AUDAC SLM200 User manual
1. INTRODUCTION
With the SLM200 we developed a stable, safe and
reliable way to measure environmental noise levels.
This compact digital sound meter has been perfected
to achieve highly accurate measurements in a cost-
eective, tightly packed measuring instrument. We
envisioned a clever and ergonomic tool, accessible
when needed. That’s why the SLM200’s convenient
design is densely loaded with all the features of similar
bigger devices.
The SLM200 is an exceptionally versatile tool which is
convenient in a wide range of applications. Engineering,
product quality control and health monitoring are only
a handful of implementations where the SLM200 is
the appropriate tool. Applications are endless, the
SLM200 suits any environment where accurate noise
measuring is necessary.
2. WARNING
Before using this product, please read the operation
rules carefully. It includes relevant safety information
and warnings.
3. OPERATION SAFETY
This product strictly follows the requirements of
“General specication for sound level meters” in design
and production.
1. Please check the meter and the accessories before
using and beware of any damage. lf you nd the case
is damaged or the LCD shows nothing, or you consider
that the meter could not work properly anymore,
please stop using it.
2. Observe the operating instructions while measuring.
3. Do not open the meter at will or change internal
wiring, to avoid damages to the device.
4. When the LCD displays “ ”, replace the battery
timely. Remove the battery if the meter is not used
for a long time.
5. Do not store or use the meter in high temperature,
high humidity, ammable, combustible or strong
electromagnetic environments.
6. Please use a soft cloth and neutral detergent to
clean the case for maintenance. Do not use grinding
agent or solvent to avoid case corrosion and damage
to the meter.
5. DISPLAY INTERFACE
1. Maximum measurement 6. C weighted
2. Minimum measurement 7. Slow response rate
3. Data hold 8. Fast response rate
4. Low battery 9. Measurement value
5. A weighted
6. KEY FUNCTION AND SETUP
1. ON/OFF: Short press once to start up; short press
again to power o.
Note: Product’s auto power o feature can be disabled:
Press and hold “HOLD” and then press “ON/OFF” key to
enable/disable auto power o, the LCD will display
“APO OFF” to indicate the status.
2. FAST/SLOW: Sampling time: When measuring, pres-
sing this key to select between fast time of 125ms and
slow time of 1s.
USER MANUAL
MINI SOUND LEVEL METER
4. PRODUCT OVERVIEW
1. Windscreen 4. LCD Display
2. Microphone 5. Function keys
3. Meter Case
Windscreen
The WEEE marking indicates that this product
should not be disposed with regular household
waste at the end of its product life. This regulation
is created to protect both the environment and
human health.
This product is developed and manufactured with
high quality materials and components which can
be recycled and/or reused. Please dispose of this
product at your local collection point or recycling
center for electrical and electronic waste. Do this
to make sure that the product is recycled in an
environmental friendly way, and help to protect
the environment in which we all live.
This product contains no user serviceable parts.
Refer all servicing to qualied service personnel. Do
not perform any servicing (unless you are qualied
to do so).
CAUTION - SERVICING
This product conforms to all the essential
requirements and further relevant specications
described in following directives: 2014/30/EU (EMC)
and 2014/35/EU (LVD)
EC DECLARATION OF CONFORMITY
WASTE OF ELECTRICAL AND ELECTRONIC
EQUIPMENT (WEEE)
8. BATTERY INSTALLATION AND REPLACEMENT
This device uses 3 AAA 1.5 V batteries. Please
see the gure below for battery installation or
replacement.
The battery cover is located on the backpanel,
gently push it open in the direction of the arrow,
lift the cover and remove the batteries, install the
new batteries according to the polarity indications.
Close the cover by closing it and locking it back into
place.
USER MANUAL
MINI SOUND LEVEL METER
3. MAX/MIN: Press this key to select maximum,
minimum or normal measurement mode, when
maximum or minimum measurement is selected,
the meter constantly shows the maximum reading
or the minimum reading.
4. HOLD/BL:
HOLD: Short press this key once to hold the measu-
rement; short press the key once again to exit data
hold and continue normal measurement.
BL: long press this key to turn on backlight, and
long press it again to turn o backlight.
Sound level:
Response 31.5Hz - 8 kHz
Range 30 - 130 dB
Resolution 0.1 dB
Accuracy +/- 1.5 dB
Sampling time:
Fast 125 ms
Slow 1000 ms
Overload indication:
UN Under range
OL Over range
Auto Power O: 5 min
Low Battery Indicator: 3 - 3.5 V
LCD display: 4-Bit LCD display
(Max value: 9999)
Sensor type: 1/2” condenser microphone
Power requirements: 3 x 1.5 V batteries (AAA)
Product size: 150 x 52 x 27 mm
Weight: 116 g
7. TECHNICAL SPECIFICATIONS
Other AUDAC Measuring Instrument manuals
