BI COMMUNICATIONS TX8000 User manual
TX8000
Quick Start
Operating Instructions
Ranges meters 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 6km
feet 23, 49, 98, 197, 394, 820, 1640, 3280, 6560, 9850, 19000
Range Selec on Manual range control
Dual cursors with a distance measurement between cursors
Accuracy 1% of selected range*
Resolu on Approx 1% of range
Sensi vity Min 3 pixel return at 4km on 0,6mm Æ , PE , TP
Velocity Factor Adjustable from 1% to 99%
Output Pulse 5 volts peak to peak. Into open circuit
Output Impedance Selectable 25, 50, 75 & 100 ohms
Output pulse Width 3 ns to 3 ms, Automa c with range
Scan Rate 2 scans / second or scan held
Tone Generator 810 – 1100Hz
Ba ery Life 7 hours typical use
Power Supply 6 volts, 4 x 1.5 AA Alkaline cells
Power Down Selectable 1, 2, 3, 5 minutes or disabled
Back Lit Display and keyboard (Display 320x240 QVGA)
Voltage Detec on 250 volts AC
Opera ng Temp -10º / 50ºC
Storage Temp -20º / 70ºC
Dimensions 220x98x58 mm
Weight 0.5 Kg
Safety IEC 61010-1
EN 60950
EMC BS/EN 61326-1
Protec on Class IP67
Technical Specifi ca on
The TX8000 is 6Km range Time Domain Refl ectometer housed in
a rugged over moulded case being water proof to IP67 and drop
resistant, designed for outside use, but suffi ciently small and light
weight for widespread use. Using a 3.5-inch QCGA colour display
informa on is clearly displayed; an illuminated key pad makes the
TX8000 ideal for use in poorly lit areas.
Using 11 range scales with a fi rst range of 7 meters near end
faults are clearly visible. Using the scan hold facility faults may be
retained on screen for closer examina on or when in scan mode
intermi ent faults may be easily iden fi ed. The user variable gain
control allows small events on the waveform to be magnifi ed for
clearer iden fi ca on. With dual cursors each cursor giving its
length measurement and a diff eren al distance between cursors
the length of a fault may be iden fi ed. To assist in the iden fi ca-
on of faults a number of known fault types may be super im-
posed over the displayed fault for easier iden fi ca on
4 5
Replacing Ba eries
Remove 4 fi xing screws and li of cover. Remove
ba eries and replace with either 4 x AA Alkaline
ba eries or Nickel Metal Hydride (rechargeable).Ensure
correct polarity when refi ng. Refi t cover and screws.
1. To commence trace
2. Escape to exit TDR mode
3. Increase se ng
4. Cursor right/Op on
5. On/Off and keyboard light
6. Decrease se ng
7. Cursor le /Op on
8. Enter to save selected se ng
and select ac ve cursor
9. Set/Sel to select screen op ons
BEFORE USE READ THE FULL INSTRUCTION MANUAL
WHICH IS AVAILABLE TO DOWNLOAD FROM OUR
WEBSITE.
www.bicommunica ons.co.uk
DO NOT USE ON LIVE OR ACTIVE CIRCUITS
9
Opera on
Power ON – Press key (5) and release, Power OFF
press key (5) and hold for 2 seconds
Key Pad Illumina on- press key (5) to Turn on/off .
If the unit is fi ed with new ba eries, or the ba eries
have been removed and refi ed a message will appear
for the user to select the ba ery type press keys (3 / 6)
to highlight the ba ery type, press key (9) to select.
The main menu –
1. Measurements
2. Se ngs
3. Help
To select a menu op on, use keys (3 / 6) to highlight,
press key (8) to select.
Measurements this is the measurement screen, the
parameters listed below are displayed along the top
and the right-hand side of the display these may be
changed as follows,
to select Press key (5) un l parameter is highlighted
press keys (3 / 6) to change value
Impedance – selectable for 25,50,75 and 120
ohms
VoP- selectable between 1 and 99% or feet/
meters per microsecond
RANGE-Selectable from 7meters to 6Km or Feet
(11 range scales)
Scan mode select between Cont, Once or Tone
CURSOR MODES C1, C2 – The TDR can be operated on
single cursor C1 (RED) or dual cursor C2 (GREEN), to
move the cursor to fault posi on on cable use keys (4/
7). When in Dual cursor mode keys (4/7) default to C1
cursor. To change between cursors, press (8). A small
arrow will be shown on the top of the selected cursor.
The distance between cursors is displayed in bo om
right of display.
GAIN To change gain value press keys (3/7)
?A range of fault condi ons may be superimposed on
the screen, to scroll through these Press keys (3/6)
To exit TDR mode – Press key (2),
SETTINGS MENU
VoP unit, % or meters / feet per m/s
Length unit, meters or feet (the VoP will be displayed in
the unit selected)
Display brightness, high, medium or low
Auto Shutdown, disabled or 1,3,5,10,15, minutes
Language, English, Polish, German and Spanish
Press keys (3 / 5) to highlight op on, keys (4 / 7) to
change se ng, to exit screen press key (2)
HELP This lists a number of cable types with their
impedance and VoP values
1 2 3
Other manuals for TX8000
1
Other BI COMMUNICATIONS Measuring Instrument manuals
