Da-Lite ADVANTAGE ELECTROL User manual

INSTRUCTION BOOK FOR

Advantage®Electrol®

Original Instructions

Important Safety Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.

However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide

for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any

kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone

assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Maximum surrounding air temperature 122°F (50°C).

3. Main disconnect must be incorporated in the ixed wiring in

accordance with the wiring rules.

4. Rated for indoor use only.

5. Use copper rated conductors rated 167°F (75°C) or higher.

6. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualiied persons in

order to avoid hazard.

7. Supplied drive is only intended for use in Da-Lite screen models

Advantage, Contour, and Cosmopolitan.

8. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

9. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

10. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

11. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

12. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

13. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not recommended

by the manufacturer.

Save These Instructions

Advantage®Electrol®Suggested Methods of Installation

⅜" Threaded Rod

(Not Supplied)

Hanger Bracket

Electrical

Junction Box

Motor

End

Variable Position

Mounting Bracket

Audience Side

6 ⁄"

6 ⁄"

7 ¾"

⅜" Threaded Rod

(Not Included)

Attached To

Mounting Bracket

Self-Trimming

Flange Finished

Ceiling

7 ¾"

6 ⁄"

6 ⅜"

3 ⁄"

7 ⁄"

6 ⁄"

Method 1

Method 2

9 ¼"

Tools Required for Installation

1. Hang case and attach to support structure with bolts.

See Suggested Methods of Installation.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, case must be levelled side to

side and front to back.

3. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box

cover and secure with 2 screws.

NOTE: Must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code

(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70.

Case Installation

Pre-Installation

1. Carefully unpack case from shipping carton.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam covering the outside of

the case.

#2 Phillips Screwdriver 1/2“ Open Wrench

or Socket Driver

5. For shipping purposes, foam is also inserted between the

roller brackets and end caps (Figure 1). Remove these foam

blocks from the ends.

6. Remove the hanger brackets from the top of the case using a

1/2” wrench. Do not discard the hardware; it will be used

during case installation to re-attach the hanger brackets for

mounting.

If your case was ordered in advance of the screen and

roller assembly, your installation is now complete.

Continue to step 4 if your Advantage Electrol was ordered

as a complete unit.

4. Carefully remove paper and tape from roller assembly.

DO NOT use a knife or sharp object to cut tape; you will

damage the screen. Pull orange string..

5. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 1 minute on and 3 minutes of.

Screen and Roller Assembly Installation

Motor Mount

Bracket

Motor Power

Connector

1/420 Nuts

Access Door Screws

Foam Blocks

Pin End

Figure 1

Motor End

Follow these steps if your screen and roller assembly was ordered separately from the case.

1. Remove the access door. First, remove the 2 screws from the

ends. Be sure to support the door during this step to avoid

injury. Then lift the door slightly and pull away from the edge

of the case (Figure 1).

2. Carefully unpack screen and roller assembly. Leave packing

paper on roller.

3. To install screen and roller assembly, loosen (but do not

remove) four 1/420 nuts securing pin end bracket (opposite

end from the junction box) to the case housing. Slide the pin

end bracket towards the end of the case (Figure 2).

4. Insert the motor end square shaft into the motor end bracket

(junction box end) and secure with the cotter pin. (Figure 2).

5. Moving to the pin end of the case, slide the pin end bracket

until the hole its securely over the pin and secure with the

cotter pin. Tighten the 1/420 nuts on the pin end bracket

securely (Figure 2).

6. Complete electrical hook-up by snapping motor wire

connector into case connector (Figure 2).

7. Carefully remove paper and tape from roller assembly.

DO NOT use a knife or sharp object to cut tape; you will

damage the screen. Pull orange string.

8. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 1 minute on and 3 minutes of.

9. Re-install the access door. Procedure is the reverse of step 1

listed above.

Cotter Pins

Motor

Figure 2

4. Insert motor in tube with seam of tube lined up with drive wheel and collar cutouts.

Seam of Tube

Motor Collar

Motor Drive Wheel

Motor Key

Replacement Motor Instruction

Rated torque of model DL45E10/26 is 10 N/m with a duty cycle of 1 min. on / 3 min. of.

Rated torque of model DL45EQ6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. of.

Motor is intended for use in Da-Lite screens incorporating a 3.00" and 3.25" roller diameter.

1. Make sure motor collar is on motor.

2. Collars keyway must line up with the key on the motor.

3. Secure motor drive wheel on output shaft of motor and insert retaining clip.

Screen And Roller Assembly Installation (continued)

RJ45

Receptacle

RJ22

Output

(QAUX)

RJ22

Inputs

(QEYE)

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

Advantage®Electrol®Installation For 120V Screens

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Green

Red

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

120V Wiring Diagram

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the

BUS terminals on the wall switch to the corresponding BUS

terminals on the splitter board.

STOP

DOWN

BUS

COM

Power Input 120VAC / 60Hz

Green (Ground)

(Ground–Must be Connected

to Building Ground)

Black

(Hot)

White

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Installation Video

To view a video of this installation,

visit http://youtu.be/t2ZQ9PVAhEg

or use the QR code below.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

Advantage®Electrol®Installation for 220V Screens

RJ45

Receptacle

RJ22

Output

RJ22

Inputs

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Red

Green

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

220V Wiring Diagram with Operation & Limit Adjustment

Wall Switch

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the BUS

terminals on the wall switch to the corresponding BUS terminals

on the splitter board.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

STOP

DOWN

BUS

COM

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Advantage®Electrol®Installation for 220V Screens (continued)

220V Wiring Diagram with European Style Wall Switch

Use 3-conductor 2024 gauge wire for wall switch connections.

IMPORTANT NOTE: The European style wall switch is for

operation only and CANNOT be used to make limit switch

adjustments. Therefore, it is advised to wire the limit adjustment

switch or provide a 3-conductor connection that is accessible.

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

Black (Down)

White (Common)

Red (Up)

Red

Black

White

Inputs

Output

Black (Down)

White (L / Common)

Red (Up)

Push Down on Tab to

Insert Wire

STOP

DOWN

BUS

COM

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack (QEYE)

Optional Built-In Video Projector Interface

5/12 Volt

Screen Trigger

on Projector

Black

Red

VPI Trigger

Module

CAUTION: The projector must be turned of before

connecting the trigger wires to the projector. Failure to

do so may damage the controller.

ATTENTION: Le projecteur doit être éteint avant de

brancher les ils de déclenchement à celui-ci. Tout

manquement à cette instruction pourrait endommager le

contrôleur.

Use 2-conductor 1824 gauge wire to extend the low voltage

connection from the projector’s 5 or 12-volt screen trigger output

to the length required to reach the VPI.

NOTE: When extending the low voltage connection from the

projector’s screen trigger output polarity does not matter. The

red and black wires from the VPI are interchangeable.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the BUS

terminals on the wall switch to the corresponding BUS terminals

on the splitter board.

See 120V or 220V wiring diagram for complete wiring

instructions.

Other manuals for ADVANTAGE ELECTROL

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite Contour Electrol User manual

Da-Lite

Da-Lite DELUXE MODEL B User manual

Da-Lite

Da-Lite FullVision User manual

Da-Lite

Da-Lite Contour Electrol User manual

Da-Lite

Da-Lite Polacoat Da-Plex Semi-Rigid User manual

Da-Lite

Da-Lite advantage User manual

Da-Lite

Da-Lite Tensioned Cosmopolitan electrol User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Horizon Electrol User manual

Da-Lite

Da-Lite ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite Slimline Electrol User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Da-Lite

Da-Lite Parallax User manual

Da-Lite

Da-Lite DIRECTOR ELECTROL User manual

Da-Lite

Da-Lite TENSIONED COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED LARGE ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED DIRECTOR ELECTROL User manual

Da-Lite

Da-Lite UTB Contour User manual

Da-Lite

Da-Lite PERM WALL FRAME User manual

Da-Lite

Da-Lite PRO IMAGER User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions