Bosch PHANTOM EDGE User manual
PHANTOM
EDGE
Discover the World of IoT
Table of Contents
List of components
Phantom Edge overview
Installation steps
Technical specification
Safety instructions
Uninstallation and End-of-Life disposal instructions
3
4
5
12
13
13
1
2
3
4
5
6
Content Pg No.Sl No.
List of components
Sl. No. Item Quantity
1Phantom Sensor Device 1
2LTE Antenna 2
3Wi-Fi Antenna 1
4Current Transformer (CT) with Connector set of 3
5CT Cable Extender (Optional) 1
6Voltage Connection Cable with Connector 1
7Cable Ties 4
8Mounting Screws 4
9Contact and Warranty Card 1
10 Drill Paper Guide 1
1
6
2
7
3 4
8
5
10
9
Asset Name/No:
Asset Location:
Facility Contact:
Phone Number:
www.boschphantom.com
PHANTOM EDGE
03
PHANTOM
EDGE
PHANTOM EDGE View
2.1 Front View
EthernetLED
Indicator
Voltage
Input
CT Input RS-232 Differential
Pressure Element
LTE
Antenna 1
Micro
Sim Slot
2.2 Right View
2.3 Left View 2.4 Back View
MICRO SIM
LTE
Antenna 2
Wi-Fi
Antenna
DOUBLE
INSULATION
ELECTRICAL
HAZARD
DO NOT OPEN
AUTHORISED
PERSONNEL ONLY
CAUTION
Technical Specifications &
Manufacturer Details Label
Hardware ID
VOLTAGE INPUT CT INPUT
LTE 1
LTE 2 Wi-Fi
00001
RBSGS18121RI1V1R
04
a.
b.
Installation Steps
3.1 SIM Card Insertion(Optional)
Gently pull the flap on its right side
to reveal the Micro SIM card slot
MICRO SIM
MICRO SIM
Close the Micro SIM cap
and fasten firmly
Insert Micro SIM into Phantom Edge
as per the marking sticker
MICRO SIM
LTE 1
LTE 1
LTE 1
c.
05
If Wi-Fi connection is not available, use SIM card for it
Identify the location to mount Phantom Edge. Ensure that Phantom Edge is mounted
within 1 meter of radius from the point of CT installation.
Phantom Edge can be mounted in the following options:
a. b. c.
32mm
a. b.
3.2 Mounting
CT
Connection
PHANTOM
EDGE
Option A: Mount Phantom Edge in a horizontal direction using stickers
Peel off the cover layer from
the backside of Phantom Edge
Mount the device in a horizontal direction
by using adhesive surface of the stickers.
Use the Drill Paper Guide and
mark the four locations to
drill on the target wall
Mount the Phantom Edge on
the wall using the four screws
provided in the kit
Drill holes of sufficient depth
to accommodate M4 screw
provided in the installation kit
Option B: Mount Phantom Edge on a vertical surface using screws
06
PHANTOM
EDGE
3.3 Antenna Connection
MICRO SIM
LTE 2
LTE 1
LTE 1
Wi-Fi
LTE 2 Wi-Fi
a.
b.
c.
LTE 2
Insert LTE antenna 1 into LTE
antenna 1 port and rotate the
antenna nut in a clockwise
direction until it is firm.
Ensure not to overtighten.
Insert LTE antenna 2 into LTE
antenna 2 port and rotate the
antenna nut in a clockwise
direction until it is firm.
Ensure not to overtighten.
Insert Wi-Fi antenna into Wi-Fi
antenna port and rotate antenna
nut in a clockwise direction until it
is firm. Ensure not to overtighten.
07
Wi-Fi
Clamp CT around the
individual power cable for each
phase. Ensure that the front
surface of the CT and
line label, is oriented in the
direction of power source.
Ensure color code of the
power cable and line label
matches (Refer Exhibit 1).
b.
Towards
power supply
Direction
of power
flow
Towards load
Identify each CT by line 1, 2
& 3 label behind the CT
c.
b.a. c.
3.4 CT Connection
3.5 Voltage Connection
Line 1
Line 1
Line 2 Line 3
Voltage
Connection
VOLTAGE INPUT CT INPUT
VOLTAGE INPUT CT INPUT
a.
Connect the CT female
connector to the male
connector on Phantom Edge,
which is labelled as Current
Input
Identify the MCB switch
associated with relevant
electrical load/machine
Remove approx. 50mm of
insulation from wires.
Connect the four-individual
wire strands in the voltage
connector cable to the
appropriate points of the
four-pole MCB. Follow color
coding of the wire strands to
ensure correct connection
(Refer exhibit 1).
Connect the female connector
of this cable to the male
connector on Phantom Edge,
which is labelled as Voltage
Input
08
3.6 RS232 Connection(Optional)
RS232
3.7 Ethernet Connection(Optional)
VOLTAGE INPUT CT INPUT
Voltage
connection
Voltage
connection
VOLTAGE INPUT CT INPUT
RS232
Connection
Identify RS232 female connector
connected to machine PLC
Identify the recommended Amphenol
RJ45 Cable RCP-5SAMMM-SLM7Bxx
male connector connected to
machine PLC
Connect machine’s RJ45 ethernet male connector to the
RJ45 female port of Phantom Edge and rotate connector
nut in a clockwise direction to tighten it
Connect machine PLC RS232 female connector to the
male connector of Phantom Edge and tighten the screws
09
Use this option only If need to collect the data from a device using RS232 port
Use this option only If need to collect the data from a device using ethernet port
a. b.
a. b.
Use the cable ties to secure and bundle the cables
Fill in the contact details of local technician and tag it on the voltage cable.
Ensure all details are correctly filled for emergency response.
3.8 Tidy Up
Tidy Up
Voltage
Connection
RS232 Connection
Ethernet Connection
Tidy Up
Voltage
Connection
RS232 Connection
Ethernet Connection
10
a.
b.
PHANTOM
EDGE
PHANTOM
EDGE
Other manuals for PHANTOM EDGE
1
Table of contents
Other Bosch Measuring Instrument manuals
Bosch
Bosch PLR 50 User manual
Bosch
Bosch UniversalDistance 30 User manual
Bosch
Bosch LR 1 Professional User manual
Bosch
Bosch GLM 500 Professional User manual
Bosch
Bosch FAA-420-RI-ROW User manual
Bosch
Bosch DUS 20 plus User manual
Bosch
Bosch GLL 30 G User manual
Bosch
Bosch DLR130K User manual
Bosch
Bosch Quigo Green User manual
Bosch
Bosch GCL 25 Professional User manual
Bosch
Bosch GRL 300 HV User manual
Bosch
Bosch GLM165-10 Assembly instructions
Bosch
Bosch Rexroth CIMSmart User manual
Bosch
Bosch GLR225 Assembly instructions
Bosch
Bosch GLM 100 C Professional User manual
Bosch
Bosch GAM 220 MF Assembly instructions
Bosch
Bosch GLM Professional 250 VF User manual
Bosch
Bosch GLM 50 Professional User manual
Bosch
Bosch ETT 6.21 User manual
Bosch
Bosch GLM 20 Assembly instructions
