Cognex DataMan 8072 DL User manual

DataMan®8072 DL

Quick Reference Guide

2019 October 08

Revision: 6.1.6SR1.5

Precautions

To reduce the risk of injury or equipment damage, observe the following precautions

when you install the Cognex product:

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Product Overview

1 Illumination module

2 LEDaimers

3 Illumination LEDs

4 Trigger (press and hold to read)

5 Lanyard hook

6 Indicator light

7 Communication module insertion point

Base Station Overview

1 Base station status indicators

2 PAIR sticker - Reading the code pairs the base station

with the device

3Connection point to the reader:

lpairing reader and base station

lnon-wireless communication

lcharging

4 RS-232

5 USB

6 Power plug (24V, max. 15W)

7 Alternative power supply connector (24V, max. 15W,

polarity marked on the plastic part near the connector).

Recommended wire diameter is 14- 18 AWG

8 Ethernet

DataMan 8072 DL Accessories

Serial/USB slide-in DMCM-SERIALM-00

Ethernet slide-in DMCM-ENETM-00

Bluetooth slide-in DMCM-BTM-00

Charging base station DMA-CBASE-01

Intelligent Bluetooth base station DMA-IBASE-BT-02

Power Supply for base station DMA-24VPWR-xx*

Power Supply for reader DM100-PWR-000

Battery for the wireless reader DMA-HHBATTERY-01

Multi-battery charger DMA-MBC-xx*

POE adapter CPS-24V-POE1

POE adapter CPS-24V-POE4

POE adapter CPS-AC-POE1A-xx*

Wall mount DMA-WALL-8000-00

Wall mount for base station DMA-IBASE-WALL-00

Stand DM-STAND-00

*xx can be US, EN, UK, or JP.

Cables

Coiled RS-232 cable for reader, 2.5 m DM8000-RS232-02

Industrial RS-232 cable for reader, 2.5 m DM8000-RS232IND-02

Coiled RS-232 cable for reader, 4 m DM8000-RS232-05

Coiled USB cable, 2.5 m DM8500-USBC-02

Ethernet cable, 2.5 m DM8000-ECABLE-02

Ethernet cable, 30 m DM8000-ECABLE-30

Ethernet cable, 5 m DM8000-ECABLE-05

USB cable, 2.5 m DM8500-USB-00

Coiled Ethernet cable, 5m DM8000-ECABLEC-05**

RJ25 (RJ12) to DSUB9 cable for base station, 5 m DMA-RS232RJ-05

** Collimated cable length including DM8000-ECABLE-X should not exceed 50 m.

lUSB cable for base station: Use any standard USB-A to USB-B 2.0 cable up to 3 meters.

lEthernet cable for base station: Use any standard CAT5/5e, SF/FTP or S/FTP cable.

lDMA-USB-00: Straight 10ft USB cable.

Field of View and Reading Distances

DataMan 8072 DL with a 6.2 mm Lens (Standard Range, Focused to 75 mm)

Device Distances in mm/1D min. code Distances in mm/2D min. code

DM8072 20-170 6 MIL 0-200 10 MIL

0-200 10 MIL 0-260 15 MIL

0-260 15 MIL 0-300 20 MIL

Connecting the Reader

Bluetooth Readers

1. Connect the slide-in to the reader and tighten the screws to lock the slide-in.

2. Insert the battery.

3. Insert the plug.

Corded Readers

1. Connect the slide-in to the reader and tighten the screws to lock the slide-in.

2. Insert the plug. Slide the cable lock up to the reader and twist the cable lock

in place.

Note: Disconnect the DataMan 8072 from power or remove the battery before inserting/removing the

communication modules.

Installation

Installation procedures and specifications are presented in detail in the DataMan

8072 DL Reference Manual, which is installed with the DataMan Setup Tool. From

the Windows Start menu, select the following to access the manual: All Programs >

Cognex > DataMan Software vx.x.x > Documentation.

Note:

lCables are sold separately.

lIf a standard component is missing or damaged, immediately contact

your Cognex Authorized Service Provider (ASP) or Cognex

Technical Support.

CAUTION:All cable connectors are "keyed" to fit the connectors on the

DataMan system; do not force the connectors or damage may occur.

Install Software and Documentation and

Connect the Reader

To configure a DataMan 8072 DL reader, the DataMan Setup Tool software must

be installed on a networked PC. The DataMan Setup Tool is available from the

DataMan support site: http://www.cognex.com/support/dataman.

1. After installing the software, connect the DataMan 8072 DL to your PC.

2. Launch the DataMan Setup Tool and click Refresh.

3. Select your DataMan 8072 DL reader from the list and click Connect.

DataMan 8072 Specifications

Weight 254 g (without slide-in)

Operating Temperature 0ºC — 40ºC (32ºF — 104ºF)

Storage Temperature -10ºC — 60ºC (14ºF — 140ºF)

Maximum Humidity < 95% (non-condensing)

Environemntal IP65

Codes 1-D barcodes: Codabar, Code 39, Code 128, and Code 93, Interleaved 2 of 5,

Pharma, GS1 DataBar, Postal, UPC/EAN/JAN, DataBar

2-D barcodes: Data MatrixT M ; QR Code and microQR Code, RSS/CS, PDF 417,

MicroPDF 417, MaxiCode, Aztec Code

Power Supply Requirements USB: external 5.0 W maximum LPS or NEC class 2 power supply: +5V - +6V DC

RS232 external 5.0W max LPS or NEC class 2 power supply

+6.0V 1A DC (5.0m RS-232 cable)

+6.0V 1A DC (2.5m RS-232 cable)

ETH: Class 2 PoE supply IEEE 802.3af (connect only to PoE networks without

routing to the outside plant)

Inrush current peak 5A maximum

Duration: approx. 30μs

Electrical charge: 60μAs at 6V

Battery life for wireless

reader (typical use case)

ca. 4100 triggers can be operated within a 13 hour working shift

Ethernet 10/100 Base-T FULL/HALF DUPLEX, IEEE 802.3

Bluetooth Bluetooth™ 2.1, 2.4 GHz

DataMan 8072 Imager Specifications

Specification DataMan 8072 Imager

Image Sensor 1/3 inch CMOS

Image Sensor Properties 3.75 μm square pixels

Image Resolution (Pixels) 1280 x 960

Lens Type 6.2 mm F:10 lens

Other manuals for DataMan 8072 DL

Table of contents

Cognex DataMan 8072 DL User manual

Popular Barcode Reader manuals by other brands