AJAX DoubleButton User manual

DoubleButton User Manual

Updated October 20, 2020

DoubleButton is a wireless hold-up device with advanced protection against

accidental presses. The device communicates with a hub via the encrypted

radio protocol and compatible only with Ajax security systems. The

line-of-sight communication range is up to 1300 meters. DoubleButton operates

from the pre-installed battery up to 5 years.

DoubleButton is connected and congured via on iOS, Android,

macOS, and Windows. Push notications, SMS, and calls can notify about

alarms and events.

Buy the DoubleButton hold-up device

Functional elements

Jeweller

Ajax apps

Operating principle

DoubleButton is a wireless hold-up device, featuring two tight buttons and a

plastic divider to protect against accidental presses. When pressed, it raises an

alarm (hold-up event), transmitted to users and to the security company’s

monitoring station.

An alarm can be raised by pressing both buttons: one-time short or long press

(more than 2 seconds). If only one of the buttons is pressed, the alarm signal is

not transmitted.

All DoubleButton alarms are recorded in the feed. The

short and long presses have different icons, but the event code sent to the

monitoring station, SMS, and push notications do not depend on the pressing

manner.

DoubleButton can only operate as a hold-up device. Setting the type of alarm is

not supported. Keep in mind that the device is active 24/7, so pressing the

DoubleButton will raise an alarm regardless of the security mode.

Only are available for DoubleButton. The control mode for

is not supported.

Ajax app’s notication

alarm scenarios automation

devices

Event transmission to the monitoring station

The Ajax security system can connect to the CMS and transmit alarms to the

monitoring station in and protocol formats.

Connection

The device is not compatible with , , and third party security

control panels.

Before starting connection

Only users with administrator permissions can connect a device to a hub.

How to connect DoubleButton to a hub

Sur-Gard (ContactID) SIA DC-09

ocBridge Plus uartBridge

1. Install the . Create an . Add a hub to the app and create at

least one room.

Ajax app account

2. Check if your hub is on and connected to the Internet (via Ethernet cable, Wi-

Fi, and/or mobile network). You can do this in the Ajax app or by looking at

the Ajax logo on the front panel of the hub. The logo should light with white

or green if the hub is connected to the network.

3. Check if the hub is not armed and does not update by reviewing its status in

the app.

1. Open the Ajax app. If your account has access to several hubs, select the

hub to which you want to connect the device.

2. Go to the Devices tab and click Add device.

3. Name the device, scan or enter the QR code (located on the package), select

a room and a group (if group mode is enabled).

4. Click Add— the countdown will begin.

To connect DoubleButton to a hub, it should be located on the same protected object as

the system (within the hub’s radio network range). If the connection fails, try again in 5

seconds.

DoubleButton can be connected to one hub only. When connected to a new hub,

the device stops sending commands to the old hub. Added to a new hub,

DoubleButton is not removed from the device list of the old hub. This must be

done manually in the Ajax app.

Updating the device statuses in the list occurs only when DoubleButton is pressed and

does not depend on the Jeweller settings.

States

The states screen contains information about the device and its current

parameters. Find the DoubleButton states in the Ajax app:

Parameter Value

Battery charge

Battery charge level. Two states are indicated:

LED brightness Indicates the LED brightness level:

5. Hold any of two buttons for 7 seconds. After adding DoubleButton, its LED

will ash green once. DoubleButton will appear in the list of hub devices in

the app.

1. Go to the Devices tab .

2. Select DoubleButton from the list.

• ОК

• Battery low

• Off — no indication

• Low

Works via *range extender name*

Indicates the status of the ReX range extender

use.

The eld is not displayed if the device

communicates directly with a hub

Temporary Deactivation

Indicates the status of the device:

Firmware DoubleButton rmware version

ID Device ID

Setting up

DoubleButton is set up in the Ajax app:

Please note that after changing the settings, you need to press Back to apply them.

Parameter Value

First eld

Device name. Displayed in the list of all hub

devices, SMS, and notications in the event

feed.

The name can contain up to 12 Cyrillic

characters or up to 24 Latin characters

• Max

• Active

• Temporarily deactivated

Learn more

1. Go to the Devices tab .

2. Select DoubleButton from the list.

3. Go to Settings by clicking on the icon.

Room Selecting the virtual room to which

DoubleButton is assigned. The name of the

room is displayed in SMS and notications in

the event feed

LED brightness

Adjusting LED brightness:

Alert with a siren if button is pressed

When enabled, the connected to your

security system signal about the button

pressing

User Manual Opens the DoubleButton user manual

Temporary Deactivation

Allows the user to disable the device without

removing it from the system. A temporarily

deactivated device will not raise an alarm when

pressed

Unpair device Disconnects DoubleButton from a hub and

removes its settings

Alarms

A DoubleButton alarm generates an event notication sent to the security

company’s monitoring station and system users. The pressing maner is

indicated in the event feed of the app: for a short press, a single-arrow icon

appears, and for a long press, the icon has two arrows.

• Off — no indication

• Low

• High

sirens

Learn more about temporary

deactivation of devices

To reduce the probability of false alarms, a security company can enable the

feature.

Note that the alarm conrmation is a separate event that does not cancel the

alarm transmission. Whether or not the feature is enabled, DoubleButton alarms

are sent to a CMS and to security system users.

Indication

DoubleButton blinks red and green to indicate command execution and battery

charge status.

Category Indication Event

Pairing with a security system

The whole frame blinks green

6 times

The button is not connected to

a security system

The whole frame lights up

green for a few seconds

Connecting the device to a

security system

Command delivery indication The frame part above the

pressed button lights up green

briey

One of the buttons is pressed

and the command is delivered

to a hub.

alarm conrmation

When only one button is

pressed, DoubleButton does

not raise an alarm

The entire frame lights up

green briey after press

Both buttons are pressed and

the command is delivered to a

hub

The entire frame lights up red

briey after press

One or both buttons were

pressed and the command

was not delivered to a hub

Response Indication

(follows the Command

Delivery Indication)

The whole frame lights up

green for half a second after

the command delivery

indication

A hub received DoubleButton

command and raised an alarm

The whole frame lights up red

for half a second after the

command delivery indication

A hub received DoubleButton

command but did not raise an

alarm

Battery status indication

(follows Feedback Indication)

After the main indication, the

entire frame lights up red and

gradually goes out

The battery replacement is

required. DoubleButton

commands are delivered to a

hub

Application

DoubleButton can be xed on a surface or carried around.

How to x DoubleButton on a surface

To x the device on a surface (e. g. under a table), use Holder.

To install the device in the holder:

1. Choose a location to install the holder.

2. Press the button to test whether the commands are delivered to a hub. If

not, choose another location or use the .

When routing DoubleButton through ReX, keep in mind that it does not

automatically switch between a range extender and a hub. You can assign

DoubleButton to a hub or another ReX in the Ajax app.

ReX radio signal range extender

3. Fix Holder on the surface using the bundled screws or double-sided

adhesive tape.

4. Put DoubleButton into the holder.

Please note that Holder is sold separately.

Buy Holder

How to carry DoubleButton

The button is easy to carry around thanks to a special hole on its body. It can be

worn on the wrist or neck, or be hanged on a keyring.

DoubleButton has an IP55 protection index. Which means that the device body

is protected from dust and splashes. And a special protective divider, tight

buttons, and the need to press two buttons at once eliminate false alarms.

Using DoubleButton with alarm conrmation enabled

Alarm conrmation is a separate event that a hub generates and transmits to a

CMS if the hold-up device has been activated by different types of pressing

(short and long) or two specied DoubleButtons have transmitted alarms within

Other manuals for DoubleButton

Table of contents

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual

DSC

DSC PC 4010 Programming manual