Apera Instruments 2310T-F User manual

2310T-F High-Range Conductivity/Temp. Electrode

User Manual

Brief Introduction

Apera Instruments 2310T-F High-Range Conductivity/Temp. Electrode is featured with a proprietary

platinum black ring sensor for accurate readings in an ultra-wide conductivity range up to 2000 mS/cm,

along with a built-in temperature sensor for automatic temperature compensation.

Technical Specifications

Range

20 to 2000 mS/cm, 32 to 122°F (0 to

50°C)

Housing

POM

Constant

K=10

Connector

BNC/RCA

Cable length

3 Ft

Dimension

ø12*145 mm

Temperature sensor

30KΩ thermistor

Operating temperature

32 to 176°F (0 - 80°C)

How to Install the Electrode

1. Find the conductivity BNC socket (where it shows Cond) on the conductivity meter; Open the

rubber cap; Insert the BNC connector of the electrode to the BNC socket while twisting clockwise

until it’s locked.

2. Find the RCA socket (where it shows temp) on the meter; Open the rubber cap; Insert the black

RCA connector of the electrode to the RCA socket directly.

3. After connecting the new electrode to your meter, adjust the meter’s constant K to 10 according to

the instruction of your meter’s manual. Then perform a 2 to 3-point calibration to ensure the

accuracy.

How to Use the Electrode

1. There is a proper amount of deionized water in the cap on top of the electrode. The conductivity

sensor is soaked in it to keep its sensitivity.

2. Before measuring, loosen the bottle cap, then pull out the electrode while twisting

counterclockwise. Place the storage bottle at a safe position.

3. Rinse the electrode with distilled or deionized water and blot-dry it with clean tissue or filter paper.

Never rub the sensor. Rinse the electrode again with your test solution if possible for the best result.

4. Insert the electrode into your sample solution and stir it for a few seconds in the solution to remove

potential air bubbles. Then wait for the stable reading and take the measurement.

5. After measurement, insert the electrode back into the storage cap and twist it on. If the water in

the cap is contaminated, rinse out the storage cap and fill in new deionized or distilled water.

How to Maintain the Electrode

1. Always rinse the electrode with distilled or deionized water before and after each test and

calibration.

2. Store the electrode in the storage cap filled with distilled or deionized water when not in use.

3. Keep the electrode’s connector clean and dry. Use cotton balls with isopropyl alcohol to clean if

it gets dirty and then blow-dry it. This is to prevent a potential short circuit, which will

undermine the electrode’s performance.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agree to repair or

replace free of charge, at the option of APERA INSTRUMENTS, LLC, any malfunctioned or damaged

product attributable to responsibility of APERA INSTRUMENTS, LLC for a period of SIX MONTHS

from the delivery.

This warranty does not cover any damages due to:

Accidental damage, transportation, storage, improper use, failure to follow the product instructions,

unauthorized repair, normal wear and tear, or any other actions or events beyond our reasonable control.

APERA INSTRUMENTS, LLC

Address: 6656 Busch Blvd, Columbus, OH 43229 Phone: +1 (614) 285-3080

Website: aperainst.com Email: info@aperainst.com

Table of contents

Other Apera Instruments Measuring Instrument manuals

Apera Instruments

Apera Instruments DO803 User manual

Apera Instruments

Apera Instruments PH60 User manual

Apera Instruments

Apera Instruments TN420 User manual

Apera Instruments

Apera Instruments PH60-WW User manual

Apera Instruments

Apera Instruments TN500 User manual

Apera Instruments

Apera Instruments YD300 User manual

Apera Instruments

Apera Instruments YD300 User manual

Apera Instruments

Apera Instruments EC700 User manual

Apera Instruments

Apera Instruments PH60Z-MS User manual

Apera Instruments

Apera Instruments 2301T-S User manual

Apera Instruments

Apera Instruments LabSen 221 User manual

Apera Instruments

Apera Instruments LabSen 851-H User manual

Apera Instruments

Apera Instruments SX811-SS User manual

Apera Instruments

Apera Instruments LabSen 551 User manual

Apera Instruments

Apera Instruments PH910 User manual

Apera Instruments

Apera Instruments GroStar AI101G User manual

Apera Instruments

Apera Instruments Gro Star AI104G User manual

Apera Instruments

Apera Instruments SX811-BS User manual

Apera Instruments

Apera Instruments 2401T-F User manual

Apera Instruments

Apera Instruments LabSen 821 User manual

Apera Instruments

Apera Instruments PH850 User manual

Apera Instruments

Apera Instruments SX751 User manual

Apera Instruments

Apera Instruments Premium Series User manual

Apera Instruments

Apera Instruments WS100 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual