Bedrock UTA.CN User manual

Revision 3 February 2020

Bedrock UTA

User Manual

Contents

2/6/20 Bedrock UTA User Manual - BRDOC150_003 i

Contents

Disclaimer.........................................................................iii

Bedrock UTA Overview....................................................... 1

Introduction.............................................................................................................1

UTA Offerings .........................................................................................................1

UTA.CN.......................................................................................................................4

UTA.CP .......................................................................................................................6

UTA.CF........................................................................................................................8

UTA.CDO..................................................................................................................10

UTA.CDI05M1..........................................................................................................12

UTA.CDI05S1 ...........................................................................................................14

UTA.CDI10M1..........................................................................................................16

UTA.CDI10S1 ...........................................................................................................18

UTA Installation and Operation ........................................ 20

Mounting UTAs.....................................................................................................20

IO Connections .....................................................................................................20

Grounding..............................................................................................................21

UTA.CN with Two Wire Devices........................................................................22

UTA.CN with Three or Four Wire Devices.......................................................23

UTA.CP with Two Wire Devices.........................................................................24

UTA.CP with Three or Four Wire Devices........................................................25

UTA.CF with Two Wire Devices.........................................................................26

UTA.CF with Three or Four Wire Devices........................................................27

Terminal Marker Strips ........................................................................................28

UTA.CDO ..............................................................................................................30

UTA.CDI05M1......................................................................................................31

UTA.CDI05S1........................................................................................................32

UTA.CDI10M1......................................................................................................33

UTA.CDI10S1........................................................................................................34

UTA Servicing and Troubleshooting ................................... 35

UTA.CF...................................................................................................................35

UTA.CDO ..............................................................................................................36

UTA.CDI05M1......................................................................................................37

UTA.CDI05S1........................................................................................................38

UTA.CDI10M1......................................................................................................39

UTA.CDI10S1........................................................................................................40

Contents

ii Bedrock UTA User Manual - BRDOC150_003 2/6/20

UTA Simplified Wiring Diagrams .........................................A-1

UTA.CN....................................................................................................................1

UTA.CP ....................................................................................................................2

UTA.CF.....................................................................................................................3

UTA.CDO ................................................................................................................4

UTA.CDI05M1........................................................................................................5

UTA.CDI05S1..........................................................................................................6

UTA.CDI10M1........................................................................................................7

UTA.CDI10S1..........................................................................................................8

Part Numbers ..........................................................................B-1

UTA Specifications..................................................................C-1

Electrical Specifications..........................................................................................1

Physical Specifications............................................................................................3

Environmental Specifications................................................................................4

Certifications.......................................................................... D-1

CE Testing ................................................................................................................1

Underwriters Laboratories (UL) Safety Certification ........................................1

ETL Listing (Intertek) Safety Certification ..........................................................2

2/6/20 Bedrock UTA User Manual - BRDOC150_003 iii

Disclaimer

Equipment, Diagrams, Hardware, and Software

Solid state equipment has operational characteristics differing from those of electromechanical equipment. Since there are a wide variety

of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended

application of this equipment is acceptable. In no event will Bedrock Automation be responsible or liable for indirect or consequential

damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements

associated with any particular installation, Bedrock Automation cannot assume responsibility or liability for actual use based on the

examples and diagrams.

No patent liability is assumed by Bedrock Automation with respect to use of information, circuits, equipment, or software described in

this manual.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

No Warranties

This manual is provided “as is” without any representations or warranties, express or implied. Bedrock Automation makes no

representations or warranties in relation to this manual or the information and materials provided herein. Although we make a reasonable

effort to include accurate and up to date information, without prejudice to the generality of this paragraph, Bedrock Automation does

not warrant that:

•The information in this manual is complete, true, accurate or non-misleading.

The Bedrock UTA User Manual is provided solely for informational purposes. You should not act upon information without consulting

Bedrock Automation.

Subject to Change

The Bedrock UTA User Manual is subject to change without notice.

Exceptions

Nothing in this disclaimer will exclude or limit any warranty implied by law that it would be unlawful to exclude or limit; and nothing in

this disclaimer will exclude or limit Bedrock Automation’s liability in respect of any:

• death or personal injury caused by Bedrock Automation’s negligence;

• fraud or fraudulent misrepresentation on the part of Bedrock Automation; or

• matter which it would be illegal or unlawful for

Bedrock Automation

to exclude or limit, or to attempt or purport to exclude or

limit, its liability.

Reasonableness

By using this manual, you agree that the exclusions and limitations of liability set out in this disclaimer are reasonable. If you do not

think they are reasonable, you must not use this manual.

Other Parties

You accept that, Bedrock Automation has an interest in limiting the personal liability of its officers and employees. You agree that you

will not bring any claim personally against Bedrock Automation’s officers or employees in respect of any losses you suffer in connection

with the manual.

Unenforceable Provisions

If any provision of this disclaimer is, or is found to be, unenforceable under applicable law, that will not affect the enforceability of the

other provisions of this disclaimer.

Manual Reproduction

Reproduction of the contents of this manual, in whole or in part, without written permission of Bedrock Automation, is prohibited.

Chapter 1

2/6/20 Bedrock UTA User Manual - BRDOC150_003 1

Bedrock UTA Overview

Introduction Bedrock Universal Termination Assemblies (UTAs) provide universal wiring

solutions for the interconnection of analog and discrete I/O signals to specific

Bedrock SIO modules, the OSA® Remote, and the OSA® Remote +Flow.

Bedrock UTAs are designed to simplify control panel design, reduce wiring

requirements, and provide project cost savings. UTAs provide solutions to

requirements such as voltage isolation, commissioning and servicing disconnects,

supplemental fusing, and expanded load currents. This guide contains installation

instructions, wiring diagrams, wiring examples, and reference information for

Bedrock UTAs.

All Bedrock UTAs provide the following features for conveniently connecting

supported Bedrock IO hardware to field devices.

• One or two twenty pin connectors provide connection to supported

Bedrock IO hardware using the Bedrock Dual-head Universal Cable.

• Banks of screw terminals provide connections to field devices.

• A grounding screw provides a location for attaching the drain wires of

Dual-head Universal Cables. This allows the shield of the cable to be

continued.

• A bank of terminals at the front of the UTA allows the cable’s shield

to be continued to field devices.

• Mounting is on a standard 35 mm x 7.5 mm DIN Rail.

UTA Offerings Bedrock UTAs are available in the models listed in Table 1-1.

Table 1-1 UTA Offerings

UTA Part Number UTA Model Description

BRUTA00N UTA.CN

Universal 20 Channel, Channel Isolated without Power Distribution

The UTA.CN provides direct point-to-point pass-through and is

intended for use with signals directly connected to the I/O modules

or with devices powered in the field. Labeling on the terminals

corresponds to pins on the IO module. Additional labeling on the

UTA circuit board corresponds to IO channels.

Chapter 1 Bedrock UTA Overview

2 Bedrock UTA User Manual - BRDOC150_003 2/6/20

BRUTA00P UTA.CP

Universal 10 Channel, Group Isolated with Power Distribution

The UTA.CP provides the functionality of the UTA.CN with the

added capability of providing field power distribution at the UTA via

two power terminals. Labeling on the terminals corresponds to

pins on the IO module. Additional labeling on the UTA circuit board

corresponds to IO channels.

BRAUTAAU UTA.CF

Universal Fused, 5 or 10 Channel, Channel Isolated

The UTA.CF is intended for input or output with field voltage

sources less than 30 V dc. The UTA.CF works with all OSA

Remote and OSA Remote +Flow models and analog and discrete

SIO modules that support low voltage.

Each channel has a 1 A, fast blow, removable fuse that provides a

point of service disconnect.

BRAUTADO UTA.CDO

Universal 5 Channel, Discrete Output, Group Isolated

The UTA.CDO provides 5 channels of discrete output for switching

field loads of 120 V ac and up to 1 A per channel. The UTA.CDO

works with all OSA Remote and OSA Remote +Flow models and

the SIOU.10 module.

Each channel has a 1 A, normal blow, removable circuit breaker

that provides a point of service disconnect in the enclosure. Each

channel also has a compact 24 V dc power relay that isolates the

system side from the field high voltage.

The state of the circuit breaker can be read back on the SIOU.10

Mapping tab in the Bedrock IDE.

BRTDI05M UTA.CDI05M1

Universal Termination Assembly, 5 Channel, 120 V ac Voltage

Monitor Discrete Input

The UTA.CDI05M1 can accommodate 5 channels of discrete input

for monitoring field voltage sources of 120 V ac. The

UTA.CDI05M1 works with all OSA Remote and OSA Remote

+Flow models and the SIOU.10 module.

Each channel has a user serviceable fuse with a blown fuse

indicator LED.

BRTDI05S UTA.CDI05S1

Universal Termination Assembly, 5 Channel, 120 V ac Contact

Sense Discrete Input with External120 V ac Power Input and

Distribution

The UTA.CDI05S1 is a dedicated termination solution for 120 V ac

contact sensing applications. The UTA.CDI05S1 works with all

OSA Remote and OSA Remote +Flow models and the SIOU.10

module.

Each channel has a user serviceable fuse with a blown fuse

indicator LED. A 120 V ac input power fuse assembly is provided

with blown fuse and power available indication.

Table 1-1 UTA Offerings

UTA Part Number UTA Model Description

Bedrock UTA Overview Chapter 1

2/6/20 Bedrock UTA User Manual - BRDOC150_003 3

For the types of Bedrock IO listed in Table 1-2, the usage matrix shows the

number of available IO channels as well as the number of dual-headed IO

cables and number of each type of UTA required to accommodate all IO

channels for that IO module. See “IO Connections” in “UTA Installation and

Operation” for more information on the dual-headed IO cable.

BRTDI10M UTA.CDI10M1

Universal Termination Assembly, 10 Channel, 120 V ac Voltage

Monitor Discrete Input with External 24 V dc Power Input and

Distribution.

The UTA.CDI10M1 is a dedicated termination solution for

120 V ac voltage input monitoring applications. The UTA.CDI10M1

is designed to work only with the SIO7.20 module.

Each channel has a user serviceable fuse with a blown fuse

indicator LED. A 24 V dc input power fuse assembly is provided

with blown fuse and power available indication.

BRTDI10S UTA.CDI10S1

Universal Termination Assembly, 10 Channel, 120 V ac Contact

Sense Discrete Input with External 120 V ac and 24 V dc Power

Inputs and Distribution

The UTA.CDI10S1 is a dedicated termination solution for 120 V ac

contact sensing input applications. The UTA.CDI10S1 is designed

to work only with the SIO7.20 module.

Each channel has a user serviceable fuse with a blown fuse

indicator LED. A 120 V ac input power fuse assembly for field

power and a 24 V dc input power fuse assembly for the SIO input

circuit are also provided. Both have blown fuse and power

available indication.

Table 1-1 UTA Offerings

UTA Part Number UTA Model Description

Table 1-2 UTA/UCD Usage Matrix

UTA Model

SIOU.10

SIO1.5

SIO2.10

SIO3.10

SIO5.10

SIO6.20

SIO7.20

SIO8.20

OSA Remote

R.10

OSA Remote

R.20

OSA Remote

+Flow F.10

OSA Remote

+Flow F.20

Channels 10 5 10 10 10 20 20 20 10 20 10 20

IO Cables 2 1 1 1 1 2 2 2 2 4 2 4

UTA.CN 1 1 1 1 1 1 1 1 1 2 1 2

UTA.CP 2 1 1 1 — 2 2 2 2 4 2 4

UTA.CF 2 1 1 1 1 2 2 2 2 4 2 4

UTA.CDO 2 — — — — — — — 2 4 2 4

Chapter 1 Bedrock UTA Overview

4 Bedrock UTA User Manual - BRDOC150_003 2/6/20

UTA.CN The top and side views of the UTA.CN, with two twenty-pin IO connectors,

are shown in Figure 1-1. The figure also shows the dimensions of the UTA.CN.

Figure 1-1 UTA.CN Top and Side Views

UTA.CDI05M1 2 — — — — — — — 2 4 2 4

UTA.CDI05S1 2 — — — — — — — 2 4 2 4

UTA.CDI10M1 — — — — — — 2 — — — — —

UTA.CDI10S1 — — — — — — 2 — — — — —

Table 1-2 UTA/UCD Usage Matrix

UTA Model

SIOU.10

SIO1.5

SIO2.10

SIO3.10

SIO5.10

SIO6.20

SIO7.20

SIO8.20

OSA Remote

R.10

OSA Remote

R.20

OSA Remote

+Flow F.10

OSA Remote

+Flow F.20

96 mm

128 mm

86 mm

This manual suits for next models

Table of contents

Other Bedrock Industrial Equipment manuals

Bedrock

Bedrock UPS.500 User manual

Bedrock

Bedrock OSA Remote Manual

Bedrock

Bedrock UPS.500 User manual

Popular Industrial Equipment manuals by other brands

ABB

ABB Unifix AD Instruction handbook

Mark 7

Mark 7 Evolution user manual

Husky

Husky HyPET Original instructions

bora

bora PM-1800 user manual

Grizzly

Grizzly T32428 owner's manual

Siemens

Siemens 8MF1 Series operating instructions

ABB

ABB HT610965 Operation manual

ABB

ABB SafeLink Installation and operating instructions

Phoenix

Phoenix PHX-150 user guide

ABB

ABB A165-L32 Operation manual

ABB

ABB HT842936 Operation manual

Rioned

Rioned UrbanJet user manual

Hermetica

Hermetica 10 Series user manual

HORNER

HORNER OEE Solution manual

Hammerhead

Hammerhead HG375 parts manual

SCHUNK

SCHUNK VERO-S NSE-A3 138 Assembly and operating manual

ABB

ABB HT566657 Operation manual

Webasto

Webasto GSE CAN installation guide