Atmel STK512 User manual

5170C–AVR–10/09

STK512

....................................................................................................................

AVR-based Uni-directional

Radio Starter Kit Featuring

Secure Rolling-Code RF

Transmission Encryption

User Guide

Note: This Radio Starter Kit is not self-contained. It is based on an Atmel®AVR®STK®500

Flash Microcontroller Starter Kit that must be obtained separately.

STK512 User Guide i

5170C–AVR–10/09

Table of Contents

Section 1

Introduction.................................................................................................................1-1

1.1 Purpose.............................................................................................................................. 1-1

1.2 General Description ........................................................................................................... 1-1

1.3 Evaluation Kit Features......................................................................................................1-1

1.4 Included in the Kit .............................................................................................................. 1-2

Section 2

Getting Started ...........................................................................................................2-1

2.1 Hardware Assembly........................................................................................................... 2-1

2.2 Initial Programming............................................................................................................ 2-6

2.2.1 Programming the ATmega88 to Control the Receiver......................................... 2-6

2.2.2 Programming the Transmitter(s).......................................................................... 2-7

2.3 Teach the Transmitters to the Receiver............................................................................. 2-8

2.4 The Demonstration ............................................................................................................2-9

Section 3

Programming Notes ...................................................................................................3-1

3.1 Configuration...................................................................................................................... 3-1

3.2 Project Compilation............................................................................................................ 3-2

3.3 EEPROM Image Generation.............................................................................................. 3-2

Section 4

Troubleshooting Guide...............................................................................................4-1

STK512 User Guide 1-1

5170C–AVR–10/09

Section 1

Introduction

Congratulations on your purchase of the Atmel®AVR®-based Uni-directional Radio Starter Kit featuring

Secure Rolling Code RF Transmission Encryption. This kit uses an Atmel STK®500 Flash Microcon-

troller Starter Kit that must be obtained separately.

This User’s Guide describes how to use this Starter Kit. Section 2, Getting Started, describes how to

assemble and program the hardware to demonstrate a wireless link that uses a secure rolling code algo-

rithm. Section 3, Programming Notes, describes optional programming for the advanced user.

1.1 Purpose

This starter kit demonstrates a Secure Rolling Code Algorithm transmission protocol for use in a unidi-

rectional wireless communication system. Typical applications for this algorithm are garage door

openers, remote keyless entry, passive entry, and remote car-start systems.

1.2 General Description

This kit demonstrates the transmission protocol with one receiver and a pair of associated transmitters.

However, a typical system can support many more transmitters.

Characteristics of this protocol are:

A transmission-encryption value that is valid only once, preventing interception and re-transmission to

gain unauthorized access,

Message content that is virtually impossible to predict, even if previous messages are known.

For a thorough technical coverage of the hardware, software, and theory, read the application note,

“AVR411: Secure Rolling Code Algorithm for Wireless Link” that is included on the accompanying CD.

1.3 Evaluation Kit Features

Advanced Encryption Standard (AES) and its Cipher-based Message Authentication Code (CMAC)

mode of operation for transmitter authentication:

Multiple transmitters supported

PC command-line tools for cryptographic key management

Up to 256-bit key sizes supported

Less than 30 ms response time

315/434/868 MHz ISM-band frequencies

ATA5771/73/74 and ATA8741/42/43 UHF ASK/FSK transmitters with embedded ATtiny44

microcontroller

Introduction

1-2 STK512 User Guide

5170C–AVR–10/09

ATA5723/24/28 and ATA8203/04/05 UHF ASK/FSK receivers

User-programmable transmitters with 6-pin ISP

Sleep modes for minimal power consumption

1.4 Included in the Kit

Note: This Radio Starter Kit is not self-contained. It is based on an Atmel STK500 Flash Microcontroller Starter

Kit that must be obtained separately.

This starter kit includes all the essential components needed to demonstrate an AVR-based uni-direc-

tional radio that features a Secure Rolling-Code RF Transmission Encryption protocol. Contents of this

kit are listed and shown in Figure 1-1.

Transmitter application board

ISP programming adapter for Transmitter

Receiver application board with external antenna

STK512 Interface Board

ATMega88 microcontroller (not shown)

CDROM containing software, Data Sheets, and other documentation (not shown)

Introduction

STK512 User Guide 1-3

5170C–AVR–10/09

Figure 1-1. Kit Contents

For investigating further capabilities of this kit, the following are optional:

JTAGICE mkII for debugging

IAR Embedded Workbench®AVR C compiler for changing and recompiling the source code without

porting it to another compiler (precompiled source code with default configuration is provided on the

CDROM).

STK512 User Guide 2-1

5170C–AVR–10/09

Section 2

Getting Started

This section contains the steps required to get a simple system with a receiver and two transmitters up

and running. Hardware assembly, initial programming of the components, teaching the transmitters to

the receiver, and demonstrating the transmission protocol are described in the following subsections.

2.1 Hardware Assembly

The kit hardware must be interfaced to the STK500.

Step A: Assemble the STK500 Board

The STK500 Board must be set up properly before mounting the STK512 Interface Board. The assem-

bled STK500 Board is shown in Figure 2-1.

Figure 2-1. STK500 Board with Ribbon Cables and Microcontroller

Getting Started

2-2 STK512 User Guide

5170C–AVR–10/09

1. Carefully remove any ICs in the green “SCKT3200A2” socket.

2. Insert the furnished ATMega88 into the “SCKT3200A2” socket.

Note: The orientation of the red stripe in the cable is not critical in the following steps as long as pin 1 is con-

nected to pin 1.

3. Using a 6-pin jumper cable supplied with the STK500;

connect the two male headers “ISP6PIN” and “SPROG2”.

4. Using a 10-pin jumper cable supplied with the STK500;

connect the two male headers “PORTC” and “LEDS”.

5. Using a 10-pin jumper cable supplied with the STK500;

connect the two male headers “PORTD” and “SWITCHES”.

6. Place jumpers on the following headers as shown in Figure 2-2.

–VTARGET

–AREF

– RESET

–XTAL1

– OSCEL (a 3-pin header. Place a jumper next to the “1” printed on the board).

Figure 2-2. Detail of Jumper Placement on the STK500

Getting Started

STK512 User Guide 2-3

5170C–AVR–10/09

Step B: Assemble and Attach the STK512 Interface Board

The STK512 Interface Board must be assembled and mounted on the STK500 Board. The completed

assembly is shown in Figure 2-3.

Figure 2-3. Assembled STK512 Interface Board

1. Orient the STK500 as shown in the Figure 2-3.

Caution: After the next step, whenever the interface board is removed from the STK500 sockets, use

caution if a tool is used for leverage. It is easy to bend pins or otherwise damage the STK500 and/or the

interface board. Use a rocking motion while steadily pulling (not prying) it straight from the sockets.

2. Insert the STK512 Interface Board into the EXPANDx sockets, oriented with the LEDs and red DIP

switches to the left-hand side. To verify the orientation, check that the EXPAND0 pins on the Inter-

face Board plug into the EXPAND0 socket on the STK500 Board. Press firmly so that the board pins

seat well.

3. Install jumpers on all five pairs of pins (JP2, next to the “configure” button) as shown in Figure 2-4.

Getting Started

2-4 STK512 User Guide

5170C–AVR–10/09

Figure 2-4. STK512 Jumper Placement

Getting Started

STK512 User Guide 2-5

5170C–AVR–10/09

Step C: Mount the Receiver Application Board

The Receiver Application Board must be mounted on the STK512 Interface Board. The completed

assembly is shown in Figure 2-5.

Figure 2-5. Completed Receiver Assembly

Caution: After the next step, if the receiver board is removed from the interface board sockets, use

EXTREME caution! The pins on the receiver board are very easily bent and broken! Use a rocking

motion to lift the board straight (perpendicular) out of the socket.

1. Orient the receiver board above the Interface Board as shown in Figure 2-5. Carefully insert the

Receiver Application Board into the STK512 Interface Board sockets.

2. Install the antenna onto the SMB connector.

3. Supply the STK500 with +12 V power by connecting it to a PC using the RS232 port.

Table of contents

Other Atmel Microcontroller manuals

Atmel

Atmel AVR32918 User manual

Atmel

Atmel AVR STK100 User manual

Atmel

Atmel AT91SAM9 Installation and operating instructions

Atmel

Atmel AVR 1908 User manual

Atmel

Atmel AT91 Series User manual

Atmel

Atmel AVR AT90S4434 User manual

Atmel

Atmel ATtiny104 Xplained Nano User manual

Atmel

Atmel AVR8015 Installation and operating instructions

Atmel

Atmel AT43DK355 User manual

Atmel

Atmel AVR365 User manual

Atmel

Atmel UC3-L0 Xplained Installation and operating instructions

Atmel

Atmel AVR AT90S2333 User manual

Atmel

Atmel ATmega161 User manual

Atmel

Atmel 80C51 Installation and operating instructions

Atmel

Atmel AT88CK109STK3 Installation manual

Atmel

Atmel AT89C51 User guide

Atmel

Atmel ATF15 DK3-U Series User manual

Atmel

Atmel AVR1306 User manual

Atmel

Atmel AVR180 Installation and operating instructions

Atmel

Atmel XMEGA A3 series User manual

Atmel

Atmel QTouch Installation and operating instructions

Atmel

Atmel AT91 Series User manual

Atmel

Atmel AT90S2313 User manual

Atmel

Atmel ATmega8 User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide