Siemens FDM273 User manual
FDM273
Radio manual call point
Mounting
A6V10347888_h_en_-- Smart Infrastructure
2020-03-31
Imprint
Technical specifications and availability subject to change without notice.
Transmittal, reproduction, dissemination and/or editing of this document as well as
utilization of its contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable for payment of damages.
All rights created by patent grant or registration of a utility model or design patent
are reserved.
Issued by:
Siemens Switzerland Ltd.
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. +41 58 724-2424
www.siemens.com/buildingtechnologies
Edition: 2020-03-31
Document ID: A6V10347888_h_en_--
© Siemens Switzerland Ltd, 2013
Imprint
2 | 18 A6V10347888_h_en_--
A6V10347888_h_en_-- 3 | 18
Table of contents
1 About this document................................................................................. 5
2 Mounting and installation.......................................................................... 6
2.1 Preparation ............................................................................................... 6
2.2 Installing the housing................................................................................ 7
2.3 Installation ................................................................................................ 8
2.4 Installing the protective cover ................................................................... 11
2.5 Inserting the door sign .............................................................................. 12
3 Details for ordering ................................................................................... 13
3.1 Switching unit FDME273 .......................................................................... 13
3.2 Housing FDMH273-R ............................................................................... 13
3.3 Battery pack BAT3.6-10 ........................................................................... 13
3.4 KeyDMZ1195........................................................................................... 14
3.5 Glass insert DMZ1196-AC........................................................................ 14
3.6 Protective cover DMZ1197-AC................................................................. 14
3.7 Door sign .................................................................................................. 14
4 Specifications ........................................................................................... 15
4.1 Technical data .......................................................................................... 15
4.2 Dimensions............................................................................................... 16
4.3 Master gauge for recesses ....................................................................... 17
4.4 Environmental compatibility and disposal................................................. 17
4 | 18 A6V10347888_h_en_--
1 About this document
Overview
The FDM273 radio manual call point is intended for use in areas of a house where
a fire can be detected by people who can manually trigger an alarm.
The FDM273 radio manual call point consists of a housing, a switching unit, and a
battery pack.
Goal and purpose
This document contains all the information required to install the FDM273 manual
call point.
Prerequisites:
● The installation location of the radio manual call point has been established.
● Mounting should be performed by a specialist in compliance with safety
regulations.
You will find more information on the FDM273 radio manual call point in document
A6V10347733.
Applicable documents
Document ID Title
A6V10271323 Data sheet SWING Neural radio fire detector FDCW241,
FDOOT271, FDM273, FDM275, FDM275(F)
A6V10227631 Planning Radio fire detection system SWING
A6V10347733 Technical Manual Radio manual call point FDM273
Intended use
The radio manual call pointFDM273 may only be used together with a radio
gatewayFDCW241 in a fire detection system FS20/FS720.
About this document 1
A6V10347888_h_en_-- 5 | 18
2 Mounting and installation
2.1 Preparation
Secure the housing at a height of 0.9…1.6m on an even surface. Observe the
country-specific regulations for the exact mounting height!
3
180°
2
3
1
3
Figure 1: Opening the housing and identifying the screw holes
1 Screw opening 3 Break-out points
2 Door sign
wThe position of the radio manual call point has been established.
wYou have the housing, switching unit, and battery pack to hand.
wYou have a tool and two screws for securing purposes. The screws have a
Ø2.5…3mm shaft and a Ø>8mm head surface.
1. Push the keyhole cover to the right.
2. Open the door with the key supplied.
3. NOTICE!Keep the key in a safe place.
4. Push the keyhole cover back into place.
5. For securing purposes, select two screw positions that are spaced far apart
from one another. Use screw position(1) if possible. There are additional
securing points in the back box.
– Working from the rear of the housing, break out an appropriate screw hole
at one of the marked break-out points(3) in the back box.
6. Replace the window sign(2) if necessary.
aThe housing is now ready for installation.
Mounting and installation
Preparation
2
6 | 18 A6V10347888_h_en_--
2.2 Installing the housing
>8 mm
2,5...3 mm
Figure 2: Example of securing onto the substructure using two screws
wThe housing is ready for mounting. See the chapter 'Preparation'.
lScrew the housing securely onto the substructure using two screws.
aThe housing has been installed.
Mounting and installation
Installing the housing 2
A6V10347888_h_en_-- 7 | 18
2.3 Installation
1
1
3
2
4
5
6
2
3
7
7
8
9
10
1 Screws 6 Battery pack BAT3.6-10 1
2 Switching unit FDME273 7 Holders
3 Battery connector 8 Locking lever
4 Housing FDMH273-R 9 Internal alarm indicator
5 Door 10 Alarm button
1Not included in the scope of delivery
The flashing behavior of the internal alarm indicator is described in document
A6V10347733 in the 'Internal alarm indicator' chapter.
wThe housing has been installed.
wThe radio gateway has been activated and switched to maintenance mode.
wThe battery pack and switching unit are available.
wThe switching unit is set to the factory settings.
wThe door(5) is open.
wThe alarm button(10) on the switching unit(2) has not been pressed and is
protruding by about 5mm.
1. If the alarm button has been pressed, push the black locking lever(8) in the
direction of the arrow until it clicks.
aThe alarm button is now protruding by approx. 5mm.
Mounting and installation
Installation
2
8 | 18 A6V10347888_h_en_--
2. Remove the adhesive label with the serial number from the type plate on the
switching unit. Use the adhesive label to mark the position of the radio manual
call point FDM273 on the device location plan.
3. Turn over the window sign if necessary, or use a different one.
4. Label the battery pack(6) with the current date.
5. Lay the connection cable and connect the battery connector(3).
aWhen the battery connector is connected, the internal alarm indicator(9)
lights up red for five seconds.
aAfter a further 10 seconds, the radio manual call point signals that it is not
mounted in the housing, and the internal alarm indicator flashes every two
seconds:
– If it flashes red, this indicates the factory settings.
– If it flashes green, this indicates that the radio manual call point has already
been logged on to a radio gateway.
aIf this does not happen, this means the battery pack is defective and must
not be used.
6. Insert the battery pack into the switching unit FDME273 so that it snaps into
place in the holders(7).
7. Insert the switching unit with the battery pack into the housing, paying attention
to the position of the battery cable.
8. Connect the switching unit securely to the housing using two screws(1).
aThe internal alarm indicator flashes green and the radio manual call point is
logged on to the radio gateway.
aIf the process of logging on to the radio gateway is successful, the internal
alarm indicator stops flashing.
9. If the logon process has not been successful after a long period of time, briefly
remove the switching unit from the housing and then re-insert it.
aThe search for the radio network starts again.
10. Close the door.
aThe radio manual call point is now mounted and is ready for commissioning.
WARNING
Deactivated manual call points prevent alarms from being transmitted.
The alarm is not triggered.
● Mark deactivated manual call points or those which are not fully functional
with the notice 'NOT IN USE'!
Mounting and installation
Installation 2
A6V10347888_h_en_-- 9 | 18
OUT OF ORDER
AUSSER BETRIEB
HORS SERVICE
FUORI SERVIZIO
FUERA DE SERVICIO
BUITEN GEBRUIK
Figure 3: 'NOT IN USE' label
Mounting and installation
Installation
2
10 | 18 A6V10347888_h_en_--
Table of contents
Other Siemens Security System manuals
Siemens
Siemens FS-RD2 User manual
Siemens
Siemens FDM273-O Guide
Siemens
Siemens SIRIUS 8WD42 User manual
Siemens
Siemens FDM223-Ex User manual
Siemens
Siemens SIRIUS 8WD4420-0EA User manual
Siemens
Siemens MM8000 Quick setup guide
Siemens
Siemens FDS181C User manual
Siemens
Siemens Cerberus PACE User manual
Siemens
Siemens FDM221 User manual
Siemens
Siemens FS20 Operating instructions
Siemens
Siemens IC60 User manual
Siemens
Siemens FDM275 User manual
Siemens
Siemens FDM225 User manual
Siemens
Siemens SIPASS SK5 Installation and operation manual
Siemens
Siemens TZC-8B User manual
Siemens
Siemens FDS221-W User manual
Siemens
Siemens SIMATRIX NEO 2GF2211-8EA Instruction manual
Siemens
Siemens FDM275 Guide
Siemens
Siemens IC60 User manual
Siemens
Siemens HMS-S User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
DSC
DSC PC 4010 Programming manual