BGS technic 8482 User manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8482

Ball Joint Tool for BMW 3 Series

A professional quality tool designed for easy removal and insertion of press fit control arm ball joints

Suitable for use on BMW 3 series (E36) models

1. Press Frame Assembly

2. Removal Shell

3. Installation Shell

4. Drive Screw with Thrust Bearing

5. Spindle Support

6. Support

7. Removal Bush

8. Installation Bush

WARNING

Before starting work under a car always ensure that it is adequately supported by axle stands or

ramps.

Chock wheels and ensure that the hand brake is firmly applied.

Always work in a well ventilated area.

Always use approved eye protection especially when working under vehicles.

Ensure that tools are correctly mounted.

Always use workshop manual for detailed instructions.

Do not over tighten or use undue force as this can cause damage to both tool and component.

Always lubricate screw thread.

Do not use an impact wrench with this tool

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Extraction Insertion

A = Bush

1. Securely support the vehicle and follow workshop manual instructions to access the ball joint.

Mark the position of the ball joint to ensure the new ball joint is correctly installed.

2. Ensure that the screw threads (4) are clean, in good condition and freely lubricated each time

before use.

3. To remove the old ball joint assemble the tool as shown, using the bright plated shells (2) &

(7). Note ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to

slowly turn the drive screw (4) to extract the ball joint from the control arm.

4. Clean the lower face & bore of the control arm using a wire brush to remove any rust. Do not

apply any grease to the bore or the ball joint taper.

5. To install the new ball joint assemble the tool as shown, using the shells (8) & (3). Note:

ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to slowly turn

the drive screw (4) to insert the ball joint into the control arm. Always lubricate the screw

threads before using the tool.

Table of contents

Other BGS technic Tools manuals

BGS technic

BGS technic 8846 User manual

BGS technic

BGS technic 3286 User manual

BGS technic

BGS technic 70325 User manual

BGS technic

BGS technic 3294 User manual

BGS technic

BGS technic 67310 User manual

BGS technic

BGS technic BGS 2999 User manual

BGS technic

BGS technic 8474 User manual

BGS technic

BGS technic 6667 User manual

BGS technic

BGS technic 3324 User manual

BGS technic

BGS technic 65630 User manual

BGS technic

BGS technic 9605 User manual

BGS technic

BGS technic 9379 User manual

BGS technic

BGS technic 9868 User manual

BGS technic

BGS technic 9465 User manual

BGS technic

BGS technic 98253 User manual

BGS technic

BGS technic 70205 User manual

BGS technic

BGS technic 8676 User manual

BGS technic

BGS technic 62622 User manual

BGS technic

BGS technic 3201 User manual

BGS technic

BGS technic 8954 User manual

BGS technic

BGS technic 1124 User manual

BGS technic

BGS technic 8690 User manual

BGS technic

BGS technic 62637 User manual

BGS technic

BGS technic 3380 User manual

Popular Tools manuals by other brands

Martor

Martor SECUNORM 175 quick start guide

ERKCO

ERKCO 1000 user manual

jbc

jbc N4473 instruction manual

FEINMETALL

FEINMETALL FZWZ-SET-001 quick start guide

Worx Professional

Worx Professional Sonicrafter WU676 Original instructions

Gage Bilt

Gage Bilt GB713SH Original instructions

Hilti

Hilti DX 9-ENP Original operating instructions

norbar

norbar NORTRONIC 34399 Operator's manual

Makita

Makita DHR241 instruction manual

Motor Guard

Motor Guard JMB-1250 instructions

Power Adhesives

Power Adhesives 805-12 operating instructions

Clemco

Clemco 24189 quick start guide

VVG

VVG VNG 903 Series instruction manual

Hilti

Hilti FX 3-A operating instructions

Grizzly

Grizzly H6472 Manual insert

axing

axing BWZ 5-02 Operation instructions

Dh-Robotics

Dh-Robotics RGI-100 Short manual

Goobay

Goobay 97790 user manual