Cognex DataMan 280 Series User manual

DataMan®280 Series

Quick Reference Guide

2023 February 01

Revision: 23.1.0.5

Precautions

To reduce the risk of injury or equipment damage, observe the following precautions

when you install the Cognex product:

lConnectivity is possible through the following options:

l24 VDC (+/- 10%) output connection using a UL or NTRL listed

power supply

lPower over Ethernet (PoE) 13 W power supply

Any other voltage creates a risk of fire or shock and can damage the

components. Applicable national and local wiring standards and rules must

be followed.

lThis product is intended for industrial use in automated manufacturing or

similar applications.

lThe safety of any system incorporating this product is the responsibility of

the assembler of the system.

lDo not install Cognex products where they are exposed to environmental

hazards such as excessive heat, dust, moisture, humidity, impact, vibration,

corrosive substances, flammable substances, or static electricity.

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lDo not expose the image sensor to laser light. Image sensors can be

damaged by direct, or reflected, laser light. If your application requires laser

light that might strike the image sensor, use a lens filter at the corresponding

laser wavelength. For suggestions, contact your local integrator or

application engineer.

lThisproduct does not contain user-serviceable parts. Do not make

electrical or mechanical modifications to product components.

Unauthorized modifications can void your warranty.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lInclude service loops with cable connections.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThisdevice should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Symbols

The following symbols indicate safety precautions and supplemental information:

WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical

shock.

CAUTION:This symbol indicates a hazard that could result in property damage.

Note: This symbol indicates additional information about a subject.

Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.

Accessories

You can purchase the following components separately. For a list of options and

accessories, contact your local Cognex sales representative.

DataMan 280 Series Lenses

Accessory Product Number Illustration DM280 DM282

6.2 mm lens kit that includes:

l6.2 mm optics mount

l6.2 mm lens

lManual lens cap (assembled)

lScrews

DM280-LENS-62 ✓

16 mm lens kit with extended optics mount (requires

the use of an extended front cover and high-powered

red LED). The kit includes:

l16 mm optics mount

l16 mm lens

lManual lens cap (assembled)

lScrews

DM260-LENS-16 ✓

IR16 mm lens kit that includes:

l16 mm optics mount

l16 mm lens (IR)

lStandard Infrared Light for 16mm (Risk

Group Exempt acc. IEC62471)

lManual lens cap (assembled)

lScrews

DMA-KIT-IR-16 ✓

Accessory Product Number Illustration DM280 DM282

IR16 mm lens kit that includes:

l16 mm optics mount

l16 mm lens (IR)

lHigh Speed Liquid Lens Module (DMA-

HSLL-280)

lStandard Infrared Light for 16mm (Risk

Group Exempt acc. IEC62471)

lManual lens cap (assembled)

lScrews

280-KIT-2MP-IR16 ✓

High Speed Liquid Lens Module (HSLL) to be used

with 6.2 mm lens or 16 mm lens

DMA-HSLL-280 ✓ ✓

16 mm lens with ImageMax kit that includes:

l16 mm optics mount

l16 mm lens

lHigh Speed Liquid Lens Module (DMA-

HSLL-280)

lHigh Powered red LED illumination

(DM260-LED-RED-HP) (Risk Group

Exempt acc. IEC62471)

l2-LED half-polarized extended cover

(DM260-LENS-16CVR-P) (Risk Group

Exempt acc. IEC62471)

DM280-KIT-IMGMAX ✓

Accessory Product Number Illustration DM280 DM282

Blue bandpass filter DM150-BP470 ✓

Blue bandpass filter, 450nm 280-TORCH-BP450 ✓

Red bandpass filter DM150-BP635 ✓

Red bandpass filter, 635nm 280-TORCH-BP635 ✓

DataMan 280 Series Lens Covers

Accessory Product Number Illustration DM280 DM282

Standard front cover. Use with a 6.2 mm lens only. DM280-CVR-62 ✓

Standard front cover, half-polarized. Use with a 6.2 mm

lens only.

DM280-LENS-

62CVR-P

✓

Standard front cover, fully-polarized. Use with a 6.2

mm lens only.

DM260-LENS-

62CVR-F

✓

Extended front cover. Use with a 16 mm lens only. DM260-LENS-

16CVR

✓

Extended front cover, half-polarized. Use with a 16 mm

lens only. DM260-LENS-

16CVR-P

✓

Extended front cover, fully-polarized. Use with a 16 mm

lens only. DM260-LENS-

16CVR-F

✓

C-mount adapter, IP40 DM280-CMNT-00 ✓

Accessory Product Number Illustration DM280 DM282

Cross-polarized cover for High-Power Integrated Torch 280-HPIT-COVPOL ✓

Clear cover for High-Power Integrated Torch 280-HPIT-COVCLR ✓

Diffuse cover for High-Power Integrated Torch 280-HPIT-COVDIF ✓

Dome Diffuser cover for High-Power Integrated Torch 280-HPIT-DOME ✓

CAUTION:For 280-HPIT-COVPOL, 280-HPIT-COVCLR, and 280-HPIT-

COVDIF equipped with a laser aimer, the device has been tested to be under

the limits of a Class1 Laser device.

DataMan 280 Series Cables

Note: Cables are sold separately.

Accessory Product Number Illustration DM280 DM282

Ethernet Cable, X-coded M12-8

to RJ-45

CCB-84901-2001-xx (straight, xx specifies

length: 2m, 5m, 10m, 15m, 30m)

✓ ✓

Ethernet Cable, X-coded M12-8

to RJ-45

CCB-84901-2002-xx (right-angled, xx

specifies length: 2m, 5m, 10m)

✓ ✓

Ethernet Cable, Robotic X-

Coded M12-8 to RJ-45

CCB-84901-2RBT-xx (straight, xx specifies

length: 2m, 5m, 10m)

✓ ✓

X-Coded to A-Coded Ethernet

cable adapter, 0.5 m

CCB-M12X8MS-XCAC ✓ ✓

Power and I/O Breakout Cable,

M12-12 to Flying Lead

CCB-M12x12Fy-05 (y = straight/angled, xx

specifies length)

✓ ✓

Power and I/O Breakout Cable,

M12-12 to Flying Lead

CCBL-05-01 ✓ ✓

Power and I/O Breakout Cable,

M12-12 to Flying Lead

CCB-PWRIO- xx (straight, xx specifies

length: 5m, 10m, 15m)

✓ ✓

Other manuals for DataMan 280 Series

This manual suits for next models

Table of contents

Cognex DataMan 280 Series User manual

Popular Barcode Reader manuals by other brands