Anga AQ-7103VSW User manual
Yoosee fast operating guide V1.3
Version explanation:
20170324:V1.3 Simplify & normalize operating process.
I. Learn about your camera
1. Ethernet port 2.TF card port 3.power port
1:network light；
2：
alarm light；
3：
video light；
：
deploying alarm light; 5：
infrared receipt
You can c eck w et er camera works properly or not by watc ing below indicator lig t:
indicator light always on twinkle Off
network lig t connected properly connecting no connection
alarm lig t alarming
no alarm
recording lig t wit TF card recording no TF card
deploying alarm lig t deployed alarm
deploying alarm no deploying alarm
II. Download & install Yoosee APP for phone
Go to Apple APP Store or Android Google Play and searc for Yoosee or you can go to
www.yoosee.co to download & install Yoosee t en finis registration according to t e
instructions and log in.
III. Add camera
1. Register & log in
App can be registered via p one numbers and e-mail addresses as well as via WeC at.
Note: p one numbers registration is only limited in C ina currently and also do use true e-mail
addresses better for finding forgotten password back in t e future.
2. Process of adding new devices
Device needs to be back to initialized status by pressing t e “reset” button for 5 seconds w en
adding new devices.
Two ways for adding device: one is via WiFi, t e ot er is via wire. WiFi adding can be divided into
smart link and AP connection.
Met od 1: adding via WiFi (recommend indoor using),put p one WiFi to connect wit wireless
router( make sure connected WiFi is 2.4G WiFi as camera is not supported for 5G WiFi)
open
Yoosee App
click”+”on t e rig t upper corner of device listing
select smart link or AP
connection.
Smart link (it might to be failed when adding via this way due to the restriction of certain
routers, if fails, you can try to connect with AP connection)
Select smart link
follow up wit t e instructions
connected WiFi successfully
input
device default password (if no, you can create a new password according to instructions)
save & add successfully.
AP connection
Select AP connection
input t e WiFi password asked by device
create visiting password
click “next step”
enter into interface of “adding device”
select your wanted device
GW-AP-XXX
follow up wit t e instructions.
Met od 2: wired adding (recommend outdoor use)
Select wired connection
select wanted device in new device listings
create device name &
password
save.
IV. Introduction of function buttons
Weak password icon: suggest to revise password w en t is icon is on.
Defense succeeded & disarming succeeded : deploy must be switc on w en using alarm
notification and alarm recording.
Video playback
Setting
①③②④
Remote recording: record videos and save it to p one.
Remote capturing: capture video screens ot and save it to p one.
Intercom system: press t e button and you can talk remotely.
Defense succeeded & disarming succeeded
Memory point settings (it needs firmware support)
You can adjust t e monitoring direction wit your finger sliding t e screen up and down.
①② ③ ④ ⑤
⑥
⑥
V. Settings
Device information：firmware version. We need to know firmware information w en
somet ing appens to firmware.
Time settings： set device’s time and time zone.
Picture and sound：set device video format
volume
video quality
motion detection
sensitivity
reverse image
indicator lig t and so on.
Security settings：set or revise device administer password and visitor password w ic is just
for monitoring t e device and doesn’t ave any ot er operating rig ts.
Defense settings (t is function needs device support)：
set regular plan of deploying & revoking
alarm
Network settings：s ift between wired & WiFi connection or s ift to ot er WiFi.
Alarm settings：receive alarm prompt
delete alarm pus ing account
bound alarm pus ing
e-mail
buzzer
motion detection and sensitivity.
Record settings：set record mode---record manually, record alarm, record timer.
Note: motion detection or sensor s ould be switc ed on as well as defense succeeded w en
using alarm notification and alarm recording.
Add sensor (t is function needs device support)：it’s available to add ordinary sensor (door
magnetic, PIR), remoter, special sensor (smoke detector, special gas detector).
Adding met ods :click”+” in add sensor interface
confirm
trigger sensor
add successfully.
Using case: switc on “receive alarm prompt” in alarm settings after add sensor successfully. And
at t e same time deploying alarm s ould be done. Once door magnetic is triggered after
deploying alarm successfully, device will send alarm notifications to p one APP.
Firmware update：update & optimize device firmware.
Change to standalone mode (t is function needs device support)
it applies to t e users
wit out using router. You can get t roug via AP ot WiFi under t is mode.
Users wit out router can access t roug device
s ot WiFi, details are as follows:
Let device back to t e initialized status
connect device ’s ot WiFi: GW-AP-XXX
back to APP
interface of “configuring camera” and click “skip, s ift to AP mode”
confirm
find t e device
Table of contents
