BIONIME Rightest GM700 User manual
1) Press and release main button " " to turn on the Meter.
2) Press and hold main button " " for seven seconds until you go into the setting mode. Before
you go into setting mode, you will see power off first. Please keep pressing it until you go into the
setting mode. The year will flash.
3) Press up button " " or down button " " to change the year.
4) Press main button " " to confirm the year and move to month setting.
2
Main Button ( )
Press to turn on/off
meter or go into
setting model.
Auto Code Key
Auto Code Release Button:
Please contact the local
service for help, if needing to
change the auto code key.
Test Strip Port:
Insert test strip here until
you hear a click.
Battery Cover:
Slide cover to
change batteries.
Test strips vial Control Solution
Lancing Device
Lancet
Down Button ( )
For operating the
meter, please check
details in following
sections.
Batteries Installation
1
1) Turn the meter over. Press and push battery cover to open.
2) Install the battery. Be sure to put battery in correct direction.
3) Slide the battery cover back until it snaps into place.
3Setting Up Your Meter - Set the Date, Time, Volume and Measurement Unit
Auto code key has the function of auto-coding. The meter can automatically detect the code number
on strip, and hence it is no need to change code key unless it’s malfunctioned.
Auto Code Key
Front View of Meter Back View of Meter
Test strips
Sample Entry
View Window
Protective cover
5) Repeat steps 3 and 4 to change the date, time format, hour, minute and measurement unit.
After pressing the main button to confirm the measurement unit, your set-up has been finished.
Up Button ( )
For operating the
meter, please check
details in following
sections. 1 2
PlungerHubLancet carrier
Release button
Safe switch
Depth adjustable cap
GM700 GETTING STARTED GUIDE ( For self-testing )
Display Window:
Show your test result,
messages and relative
information.
NOTE
- Please contact the local service for help, if needing to change the auto code key.
3.0µ 4.01.0µ 1.5µ 2.0µL L L L µL
Performing a Test
4) Twist off and set aside the protective cover of the disposable lancet.
5) Replace the depth adjustable cap.
6) Choose a depth of penetration by rotating the top portion of the depth adjustable cap until the
setting depth matches the window. Settings are based on skin type
” “ for soft or thin skin;
” “ for average skin;
” “ for thick or calloused skin.
7) Hold the hub in one hand and pull on the plunger in the other hand. The device will be cocked.
Release the plunger, it will automatically move back to its original position near the hub.
5
1) Wash and dry your hands. Take one strip from the vial. Close the vial cap immediately.
2) Insert the strip into the strip port on meter with the indication symbol facing up. Push the strip in
until it clicks and stops. The meter will automatically detect code number.
3) When you see the flashing blood drop, hold the lancing device to side of your fingertip and press
the release button.
4) The Meter only needs a tiny blood sample. Please take a minimum of 1.0µL to do the test on
blood glucose monitoring system. Blood sample size above 3.0µL might contaminate the meter.
Not enough blood (<1.0µL) might cause inaccurate result.
5) Touch and hold the drop to the edge of sample entry until you hear a " beep " and the view
window is totally filled with blood. If the view window is not totally filled with blood, the test might
not start. Then discard the test strip and repeat the test with a new test strip.
6) You will see the countdown mode on the screen. After 5 seconds, the test result appears. For
more information, please check your User Manual for details.
7) Remove the test strip from meter. Please follow the local regulation and discard the used strip
properly.
For more information on how to use your meter and understand your test results,
please see the User Manual.
BIONIME CORPORATION
694, Renhua Road, Dali Dist,
Taichung City 412, Taiwan
Tel: 886-4-24951268 Fax: 886-4-24952568
Email: [email protected]
Website: www.bionime.com
4 6 7
8
12
9 10 11
8) Pull off the depth adjustable cap. Without touching the used disposable lancet, stick the lancet
tip into the protective cover.
9) Hold the release button in one hand and pull on the plunger in the other hand will safely eject
the used disposable lancet.
10) Discard the used disposable lancet into an appropriate puncture-proof or biohazard container.
11) Replace the depth adjustable cap after finishing the test.
Bionime GmbH
Tramstrasse 16
9442 Berneck
Switzerland
5
57
Sample Size Example
4
4
1) Hold the adjustable cap in one hand and hold the hub in the other hand. Bend the cap towards
the down side. When a gap appears between the cap and hub, pull them off in opposite
directions.
2) Pull off the depth adjustable cap.
3) Insert a new disposable lancet firmly into lancet carrier.
Preparing the Lancing Device
1 2 3
6
1 2 3
101-3GM700-010
EN
Rev. Date : May/2012
Other manuals for Rightest GM700
1
