Cognex DataMan 8072 Verifier User manual

DataMan®8072 Verifier

Quick Reference Guide

2019 October 08

Revision: 6.1.6SR1.5

Precautions

WARNING: LASER LIGHT, DO NOT STARE INTO BEAM: CLASS 2

LASER PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS

MAY CAUSE SERIOUS INJURY.

To reduce the risk of injury or equipment damage, observe the following precautions

when you install the Cognex product:

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Product Overview

WARNING:LASER LIGHT, DO NOT STARE INTO BEAM

1 Imager and Lens Optical System

2 Illumination

3 Removable Standoff

4 Trigger (press and release)

5 Lanyard hook

6 Indicator light

7 Communication module insertion point

Status indicators:

lCommunication:

oGREEN = good verification

oRED = bad verification

DataMan 8072 Verifier Kits

The DataMan 8072 Verifier is available in the following kits:

Model number Description

DMV-8072V-S-0200 DataMan 8072 Verifier Ethernet Kit with Stand:

- 8072 Verifier

- Standoff

- Ethernet Slide-In

- Ethernet Cable Attachment

- Standard Ethernet Cable

- POE Injector

- Basic Calibration Card

- Stand Accessory

DMV-8072V-S-0100 DataMan 8072 Verifier USB Kit with Stand:

- 8072 Verifier

- Standoff

- USB Slide-In

- USB Cable

- Power Supply

- Basic Calibration Card

- Stand Accessory

DMV-8072V-0200 DataMan 8072 Verifier Ethernet Kit:

- 8072 Verifier

- Standoff

- Ethernet Slide-In

- Ethernet Cable Attachment

- POE Injector

- Basic Calibration

DMV-8072V-0100 DataMan 8072 Verifier USB Kit

- 8072 Verifier

- Standoff

- USB Slide-In

- USB Cable

- Power Supply

- Basic Calibration Card

DMV-8072V-0000 DataMan 8072 Verifier Kit No Slide-In

- 8072 Verifier

- Standoff

- Basic Calibration Card

DataMan 8072 verifier and stand-off Ethernet or USB slide-in

Stand accessory Calibration card

DataMan 8072V Verifier Accessories

Ethernet Slide-In DMCM-ENETM-00

Serial/USB 2.0 Slide-In DMCM-USB2EN-00

Power Supply for USB 2.0 Slide-In DM100-PWR-000

POE hub CPS-AC-POE1A-US

Stand Accessory DMV-8072V-STAND

Cognex Basic Calibration Card DMV-CCC

DMV-WCC

GS1 Conformance Calibration Card DMV-GS1CC

Validation Protocol DM8072V DMV-VPS-DPM

Cables

USB Cable for USB 2.0 Slide-In, 2.5 m DM8500-USBC-02

Ethernet Cable for Ethernet Slide-In, 5 m DM8000-ECABLE-05

Standard Ethernet Cable CBL-C10E

Connecting the Verifier

1. Connect the slide-in to the reader, and tighten the screws to lock the slide-

in.

2. Insert the plug. Slide the cable lock up to the verifier, and twist the cable lock

in place.

Note: Disconnect the DataMan 8072V Verifier from power or remove the battery before inserting/removing

the communication modules.

Installation

Installation procedures and specifications are presented in detail in the DataMan

8072 Verifier Reference Manual, which is installed with the DataMan Setup Tool.

From the Windows Start menu, select the following to access the manual: All

Programs > Cognex > DataMan Software vx.x.x > Documentation.

Note:

lCables are sold separately.

lIf a standard component is missing or damaged, immediately contact

your Cognex Authorized Service Provider (ASP) or Cognex

Technical Support.

CAUTION:All cable connectors are "keyed" to fit the connectors on the

DataMan system; do not force the connectors or damage may occur.

Install Software and Documentation and

Connect the Reader

To configure a DataMan 8072V Verifier, the DataMan Setup Tool software must be

installed on a networked PC. The DataMan Setup Tool is available from the

DataMan support site: http://www.cognex.com/support/dataman.

1. After installing the software, connect the DataMan 8072V Verifier to your

PC.

2. Launch the DataMan Setup Tool and click Refresh.

3. Select your DataMan 8072V Verifier from the list and click Connect.

DataMan 8072V Verifier Specifications

Weight 400 g (including grip assembly with battery)

Operating Temperature 0ºC — 45ºC (32ºF — 113ºF)

Storage Temperature 0ºC — 60ºC (32ºF — 140ºF)

Maximum Humidity 95% (non-condensing)

Environemntal IP65

Codes 2-D barcodes: Data MatrixTM (IDMax and IDQuick: ECC200), QR Code

Power Supply

Requirements

USB: bus powered (optionally: external 6W max LPS or NEC class 2 power supply +5V

- +6V DC)

ETH: Class 2 PoE supply IEEE 802.3af (connect only to PoE networks without routing to

the outside plant)

Inrush current peak 5A maximum

Duration: approx. 30μs

Ethernet 10/100 Base-T FULL/HALF DUPLEX, IEEE 802.3

DataMan 8072V Verifier Imager Specifications

Specification DataMan 8072V Verifier Imager

Image Sensor 1/3 inch CMOS global shutter

Image Sensor Properties 3.75 μm square pixels

Image Resolution (Pixels) 1280 x 966

Lens Type 12 mm F:4 S-mount lens

LED Wavelengths

The following table shows LED types and the related wavelengths:

LED λ [nm]

RED 660

Table of contents

Cognex DataMan 8072 Verifier User manual

Popular Barcode Reader manuals by other brands