Cognex DM503 User manual

DataMan®503

Quick Reference Guide

04/13/2017

Version:5.7.0.42

Precautions

Observe these precautions when installing the Cognex product, to reduce the risk of

injury or equipment damage:

lTo reduce the risk of damage or malfunction due to over-voltage, line noise,

electrostatic discharge (ESD), power surges, or other irregularities in the

power supply, route all cables and wires away from high-voltage power

sources.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lCable shielding can be degraded or cables can be damaged or wear out

more quickly if a service loop or bend radius is tighter than 10X the cable

diameter. The bend radius must begin at least six inches from the

connector.

lThis device should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purpose only and may be changed

without notice.

Product Overview

1 External illumination mounting point

2 Mounting holes (M3 x 5mm)

3 Trigger button

4 Power

5 Train status

6 Good/bad read

7 Network

8 Error

9 Tuning button

10 Peak meter

11 Synchronized Acquisition

12 RS-232

13 External light control

14 Ethernet

15 Power I/O

DataMan 503 Accessories

16 mm, 25 mm and 35 mm lens (LEC-CFFxx-F8)

(xx specifies focal length)

Connection cable 24V, I/O (CCBL-05-01)

Ethernet M12 to RJ45 cable (CCB-84901-y00x-xx) (y straight/angled, x-xx

specifies length)

External light cable (CCB-M12x4MS-xxx) (xxx specifies length)

I/O extension cable, 5m straight (CKR-200-CBL-EXT)

RS-232 M8 to SUB-D cable (CCB-M8X4-xx)

Synchronization Cable (DM503-SYNC-012 - 1.2 meter, DM503-SYNC-05 - 5

meter)

Xpand 15 (DMA-FOVE-15)

Xpand 25 (DMA-FOVE-25)

SVL Light Bar (IVSL-YLW300-xxx)

DM503 high power illumination (DM503-HPIA-xxx)

Dimensions

Field of View and Reading Distances

Connecting the Reader

Installation

Installation procedures and specifications are presented in detail in the DataMan®

503 Reference Manual, which is installed with the DataMan Setup Tool. From the

Windows Start menu, select the following to access the manual: All Programs >

Cognex > DataMan Software vx.x.x > Documentation.

Note:

lCables are sold separately.

lIf any of the standard components appear to be missing or damaged,

immediately contact your Cognex Authorized Service Provider (ASP)

or Cognex Technical Support.

CAUTION:All cable connectors are "keyed" to fit the connectors on the

DataMan system; do not force the connectors or damage may occur.

Install Software and Documentation and

Connect the Reader

Follow the steps below to connect your reader to power and network:

1. Connect the I/O+RS232+24V cable to your reader.

2. For a network connection, connect your reader through an Ethernet cable

to your network.

3. Connect the cable to a 24V power supply.

To configure a DataMan 503 reader, the DataMan Setup Tool software must be

installed on a networked PC. The DataMan Setup Tool is available from the

DataMan support site: http://www.cognex.com/support/dataman.

1. After installing the software, connect the DataMan 503reader to your PC.

2. Launch the DataMan Setup Tool and click Refresh.

3. Select your DataMan 503 reader from the list and click Connect.

This manual suits for next models

Table of contents

Other Cognex Barcode Reader manuals

Cognex

Cognex DM8072 ER User manual

Cognex

Cognex DataMan 503 User manual

Cognex

Cognex DataMan DM474 User manual

Cognex

Cognex DataMan 370 Series User manual

Cognex

Cognex DataMan 8072 DL User manual

Cognex

Cognex DataMan 8600 Series User manual

Cognex

Cognex VisionPro Trevista CI Dome User manual

Cognex

Cognex DATAMAN 500 User manual

Cognex

Cognex DataMan 8050 User manual

Cognex

Cognex DataMan 280 Series User manual

Cognex

Cognex In-Sight 2800 Series User manual

Cognex

Cognex DataMan 8700 User manual

Cognex

Cognex DM260Q User manual

Cognex

Cognex DataMan 8050 User manual

Cognex

Cognex DataMan 300 Series User manual

Cognex

Cognex DataMan 370 Series Operating instructions

Cognex

Cognex DataMan 8700 User manual

Cognex

Cognex DataMan Operating instructions

Cognex

Cognex DataMan 8000 Series User manual

Cognex

Cognex DataMan 475 User manual

Cognex

Cognex DataMan 7550 User manual

Cognex

Cognex DataMan 50 User manual

Cognex

Cognex DataMan 302L User manual

Cognex

Cognex DataMan 300 Series User manual

Cognex DM503 User manual

Popular Barcode Reader manuals by other brands