Agilent Technologies LogicWave User manual

Agilent Technologies

LogicWave

Installation Guide

Publication number E9340-97002

December 2000

For Safety information, Warranties, and Regulatory information,

see the pages behind the index.

In This Book

This book:

• Shows how to install and care for the LogicWave logic analyzer.

• Describes the LogicWave specifications and characteristics.

See Also The online help for information on using LogicWave.

Contents

In This Book

1 Setting Up LogicWave

Installing LogicWave 6

Step 1. Connect the logic analyzer to a host computer (PC) 7

Step 2. Connect the power cable 8

Step 3. Turn on power 9

Step 4. Install software 10

Step 5. Start the LogicWave user interface 11

Step 6. Connect probe cables 13

Step 7. Probe the device under test 14

Step 8. Make measurements 15

Caring for LogicWave 16

To clean the instrument 16

2 Specifications and Characteristics

Specifications 19

Characteristics 20

General 20

Timing Analysis 20

State Analysis 21

Triggering 21

Probes 21

Operating Environment 22

Contents

Setting Up LogicWave

Shows how to install the Agilent Technologies LogicWave logic analyzer

and provides instructions on caring for the instrument.

Chapter 1: Setting Up LogicWave

Installing LogicWave

This section provides instructions for setting up the LogicWave logic

analyzer and connecting it to a device under test.

The logic analyzer user interface requires a host computer (PC) with

the following characteristics (or better):

•Pentium 90 MHz

•Windows 95/98/NT/2000

•16MB RAM

•10MB available space on the hard disk drive

•Available parallel port (no pass-through devices installed)

•Available LPT1 peripheral device designator

The host computer (PC) running the logic analyzer interface can be

either powered on or off. The interface software is installed on the PC.

Chapter 1: Setting Up LogicWave

Installing LogicWave

Step 1. Connect the logic analyzer to a host

computer (PC)

1Connect the small end of an HP C2946A parallel port printer

cable to the PARALLEL connector on the rear panel of the logic

analyzer

2Connect the large end of the printer cable to the PC’s parallel

port.

3Apply power to the PC if it is not turned on.

To ensure the PC’s parallel port is properly configured, interrupt the

PC’s boot process by pressing [ F2 ] on the keyboard. Scroll down to

the parallel port configuration and observe the current parallel port

data transfer mode. Ensure either Enhanced Capabilities Port (ECP),

Byte, or Nibble mode is selected (Enhanced Parallel Port (EPP) mode

will not work). If none of the correct transfer modes is selected, you

need to change the transfer mode according to the instructions for

your PC.

Chapter 1: Setting Up LogicWave

Installing LogicWave

Step 2. Connect the power cable

CAUTION: Use only the supplied power supply (HP F1044B) and cord. Failure to use the

proper power supply could result in equipment damage.

1Connect the power cord to the power supply input.

2Connect the power supply output cable to the power input

connector on the rear panel of the logic analyzer.

Chapter 1: Setting Up LogicWave

Installing LogicWave

Step 3. Turn on power

CAUTION: Do not block the air intake vents on the bottom of the logic analyzer.

1Turn the power switch to the on (“1”) position.

2Wait approximately 15 seconds for the logic analyzer to power up

and settle.

Chapter 1: Setting Up LogicWave

Installing LogicWave

Step 4. Install software

See Also Refer to the instructions on the installation CD.

Table of contents

Other Agilent Technologies Measuring Instrument manuals

Agilent Technologies

Agilent Technologies U1461A User manual

Agilent Technologies

Agilent Technologies U1401B User manual

Agilent Technologies

Agilent Technologies N1911A User manual

Agilent Technologies

Agilent Technologies 8712ET User manual

Agilent Technologies

Agilent Technologies 1290 Infinity II 2D-LC Solution User manual

Agilent Technologies

Agilent Technologies EMC Series User manual

Agilent Technologies

Agilent Technologies E4980A User manual

Agilent Technologies

Agilent Technologies U2722A User manual

Agilent Technologies

Agilent Technologies ESA-E E4407B Installation and operation manual

Agilent Technologies

Agilent Technologies E4445A PSA Series Quick start guide

Agilent Technologies

Agilent Technologies U1211A User manual

Agilent Technologies

Agilent Technologies 4294A User manual

Agilent Technologies

Agilent Technologies E7401A User manual

Agilent Technologies

Agilent Technologies U2300A Series User manual

Agilent Technologies

Agilent Technologies 71612 User manual

Agilent Technologies

Agilent Technologies N1913a User manual

Agilent Technologies

Agilent Technologies N2797A User manual

Agilent Technologies

Agilent Technologies E4416A User manual

Agilent Technologies

Agilent Technologies FieldFox N9912A User manual

Agilent Technologies

Agilent Technologies Agilent E6474A User manual

Agilent Technologies

Agilent Technologies HP 8719D User manual

Agilent Technologies

Agilent Technologies 3200 Series User manual

Agilent Technologies

Agilent Technologies Agilent 8163A Operating instructions

Agilent Technologies

Agilent Technologies 8719ES User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual