AJAX DoubleButton User manual
DoubleButton User Manual
Updated November 14, 2020
DoubleButton is a wireless hold-up device with advanced protection against
accidental presses. The device communicates with a hub via the encrypted
radio protocol and compatible only with Ajax security systems. The line-
of-sight communication range is up to 1300 meters. DoubleButton operates from
the pre-installed battery up to 5 years.
DoubleButton is connected and congured via on iOS, Android, macOS,
and Windows. Push notications, SMS, and calls can notify about alarms and
events.
Functional elements
Jeweller
Ajax apps
Buy the DoubleButton hold-up device
Operating principle
DoubleButton is a wireless hold-up device, featuring two tight buttons and a plastic
divider to protect against accidental presses. When pressed, it raises an alarm
(hold-up event), transmitted to users and to the security company’s monitoring
station.
An alarm can be raised by pressing both buttons: one-time short or long press
(more than 2 seconds). If only one of the buttons is pressed, the alarm signal is not
transmitted.
1. Alarm activation buttons
2. LED indicators / plastic protective divider
3. Mounting hole
All DoubleButton alarms are recorded in the feed. The short
and long presses have different icons, but the event code sent to the monitoring
station, SMS, and push notications do not depend on the pressing manner.
DoubleButton can only operate as a hold-up device. Setting the type of alarm is not
supported. Keep in mind that the device is active 24/7, so pressing the
DoubleButton will raise an alarm regardless of the security mode.
Only are available for DoubleButton. The control mode for
is not supported.
Event transmission to the monitoring station
The Ajax security system can connect to the CMS and transmit alarms to the
monitoring station in and protocol formats.
Connection
The device is not compatible with , , and third party security control
panels.
Ajax app’s notication
alarm scenarios automation
devices
Sur-Gard (ContactID) SIA DC-09
ocBridge Plus uartBridge
Before starting connection
Only users with administrator permissions can connect a device to a hub.
How to connect DoubleButton to a hub
To connect DoubleButton to a hub, it should be located on the same protected object as the
system (within the hub’s radio network range). If the connection fails, try again in 5 seconds.
DoubleButton can be connected to one hub only. When connected to a new hub,
the device stops sending commands to the old hub. Added to a new hub,
1. Install the . Create an . Add a hub to the app and create at
least one room.
Ajax app account
2. Check if your hub is on and connected to the Internet (via Ethernet cable, Wi-Fi,
and/or mobile network). You can do this in the Ajax app or by looking at the
Ajax logo on the front panel of the hub. The logo should light with white or
green if the hub is connected to the network.
3. Check if the hub is not armed and does not update by reviewing its status in
the app.
1. Open the Ajax app. If your account has access to several hubs, select the hub
to which you want to connect the device.
2. Go to the Devices tab and click Add device.
3. Name the device, scan or enter the QR code (located on the package), select a
room and a group (if group mode is enabled).
4. Click Add— the countdown will begin.
5. Hold any of two buttons for 7 seconds. After adding DoubleButton, its LED will
ash green once. DoubleButton will appear in the list of hub devices in the app.
DoubleButton is not removed from the device list of the old hub. This must be done
manually in the Ajax app.
Updating the device statuses in the list occurs only when DoubleButton is pressed and does
not depend on the Jeweller settings.
States
The states screen contains information about the device and its current
parameters. Find the DoubleButton states in the Ajax app:
Parameter Value
Battery charge
Battery charge level. Two states are indicated:
LED brightness
Indicates the LED brightness level:
Works via *range extender name*
Indicates the status of the ReX range extender
use.
The eld is not displayed if the device
communicates directly with a hub
Temporary Deactivation Indicates the status of the device:
1. Go to the Devices tab .
2. Select DoubleButton from the list.
ОК
Battery low
Off — no indication
Low
Max
Active
Firmware DoubleButton rmware version
ID Device ID
Setting up
DoubleButton is set up in the Ajax app:
Please note that after changing the settings, you need to press Back to apply them.
Parameter Value
First eld
Device name. Displayed in the list of all hub
devices, SMS, and notications in the event feed.
The name can contain up to 12 Cyrillic characters
or up to 24 Latin characters
Room
Selecting the virtual room to which DoubleButton
is assigned. The name of the room is displayed in
SMS and notications in the event feed
LED brightness Adjusting LED brightness:
Temporarily deactivated
Learn more
1. Go to the Devices tab .
2. Select DoubleButton from the list.
3. Go to Settings by clicking on the icon.
Off — no indication
Low
High
Alert with a siren if button is pressed When enabled, the connected to your
security system signal about the button pressing
User Manual Opens the DoubleButton user manual
Temporary Deactivation
Allows the user to disable the device without
removing it from the system. A temporarily
deactivated device will not raise an alarm when
pressed
Unpair device Disconnects DoubleButton from a hub and
removes its settings
Alarms
A DoubleButton alarm generates an event notication sent to the security
company’s monitoring station and system users. The pressing maner is indicated
in the event feed of the app: for a short press, a single-arrow icon appears, and for
a long press, the icon has two arrows.
To reduce the probability of false alarms, a security company can enable the
feature.
sirens
Learn more about temporary
deactivation of devices
alarm
conrmation
Note that the alarm conrmation is a separate event that does not cancel the alarm
transmission. Whether or not the feature is enabled, DoubleButton alarms are sent
to a CMS and to security system users.
Indication
DoubleButton blinks red and green to indicate command execution and battery
charge status.
Category Indication Event
Pairing with a security system
The whole frame blinks green 6
times
The button is not connected to
a security system
The whole frame lights up
green for a few seconds
Connecting the device to a
security system
Command delivery indication
The frame part above the
pressed button lights up green
briey
One of the buttons is pressed
and the command is delivered
to a hub.
When only one button is
pressed, DoubleButton does
not raise an alarm
The entire frame lights up green
briey after press
Both buttons are pressed and
the command is delivered to a
hub
The entire frame lights up red
briey after press
One or both buttons were
pressed and the command was
not delivered to a hub
Response Indication
(follows the Command Delivery
Indication)
The whole frame lights up
green for half a second after
the command delivery
indication
A hub received DoubleButton
command and raised an alarm
The whole frame lights up red
for half a second after the
command delivery indication
A hub received DoubleButton
command but did not raise an
alarm
Battery status indication
(follows Feedback Indication)
After the main indication, the
entire frame lights up red and
gradually goes out
The battery replacement is
required. DoubleButton
commands are delivered to a
hub
Application
DoubleButton can be xed on a surface or carried around.
How to x DoubleButton on a surface
To x the device on a surface (e. g. under a table), use Holder.
To install the device in the holder:
1. Choose a location to install the holder.
2. Press the button to test whether the commands are delivered to a hub. If not,
choose another location or use the .
When routing DoubleButton through ReX, keep in mind that it does not automatically
switch between a range extender and a hub. You can assign DoubleButton to a hub or
another ReX in the Ajax app.
ReX radio signal range extender
3. Fix Holder on the surface using the bundled screws or double-sided adhesive
tape.
4. Put DoubleButton into the holder.
Other manuals for DoubleButton
3
This manual suits for next models
2
Table of contents
Other AJAX Security System manuals
AJAX
AJAX StreetSiren User manual
AJAX
AJAX HomeSiren User manual
AJAX
AJAX Hub 2 Plus User manual
AJAX
AJAX Hub 2 Plus User manual
AJAX
AJAX Hub Hybrid User manual
AJAX
AJAX Hub 2 Plus User manual
AJAX
AJAX StreetSiren User manual
AJAX
AJAX vhfBridge User manual
AJAX
AJAX HomeSiren User manual
AJAX
AJAX Tag User manual
AJAX
AJAX StreetSiren User manual
AJAX
AJAX KeyPad User manual
AJAX
AJAX Button User manual
AJAX
AJAX StreetSiren User manual
AJAX
AJAX StreetSiren DoubleDeck User manual
AJAX
AJAX StreetSiren User manual
AJAX
AJAX StreetSiren User manual
AJAX
AJAX ManualCallPoint Jeweller User manual
AJAX
AJAX HomeSiren User manual
AJAX
AJAX StreetSiren User manual
