Black Box LB410A User manual

LB410A

LB411A

LBNC412A

High Speed Ethernet Extender

Extend 10/100Base-TX Ethernet up to 10,000 feet (3 km)

Over a single twisted-pair, Cat 5e/6/7, or even coaxial cable

724-746-5500 | blackbox.com

Page 2

Black Box Ethernet Extenders

TABLE OF CONTENTS

1. General Information .....................................................................................8

1.1 Features ..............................................................................................8

1.2 Description.......................................................................................... 8

2. Installation.................................................................................................... 9

2.1 Connecting the Line Interface ...........................................................11

Connecting the Line Interface for LB411A or LB410A........... 11

Connecting the Line Interface for LBNC412A........................ 12

2.2 Connecting the 10/100Base-T Ethernet Interface ............................ 12

2.3 Connecting Power ............................................................................ 13

3. Configuration ............................................................................................. 14

3.1 Configuring the Hardware DIP switches ...........................................14

3.2 Configuring DIP Switch S1 ............................................................... 14

Switch S1-1: Local/Remote Configuration............................. 15

Switches S1-2 and S1-3: Symmetric/Asymmetric Operation. 15

Switch S1-5: General Protection (Signal to Noise Ratio)....... 15

4. Operation................................................................................................... 16

4.1 Front Panel LED Status Monitors .....................................................16

A. Specifications............................................................................................. 17

A.1 LAN Connection ................................................................................17

A.2 Transmission Line .............................................................................17

A.3 Line Rate and Distance ....................................................................17

A.4 LED Status Indicators .......................................................................17

A.5 Power Supply ....................................................................................17

A.6 Temperature Range ..........................................................................17

A.7 Humidity ............................................................................................18

A.8 Dimensions .......................................................................................18

B. Factory Replacement Parts and Accessories............................................ 19

C. Ethernet Extender Interface Pin Assignment............................................. 20

C.1 10/100Base-T Interface ....................................................................20

RJ-45 ..................................................................................... 20

C.2 Line Interface ....................................................................................20

RJ-45 ..................................................................................... 20

Terminal Block....................................................................... 20

D. Line Rate & Reach Chart, Based on 24 AWG (0.5 MM)............................ 21

724-746-5500 | blackbox.com Page 3

RADIO FREQUENCY INTERFERENCE STATEMENTS

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO

FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested and

found to comply with the limits for a Class A computing device in accordance with the

specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection against such interference when the equipment is operated in a

commercial environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his own expense will be required to take

whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le Règle-

ment sur le brouillage radioélectrique publié par Industrie Canada.

724-746-5500 | blackbox.com

Page 4

Black Box Ethernet Extenders

INSTRUCCIONES DE SEGURIDAD

(Normas Oficiales Mexicanas Electrical Safety Statement)

5. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

6. Las instrucciones de seguridad y operación deberán ser guardadas para referen-

cia futura.

7. Todas las advertencias en el aparato eléctrico y en sus instrucciones de oper-

ación deben ser respetadas.

8. Todas las instrucciones de operación y uso deben ser seguidas.

9. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de

la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

10.El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

11.El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

12.Servicio—Elusuario no debe intentar dar servicioal equipo eléctrico más allá a lo

descrito en las instrucciones de operación. Todo otro servicio deberá ser referido

a personal de servicio calificado.

13.El aparato eléctrico debe ser situado de tal manera que su posición no interfiera

su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o

superficie similar puede bloquea la ventilación, no se debe colocar en libreros o

gabinetes que impidan el flujo de aire por los orificios de ventilación.

14.El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como

radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificado-

res) que producen calor.

15.El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo

descrito en el instructivo de operación, o como se indique en el aparato.

16.Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

17.Los cables de la fuente de poder deben ser guiados de tal manera que no sean

pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo par-

ticular atención a los contactos y receptáculos donde salen del aparato.

724-746-5500 | blackbox.com Page 5

INSTRUCCIONES DE SEGURIDAD

18.El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomenda-

ciones del fabricante.

19.En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

20.El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

21.Cuidado debe ser tomado de tal manera que objectos liquidos no sean derrama-

dos sobre la cubierta u orificios de ventilación.

22.Servicio por personal calificado deberá ser provisto cuando:

A. El cable de poder o el contacto ha sido dañado; u

B. Objectos han caído o líquido ha sido derramado dentro del aparato; o

C. El aparato ha sido expuesto a la lluvia; o

D. El aparato parece no operar normalmente o muestra un cambio en su desem-

peño; o

E. El aparato ha sido tirado o su cubierta ha sido dañada.

724-746-5500 | blackbox.com

Page 6

Black Box Ethernet Extenders

SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. This

device can only be repaired by qualified service personnel.

• Do not open the device when the power cord is connected.

For systems without a power switch and without an external

power adapter, line voltages are present within the device

when the power cord is connected.

• For devices with an external power adapter, the power

adapter shall be a listed Limited Power Source. The mains

outlet that is utilized to power the device shall be within 10

feet (3 meters) of the device, shall be easily accessible, and

protected by a circuit breaker in compliance with local regu-

latory requirements.

• For AC powered devices, ensure that the power cable

used meets all applicable standards for the country in

which it is to be installed.

• For AC powered devices which have 3 conductor power

plugs (L1, L2 & GND or Hot, Neutral & Safety/Protective

Ground), the wall outlet (or socket) must have an earth

ground.

• For DC powered devices, ensure that the interconnecting

cables are rated for proper voltage, current, anticipated

temperature, flammability, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazard-

ous voltages present regardless of whether the device is

powered ON or OFF. PSTN relates to interfaces such as

telephone lines, FXS, FXO, DSL, xDSL, T1, E1, ISDN, Voice,

etc. These are known as “hazardous network voltages” and

to avoid electric shock use caution when working near

these ports. When disconnecting cables for these ports,

detach the far end connection first.

• Do not work on the device or connect or disconnect

cables during periods of lightning activity.

WARNING

724-746-5500 | blackbox.com Page 7

Safety When Working With Electricity

In accordance with the requirements of council

directive 2002/96/EC on Waste of Electrical and

Electronic Equipment (WEEE), ensure that at

end-of-life you separate this product from other

waste and scrap and deliver to the WEEE col-

lection system in your country for recycling.

This device contains no user serviceable parts.

This device can only be repaired by qualified

service personnel.

This device is NOT intended nor approved for

connection to the PSTN. It is intended only for

connection to customer premise equipment.

Electrostatic Discharge (ESD) can damage

equipment and impair electrical circuitry. It

occurs when electronic printed circuit cards are

improperly handled and can result in complete

or intermittent failures. Do the following to pre-

vent ESD:

• Always follow ESD prevention procedures

when removing and replacing cards.

• Wear an ESD-preventive wrist strap, ensuring

that it makes good skin contact. Connect the

clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages

to ground.

• To properly guard against ESD damage and

shocks, the wrist strap and cord must operate

effectively. If no wrist strap is available, ground

yourself by touching the metal part of the chas-

sis.

WARNING

724-746-5500 | blackbox.com

Page 8

Black Box Ethernet Extenders

1. GENERAL INFORMATION

Thank you for your purchase of this Black Box product. This product has been thor-

oughly inspected and tested and is warranted for one year for parts and labor. If any

questions or problems arise during installation or use of this product, contact Black

Box Technical Support at +1 (301) 975-1007.

1.1 FEATURES

• Variable rate extender - Easy to configure

• Auto-MDIX Ethernet

• Configurable 10/100, Full/Half, and Auto-Negotiating Ethernet

• Extends up to 4x 10/100Base-TX Ethernet beyond 328-foot (100-meter) limita-

tion over a single twisted-pair, Cat 5e/6/7, or coaxial cable

• Symmetric or asymmetric settings via DIP switch

• Transparent operation

• LED indicators for Power, DSL Link, Ethernet Link/Activity, Remote and Local

1.2 DESCRIPTION

The Black Box Ethernet Extenders provide high-speed LAN connections between

peered Ethernet LANs, remote PCs, or any other network-enabled 10/100Base-T

device.

Operating in pairs, one Ethernet Extender is configured as the (L) Local unit located at

one end of the LAN extension and the other Ethernet Extender is configured as the (R)

Remote unit at the other end. The Ethernet Extender is configured as a L or R via the

switch on the bottom of the unit. These units can automatically forward LAN broad-

casts, multicasts, and frames across a 2-wire voice-grade twisted-pair or BNC link.

The data is passed transparently (unmodified) through the Ethernet Extenders. The

Ethernet Extenders automatically add and delete MAC addresses, only passing pack-

ets across the line link that are meant for the remote peered LAN.

724-746-5500 | blackbox.com Page 9

Installation

Figure 1. Typical application

The pair of Ethernet Extender models work together to create a transparent extension

between two peered Ethernet LANs using twisted pair (2-wire), Cat5+, or 75-ohm

BNC. Figure 1. shows a typical point-to-point application.

2. INSTALLATION

To install the Ethernet Extender, do the following:

1. Connect the line interface between the units (refer to section 2.1, “Connecting the

Line Interface” on page 11)

NOTE: See Figure 2. for the Ethernet Extender’s rear panel arrangements.

2. Connect the Ethernet interface (refer to section 2.2, “Connecting the 10/100Base-

T Ethernet Interface” on page 12).

3. Connect the power plug (refer to section 2.3, “Connecting Power” on page 13).

The Interconnecting cables shall be acceptable

for external use and shall be rated for the

proper application with respect to voltage, cur-

rent, anticipated temperature, flammability, and

mechanical serviceability.

CAUTION

724-746-5500 | blackbox.com

Page 10

Black Box Ethernet Extenders

Figure 2. Ethernet Extender rear panel options

Eth3

Eth0 Eth1 Eth2

12VDC 1A

Eth3

Eth0 Eth1 Eth2

12VDC 1A

Eth3

Eth0 Eth1 Eth2

12VDC 1A

This manual suits for next models

Table of contents

Other Black Box Network Hardware manuals

Black Box

Black Box JPM806A-HD User manual

Black Box

Black Box EME149A-20 User manual

Black Box

Black Box ME1240A-F User manual

Black Box

Black Box Balun G.703 User manual

Black Box

Black Box USB Director RS-232 User manual

Black Box

Black Box ACR2005A User manual

Black Box

Black Box DTX5000-CTL-R2 User manual

Black Box

Black Box 37688-R2 User manual

Black Box

Black Box IC240A User manual

Black Box

Black Box TL572A User manual

Black Box

Black Box COE-8I User manual

Black Box

Black Box AC1003A User manual

Black Box

Black Box MT619A-ST-R2 User manual

Black Box

Black Box PI1375A User manual

Black Box

Black Box MT190A User manual

Black Box

Black Box ServSwitch KV1081A User manual

Black Box

Black Box MX325A-HS User manual

Black Box

Black Box 38892-R2 User manual

Black Box

Black Box IT Pro LNA1000A User manual

Black Box

Black Box RADIAN 1000 Series User manual

Black Box

Black Box FOM Line Driver-ST User manual

Black Box

Black Box JPM083A-R3 User manual

Black Box

Black Box V.35 FOLD-ST Series User manual

Black Box

Black Box LT2060A User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide