Clarke CRWP1 User manual

OPERATING INSTRUCTIONS

GC0311

SEMI-ROTARY HAND PUMP

Model No: CRWP1

PART NO: 7130030

INTRODUCTION

Thank you for purchasing this CLARKE Semi-rotary Hand Pump. This product

has been designed to give long and trouble free service. If however, having

followed the instructions in this booklet carefully, you encounter problems,

take the unit to your local CLARKE dealer.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase. This guarantee is invalid if the product is found

to have been abused, tampered with, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

SPECIFICATION

Dimensions, (Length x Depth x Height): 195 mm x 205 mm x 286 mm

Weight: 8.0 kg

Inlet/Outlet Thread Size: 1” BSP

Max Flowrate (subject to operator input): 22.50 L/min

Suction Lift: 7 m (at sea level)

Max Head: 25 m

Suitable for Pumping: Water, Oil or Diesel

DO NOT USE THIS PUMP WITH PETROL OR EDIBLE OILS

INSTALLATION

1. Remove connecting flanges (11) and remove the paper membranes

used to close off the inlet and outlet openings during transit.

2. Depending upon the intended use, it may be desirable to flush out any

residual oil from inside the pump.

3. Install the pump in a vertical position on a wall or similar

structure, with the outlet (indicated by the raised lettering

e.g. K2) facing upwards as shown (fixing bolts not supplied).

Also, always observe any arrows on the pump cover,

indicating the direction of flow.

• Vertical mounting is essential because the valves close

under gravity and if they cannot close, the pump cannot produce

suction.

4. Fit the wooden handle, by tapping gently to ensure it is a tight fit on the

handle spike. The handle can be repositioned to point in any direction

after removing the shaft end nut (9).

5. Connect any inlet and discharge hose connectors which are compatible

with the 1” BSP connecting flanges of the pump.

MAINTENANCE

1. Ensure that the seal compression nut (3) is sufficiently tight. If not, leakage

can take place from the pump handle shaft.

2. If using the pump for water, and there is a likelihood of freezing when not

in use, drain the pump via the access plug (15).

3. If the pump has been used for pumping any liquid likely to leave chemical

residues, it should be flushed through with clean water after use.

4. If the pump will be unused for extended periods, insert some oil through

the access plug (15) to protect the internal parts.

• Ensure the oil used does not contaminate the medium being pumped.

5. Periodically check that all nuts and bolts are tight.

A wide range of accessories are available from your nearest CLARKE dealer,

including hoses and hose adaptors and couplings.

COMPONENT PARTS

1. HTCRWP101 Flange Bolt & Nut 8. HTCRWP108 Gland Ring

2. HTCRWP102 Cover Bolt & Nut 9. HTCRWP109 Shaft End Nut

3. HTCRWP103 Seal Compression Nut 10. HTCRWP110 Washer

4. HTCRWP104 Wing Piston, Flap & Shaft 11. HTCRWP111 Conn Flange

5. HTCRWP105 Suction Divider, Flaps 12. HTCRWP112 Casing

6. HTCRWP106 Handle & Handle Spike 13. HTCRWP113 Cover

7. HTCRWP107 Gland Packing Set 14. HTCRWP114 Flange Joint

15. HTCRWP115 Access Plug

Table of contents

Other Clarke Water Pump manuals

Clarke

Clarke DWP100A Instruction Manual

Clarke

Clarke PSP195 Instruction Manual

Clarke

Clarke DW75 Instruction Manual

Clarke

Clarke HSE RANGE Instruction Manual

Clarke

Clarke HSE120 Installation and operation manual

Clarke

Clarke DW50 Instruction Manual

Clarke

Clarke PW50 Instruction Manual

Clarke

Clarke DFT230 Instruction Manual

Clarke

Clarke Hippo4A Instruction Manual

Clarke

Clarke CEB103 Instruction Manual

Clarke

Clarke CHF2 Installation and operation manual

Clarke

Clarke CM1 Installation and operation manual

Clarke

Clarke CPE30A1 Instruction Manual

Clarke

Clarke FP150 User manual

Clarke

Clarke CHHDP830 Instruction Manual

Clarke

Clarke DWP210A Instruction Manual

Clarke

Clarke CPE20A3 Instruction Manual

Clarke

Clarke HSE Series Installation and operation manual

Clarke

Clarke ECP20A3 Instruction Manual

Clarke

Clarke PTP100 Instruction Manual

Clarke

Clarke CSD4 Instruction Manual

Clarke

Clarke MSP12 User manual

Clarke

Clarke PF75A Instruction Manual

Clarke

Clarke CBT1300SS Instruction Manual

Popular Water Pump manuals by other brands

Neptun

Neptun NPHW 5500 operating instructions

Sensidyne

Sensidyne Gilian BDX-II Operation & service manual

Draper

Draper 47808 instructions

Trolla

Trolla 12820 manual

Sunfab

Sunfab SVH Series installation guide

WilTec

WilTec 50740 Operation manual

Fieldmann

Fieldmann FVC 5015 EK user manual

Everbilt

Everbilt EFSUB5-122HD Use and care guide

Graco

Graco Husky 3300e manual

esotec

esotec 101018 operating manual

moyno

moyno 2000 CC Service manual

Becker

Becker BASIC VASF 2.80/1-0.AC230 operating instructions

Sykes AmeriPumps

Sykes AmeriPumps GP100M Operation and maintenance instructions

DUROMAX

DUROMAX XP WX Series user manual

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 operating instructions

Franklin Electric

Franklin Electric IPS Installation & operation manual

Xylem

Xylem e-1532 Series instruction manual

Milton Roy

Milton Roy PRIMEROYAL instruction manual