down)

Black (Up)

Blue

Brown

Black

Green

MOTOR

NOTE: A single switch cannot be used to operate more

than one screen. Contact the factory for further information.

Ground To Case

Ground-Must Be Connected

To Building Ground

Electrical Installation

EYE AUX

Low-Voltage

Wall Switch

Optional RF

or IR Remote

Connector

Motor

White (Common)

Black (Hot)

Green

Ground To Case

Red

Black

White (Common)

Black (Up)

Brown (Down)

Blue (Common)

120VAC 60HZ

120V Wiring Diagram

With Optional Built-In

Low Voltage Control

Black

White

Red

Black

White

Red

Stop

Down

Ground-Must

Be Connected

To Building

Ground

240V Wiring Diagram

With Optional Built-In

Low Voltage Control

Motor

Blue (Common)

Brown (Hot)

Green

Black

Ground To Case

AUX EYE

240VAC 50HZ

Optional RF or IR

Remote Connector

Low-Voltage

Wall Switch

Ground-Must

Be Connected

To Building

Ground

Black

Screen Adjustment

Screen travel is stopped automatically in the down and up

positions by the limit switches that are preset at the factory.

If it’s necessary to adjust for more or less drop follow the steps

below. The case cover must be removed to access the motor

limit switches.

Remove the case cover screw from both ends of the screen.

See igure 4. Be sure to hold the cover while removing the

screws.

Rotate the cover up and away from the case until it can

be removed.

SETTING THE DOWN LIMIT POSITION

To Reduce Screen Drop: Turn the red limit switch screw

clockwise to decrease the amount of screen drop. Run the

screen down to test the stop position. If the screen drops too far,

raise the screen about one foot and adjust the limit switch again.

Repeat until the desired position is set.

To Increase Screen Drop: Turn the red limit switch screw

counterclockwise to increase the amount of screen drop. Run the

screen down to test the stop position. If the screen does not

drop enough, raise the screen about one foot and adjust the limit

switch again. Repeat until the desired position is set.

CAUTION: Do not adjust for more drop than what was

ordered. At least 11/2 wraps of fabric must remain on the

roller. This screen comes standard with 0" or 2" black at

top. See the speciication data sheet for details.

ATTENTION! N'efectuez pas de réglage pour obtenir un

déroulement supérieur à celui commandé. Au moins 1 à 1/2

tour de toile doit être maintenu sur le cylindre. Cet écran est

doté de série d'une bande noire supérieure de 0 cm (0 po) ou

5 cm (2 po). Consultez la iche technique pour plus de

renseignements.

Hook

Figure 4

Figure 5

Rotate Up

Case Cover

Screw

Troubleshooting

Symptom Cause Solution

Screen will not operate.

Motor does not hum.

Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage, rewire

incoming electric line.

Blown fuse. Replace fuse.

Tripped circuit breaker. Reset circuit breaker.

No power to operating switch

or junction.

Check above. Tighten all loose wire connections. Correct any

improper connections.

Down Position

Check for power across black and white leads.

Up Position

Check for power across red and white leads.

Power at junction box

Thermal overload tripped. Let motor cool down for 15 minutes. Try again.

Broken wire in the “down” or “up” position. Check for continuity. Cut o old splice and reconnect.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Capacitor burned out. Replace motor assembly.

Incorrect stopping position in

downward direction.

Lost roller wrap. See instructions below.

“Down” limit switch out of adjustment. See installation instructions.

Incorrect stopping position in

upward direction.

Lost roller wrap. See instructions below.

“Up” limit switch out of adjustment. Adjust “up” limit switch. Call for information.

Noise.

NOTE: Screen will operate

with a low pitched hum.

Gear noise. Replace motor assembly.

Coasting. Defective brake. Replace motor assembly.

Restoring Lost Roller Wrap

1. Tape a strap to the bottom of the screen surface.

2. Push strap over back of roller.

3. Feed fabric as you pull strap to draw fabric over top of roller.

4. Remove tape and strap.

LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,

Warsaw, IN 465810137, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

89697

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0177 (Rev. 2) 09.14

Other manuals for Contour Electrol

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Wireline Advantage User manual

Da-Lite

Da-Lite Senior Electrol User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite Parallax User manual

Da-Lite

Da-Lite Cinema Contour Screen User manual

Da-Lite

Da-Lite senIor electrol User manual

Da-Lite

Da-Lite Designer Contour Manual User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite TENSIONED HORIZON ELECTROL User manual

Da-Lite

Da-Lite DESIGNER CONTOUR ELECTROL Series User manual

Da-Lite

Da-Lite Da-Glas User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite UTB Contour User manual

Da-Lite

Da-Lite IDEA Screen User manual

Da-Lite

Da-Lite Horizon Electrol User manual

Da-Lite

Da-Lite DELUXE MODEL B User manual

Da-Lite

Da-Lite C with CSR User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite TENSIONED COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Whiteboard Mount User manual

Da-Lite

Da-Lite Large Cosmopolitan Electrol User manual

Da-Lite

Da-Lite MULTI-MASK IMAGER User manual

Da-Lite

Da-Lite ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite Parallax Thin User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions