Cognex DataMan 260 Series User manual

DataMan®260 Series

Quick Reference Guide

2021 May 26

Revision: 6.1.10-SR1.4

Precautions

To reduce the risk of injury or equipment damage, observe the following precautions

when you install the Cognex product:

lThis device requires the use of an LPS or NEC class 2 power supply (non-

PoE device) or the use of a PoE Class 1 (PoE device).

lDo not connect or disconnect this device from the I/O module or 15-pin USB

adapter cable when the I/O module or adapter cable is connected to a PC.

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThisdevice should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

lThis product is intended for industrial use in automated manufacturing or

similar applications.

lThe safety of any system incorporating this product is the responsibility of

the assembler of the system.

lThisproduct does not contain user-serviceable parts. Do not make

electrical or mechanical modifications to product components.

Unauthorized modifications can void your warranty.

Symbols

The following symbols indicate safety precautions and supplemental information:

WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical

shock.

CAUTION:This symbol indicates a hazard that could result in property damage.

Note: This symbol indicates additional information about a subject.

Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.

Product Overview

Item Description

1 Illumination LEDs

2 LED aimers

3-4* Mounting holes (M3 x 3.5mm)

5 Trigger button

6 Power indicator

7 Train status indicator

8 Good/bad read indicator

9 Network status indicator

10 Error indicator

11 Tune button

12 Power, I/O and RS-232 connector

13 Ethernet connector

Note: *Use only one set of mounting holes (either 3 OR 4) for mounting.

Note: The five status LEDs together also function as a peak meter using an orange light.

DataMan 260 Accessories

LENS OPTIONS, COVERS, ILLUMINATIONS AND FILTERS

Accessory Name Accessory Number Accessory Image

6.2 mm lens kit DM150-LENS-62

IR 6.2 mm lens kit, 3 -position with IR LED DMA-KIT-IR-62

IR16 mm lens kit DMA-KIT-IR-16

16 mm lens with extended optics mount (requires the

use of an extended front cover and high-powered red

LED)

DM260-LENS-16

UV Light Kit for 6.2 mm lens (365nm) DMA-KIT-UV365-62

Liquid Lens Module (LLM) to be used with 6.2 mm lens

or 16 mm lens

DMA-LLM-150-260

ImageMax kit DM260-KIT-16LL

Clear lens cover* DM150-CVR-CLR

Clear lens cover,ESD safe* DM150-CVR-ESD

Polarized front cover* DM260-LENS-62CVR-

F***

Extended lens cover, un-polarized**

Extended lens cover, half-polarized **

Extended lens cover, fully polarized**

DM260-LENS-16CVR***

DM260-LENS-16CVR-

P***

DM260-LENS-16CVR-

F***

C-mount adaptor, IP40 DM260-CMNT-00

C-mount adaptor, IP65 DM260-CMNT-CVR

Blue bandpass filter DM150-BP470

Red bandpass filter DM150-BP635

Red LED illumination*

White LED illumination*

Blue LED illumination*

DM150-LED-RED

DM150-LED-WHT

DM150-LED-BLU

High Powered red LED illumination** DM260-LED-RED-HP

Note: *Use with a 6.2 mm lens only!

**Use with a 16 mm lens only!

***ESD safe

CABLES ANDOTHER

Accessory Name Accessory Number Accessory Image

Connection cable 24V, I/O, RS-232 CCBL-05-01

CCB-M12x12Fy-xx (y=S:

straight / y=A: angled *, xx

specifies length)

Connection cable RS-232 CCB-M12xDB9Y-05

Adapter cable, M12x12 to M8x4/M8x5, 0.5 m DM260-ADAP-M12M8

X-Coded to RJ45 Ethernet Cable CCB-84901-2001-xx,

where xx can be 02, 05, 10,

15 or 30, indicating length

in meters

Adapter cable, ETH, M12, X-CODED/A-CODED, 0.5 m CCB-M12x8MS-XCAC

Universal Mounting Bracket DM100-UBRK-000

Pivot Mounting Bracket DM100-PIVOTM-00

Dimensional Drawings

The size of the DataMan 260 in the angled configuration is shown in the following

figures:

Other manuals for DataMan 260 Series

This manual suits for next models

Table of contents

Cognex DataMan 260 Series User manual

Popular Barcode Reader manuals by other brands