Clarke HIPPO-3 Manual
OPERATING & MAINTENANCE
INSTRUCTIONS
6/97
SUBMERSIBLE
WATER PUMPS
Model Nos.
HIPPO-3 and 3A
2
Thank you for purchasing this CLARKE, HIPPO Submersible Pump.
These highly efficient pumps are designed for pumping clean water only, and are ideally
suited for draining ornamental ponds, swimming pools etc.Water temperature must not
exceed 35° C.
The HIPPO-3A differs from the HIPPO-3 in that it incorporates a float switch, which
automatically switches the pump OFF and ON when the water reaches a pre-determined
level.The minimum suction level being 5mm.Both models are available for use with 110V
and 230V supply’s.Please take note of the information regarding Electrical Installation .
Before attempting to operate your pump, please read this instruction manual thoroughly
and follow all directions carefully. This is for your own safety and that of others around
you, and to help you achieve long and trouble free service from your pump.
GUARANTEE
This product is guaranteed against faults in manufacture for 12 months from purchase
date.Keep your receipt as proof of purchase.This guarantee is invalid if the product has
been abused or tampered with in any way, or not used for the purpose for which it is
intended. The reason for return must be clearly stated. This guarantee does not affect
your statutory rights.
Please note that dismantling this pump will invalidate the guarantee
SAFETY PRECAUTIONS
1. These pumps are designed to pump CLEANWATER ONLY. Never use for pumping
flammable liquids or chemicals.
2. Never run the pump dry.
3. An approved Residual Current Device (RCD) MUST be used when pumping from
ponds or swimming pools.
4. Your submersiblepumpmayONLY beusedforpumpingwater from
a swimming pool when there is no person or animal in the pool.
5. Alwaysdisconnectthepump from the electrical supplybefore
placing it into, or removing it from the water, and before any
cleaning or maintenance of the pump.
6. Always use the moulded handle with a rope or cord attached
when lifting the pump.NEVER lift the pump by the mains
cable, or, where fitted, the float switch cable.
7. DO NOT run the pump with the body exposed for longer
than 10 minutes.
8. DO NOT install the pump on ground which is likely to shift.
9. Do not use the pump if the water is liable to freeze, as this can cause damage to the
pump.Remove the pump from the water and store it in a frost free location.
3
ELECTRICAL CONNECTIONS
230V models should have their mains lead connected to a standard 230Volt (50Hz)
electrical supply through an approved plug or a suitably fused isolator switch.
110V models should have their mains lead connected to a suitable 110V supply (50Hz)
through an approved plug or suitably fused isolator switch, or to a suitable portable 110V
transformer.
We recommend that these pumps be fitted with a Residual Current Device (RCD).
If the pump is to be connected to an outdoor electrical supply, make sure that both the
plug and the socket are of a BS approved waterproof design.
In the event that the pump is hard wired into the electrical system, it must be carried out
in accordance with IEE regulations.
If used for draining swimming pools or ponds, the pump MUST be fitted with a Residual
Current Device (RCD), with a rated residual operating current of no greater than 30mA.
WARNING:THIS APPLIANCE MUST BE EARTHED
230V only
IMPORTANT: The wires in the mains lead are coloured in accordance with the following
code: Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible cord of this appliance may not correspond with the coloured
markings identifying terminals in your plug proceed as follows:
Connect GREEN &YELLOW cord to plug terminal marked with a letter “E” or
Earth symbol “ “ or coloured GREEN or GREEN &YELLOW.
Connect BROWN cord to plug terminal marked with a letter “L” or coloured RED
Connect BLUE cord to plug terminal marked with a letter “N” or coloured BLACK
FUSE RATING
The fuse in the plug for this appliance must be rated at 13 amps.
If this appliance is fitted with a plug which is moulded onto the electric cable (i.e. non-
rewirable) please note:
1. The plug must be thrown away if it is cut from the electric cable.There is a danger of
electric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local dealer or most electrical
outlets
5. The fuse in the plug must be replaced with one of the same rating (13 amps) and
this replacement must be ASTA approved to BS1362.
IMPORTANT:If you are in any doubt regarding electrical installation, you should
consult a qualified electrician.
FEATURES
The pumps are of rugged and durable construction, designed for long lasting continuous
operation, and the motor is provided with a built in overload protector.
For your information, the chart on page 7 illustrates the flow rate at various heads.
(HEAD is the distance, or height, from the pump outlet to the highest point of discharge)
All models are designed for pumping CLEAN WATER ONLY and will pump down to a
water level of 5mm.
Automatic Pumps, i.e. those fitted with a Float Switch, denoted by an ‘A’ suffix to their
modelnumber, are suitablefor permanentorsemi-permanent installations,eg.installations
where it is necessary to maintain a water at a particular level.
As the water level rises, the switch will float, and start the pump.As the water level falls,
so will the float switch, until it stops the pump.
Float switches are factory set to provide the correct ON-OFF switching mode, however,
you can adjust the level at which the pump cuts out by sliding the float switch cable, in its
clip attached to the handle, to either shorten or lengthen it as the case may be. The
shorter it is, the earlier it will cut out and therefore, the deeper will be the water at this
point.
INSTALLATION
An Elbow Outlet is provided with a 1-1/4”BSP
thread at either end as shown in the diagram
opposite.Ensure the end provided with an O-Ring
is screwed into the pump outlet. Screwed into the
other end of the elbow, is a multi hose connector
capable of accepting 1”, 3/4” 0r 1/2” hose. Simply
attach a suitable hose to your preferred connector
with a worm drive clip.
If the pump is to be used for drainage purposes, or
in situations that demand maximum efficiency, we
stronglyrecommendthatyouconnecta1”dia.hose
4
5
to the multi hose adapter, preferably cutting off the other two stages at the groove at the
end of the 1” dia. step.
Alternatively, you may remove the multi adapter
altogether,andscrewona1-1/4”BSP hose adapter
as shown in fig.2.
The pump is completely submersible, and should
beplacedina verticalposition,on a solidflatsurface.
If this is not available, sit the pump a solid surface, eg. house bricks, but ensure they are
not likely to shift. IMPORTANT:
ALWAYS raise and lower the pump using a rope attached to the lifting handle, NEVER
by the power cable.
Automatic versions should be placed in a sump which has adequate dimensions so as
not to restrict the movement of the float switch.
Take all necessary precautions as described on page 2 before plugging in, and switching
ON.
SUITABLE HOSE, and SPARE/REPLACEMENT MULTI HOSE ADAPTERS ARE
AVAILABLE FROMYOUR CLARKE DEALER
MAINTENANCE
WARNING
Before checking the condition of the pump, ensure it is unplugged from the
mains supply. If the unit is hard wired, ensure the circuit breaker is open.
Check the pump installation regularly to ensure the base inlet is clear of leaves or other
debris.
If the pump has been used for pumping salt water, ensure it is flushed with clean mains
water thoroughly before storing.
Note that these pumps are fitted with automatic thermal overload protection.If the pump
overheats due to an obstruction in the pump, or pumping warm water for example, it will
shutoffautomatically.Switch the pump OFF and disconnect from the mainssupply.Check
for blockages and allow the motor to cool (at least 5 minutes) before attempting to re-
start.
These pumps should require no maintenance other than regular cleaning. If the pump
starts to show signs of wear or damage, contact your CLARKE dealer for advice.Do not
use the pump if there is any damage to the mains supply cable, or to the float switch or its
cable. Do not attempt to repair the pump yourself, as you may damage the waterproof
seal and invalidate your guarantee.Repairs must be carried out by your CLARKE dealer,
or contact the CLARKE Service Department, on 020 8988 7400
Fig. 2
Rubberwasher
Hoseadapter
TROUBLE SHOOTING
A. PUMPWILL NOT START
1. Manual type (i.e. without float switch)
1.1 Check to ensure Power is switched on.
1.2 Check fuse (consult an electrician if in doubt).
1.3 If extension lead is fitted, check connections (consult an electrician if in
doubt).
1.4 Internal thermal cut-out has not re-set. Leave for 5 minutes and try again.
1.5 The Impeller may be jammed. Disconnect from the mains supply, and
remove any objects that may be obstructing the impeller and try again.
If the pump still fails to start, consult your CLARKE dealer for advice.
2. AutomaticType (with float switch)
2.1 Check all above.
2.2 Float switch may be jammed against side wall, or prevented from moving.
2.3 Water level too low - float switch in OFF position - Lift float to check switch.
B. PUMPWILL START BUT NOT PUMP
1. Water level too low - below the minimum suction level (Manual type).
2. Check to ensure strainer is not blocked.
3. Discharge tube clogged or obstructed.
4. The head may be too great, i.e.you are trying to lift the water too great a distance
for the pump to cope with.(See specification chart page 7).
5. Air bubble in the pump, produced during the plunge.Plunge the pump again, at
an angle, and shake it whilst lowering to remove any air trapped in the system.
6. Impeller may be damaged - Consult your CLARKE dealer
C. AUTOMATIC PUMP WILL NOT STOP
1. Float switch may be prevented from moving to the fully down position.
2. Float switch may be faulty. Consult your CLARKE dealer for advice.
D. PUMP STOPS RUNNING
1. Thermal overload has operated. If this condition persists, investigate the cause.
REMEMBER: DO NOT attempt to pump anything other than CLEAN water.
2. Pump has run dry, or float switch has cut in.
3. A foreign object has jammed the impeller.
6
SPECIFICATIONS
Outlet Dia. ................................................. 1-1/4”
Motor Output ................................................. 220 Watts
Head Max. ................................................. 6 Metres
Max. Capacity ................................................. 100 L/min
Weight Hippo3 ..................................... 4.0 kg
Hippo3A................................... 4.2 kg
Dimensions ................................................. 140*x267mm
Part Nos. Hippo3 - 230V ......................... 7230500
Hippo3 -110V .......................... 7230520
Hippo3A - 230V ....................... 7230510
Hippo3A - 110V ....................... 7230530
* Pump diameter does not include elbow
7
SPARE PARTS & ACCESSORIES
Part No.
1. 1-1/4”x1-1/4” BSP Outlet Elbow See your dealer
2. O-Ring for Elbow LDP1200009
3. 1”BSP Multi Hose Adapter See your dealer
4. O-Ring for Multi Hose Adapter LDP1200002
5. 1” Hose Delivery - Lay flat 7955010
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
This manual suits for next models
1
Table of contents
Other Clarke Water Pump manuals
Clarke
Clarke HIPPO 2 Instruction Manual
Clarke
Clarke BIP1500 Instruction Manual
Clarke
Clarke DW75 Instruction Manual
Clarke
Clarke CPE Series Instruction Manual
Clarke
Clarke CD1 - 1 Installation and operation manual
Clarke
Clarke PW2 Installation and operation manual
Clarke
Clarke CFT230 Manual
Clarke
Clarke CSV4A Instruction Manual
Clarke
Clarke PSP105 Instruction Manual
Clarke
Clarke CRWP1 User manual
Clarke
Clarke TAM101 Installation and operation manual
Clarke
Clarke CPE30A1 Instruction Manual
Clarke
Clarke CPE20A3 Instruction Manual
Clarke
Clarke PSV5A Instruction Manual
Clarke
Clarke IVP13A Installation and operation manual
Clarke
Clarke CPRP560 Instruction Manual
Clarke
Clarke CBM100SS Installation and operation manual
Clarke
Clarke PF75 Instruction Manual
Clarke
Clarke PW50A Instruction Manual
Clarke
Clarke CPPRSS User manual
Popular Water Pump manuals by other brands
Sykes AmeriPumps
Sykes AmeriPumps GP100M Operation and maintenance instructions
DUROMAX
DUROMAX XP WX Series user manual
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 operating instructions
Franklin Electric
Franklin Electric IPS Installation & operation manual
Xylem
Xylem e-1532 Series instruction manual
Milton Roy
Milton Roy PRIMEROYAL instruction manual