Agilent Technologies E5061B User manual

Agilent E5061B

Network Analyzer

Conﬁguration Guide

Ordering guide

Standard furnished item 1

Description Additional information

Installation guide Contains the information necessary to start up with the E5061B.

CD ROM IO libraries

Power cable

Certiﬁcate of calibration

Step 1. Choose test set option (Must choose one of the nine test set options.)

Option No. Description

50 Ω RF NA options

E5061B-115 Transmission/Reﬂection test set, 100 kHz to 1.5 GHz, 50 Ω system impedance

E5061B-215 S-parameter test set, 100 kHz to 1.5 GHz, 50 Ω system impedance

E5061B-135 Transmission/Reﬂection test set, 100 kHz to 3 GHz, 50 Ω system impedance

E5061B-235 S-parameter test set, 100 kHz to 3GHz, 50 Ω system impedance

75 Ω RF NA options

E5061B-117 Transmission/Reﬂection test set, 100 kHz to 1.5 GHz, 75 Ω system impedance

E5061B-217 S-parameter test set, 100 kHz to 1.5 GHz, 75 Ω system impedance

E5061B-137 Transmission/Reﬂection test set, 100 kHz to 3 GHz, 75 Ω system impedance

E5061B-237 S-parameter test set, 100 kHz to 3GHz, 75 Ω system impedance

LF-RF NA option

E5061B-3L5 LF-RF network analyzer with DC bias source, 5 Hz to 3 GHz

Step 2. Choose impedance analysis option

(for E5061B-3L5 LF-RF network analyzer. If not required, go to step 3.)

Option No. Description

Software option

E5061B-005 2, 3 Impedance analysis for E5061B-3L5 LF-RF network analyzer

Accessory

E5061B-720 3, 4 Add 50 Ω resistor set

The following steps will guide you through configuring your E5061B.

1. Keyboard and mouse are not furnished as standard. Refer to “Step 6. accessory option” for the selection of these items.

2. This option is not applicable for the E5061B RF NA options 1x5/2x5/1x7/2x7.

3. Refer to “Software upgrade” section for retroﬁt information on the above option.

4. For calibration at test ﬁxtures. Required for the gain-phase series-thru method.

Step 3. Choose hardware option (If not required, go to step 4)

Option No. Description

E5061B-1E5 1High stability time base

Step 4. Choose hard disk drive option 2

Option No. Description

E5061B-020 Standard hard disk drive

Step 5. Choose software option (If not required, go to step 6)

Option No. Description

E5061B-010 3Time domain/fault location analysis

Step 6. Choose accessory option (If not required, go to step 7)

Option No. Description

E5061B-810 Add keyboard

E5061B-820 Add mouse

E5061B-1CM Rack mount Kit

E5061B-1CN Front Handle Kit

E5061B-1CP Rack mount and front handle kit

Step 7. Choose calibration option

Option No. Description

E5061B-1A7 ISO 17025 compliant calibration

E5061B-A6J ANSI Z540 compliant calibration

1. Refer to “Hardware upgrade” section for retroﬁt information on the above options.

2. Option 020 is the only hard disk option for the E5061B. Must choose this option when ordering the E5061B.

3. Refer to “Software upgrade” section for retroﬁt information on the above option.

E5061BEP ENA Network Analyzer – Express Conﬁguration

The Agilent E5061BEP ENA series network analyzer express configurations are preconfigured option packages for off-the-

shelf delivery from our authorized distributors. The express configurations deliver the same specifications and functionality

as Agilent’s build-to-order instruments and also provide the same level of upgradeability, ensuring that they can evolve as

your test needs change. For more detail, visit, www.agilent.com/find/express-e5061b

Step 3. Choose hardware option (If not required, go to step 4)

Option No. Description

E5061BEP ENA Series Network Analyzer – Express Conﬁguration

Step 3. Choose hardware option (If not required, go to step 4)

Option No. Frequency Test set Connector

Type

Impedance

analysis

Equivalent standard model

option 1

E5061BEP-115 100 kHz to 1.5 GHz Transmission/ Reﬂection Type-N(f) No E5061B-115/020

E5061BEP-235 100 kHz to 3 GHz S-parameter Type-N(f) No E5061B-115/020

E5061BEP-NZA 5 Hz to 3 GHz S-parameter and

Gain-phase

Type-N(f) and

BNC(f)

Yes E5061B-3L5/020/005/720/1E5

1. Equivalent standard model options

Option 3L5 : LF-RF network analyzer with DC bias source, 5 Hz to 3 GHz

Option 020 : Standard hard disk drive

Option 005 : Impedance analysis for LF-RF network analyzer

Option 720 : Add 50 Ω resistor set

Option 1E5 : High stability time base

Test accessories and calibration kits

Electronic calibration (ECal) modules

Test accessories and calibration kits that can be used with the E5061B are listed in this section. A complete line of test

accessories and calibration kits can be found at the Agilent RF and Microwave Test Accessories Web site:

www.agilent.com/find/accessories

Test accessories

Test accessories such as test port cable are necessary for a complete measurement system using the E5061B. Order test

accessories in accordance with the desired measurement system.

Calibration kits

Calibration is an accuracy enhancement procedure that effectively reduces the system errors that cause uncertainty in

network measurement. Calibration kit is necessary to perform the calibration.

• Mechanical calibration kits include standards, such as opens, shorts and loads, which are measured by the network

analyzer. Choose a calibration kit for each connector type to be used.

• Electronic calibration (ECal) modules1replace mechanical calibration standards with one solid-state calibration module

that is controlled by the network analyzer via USB. ECal modules provide many different impedances to the test ports

which enables a full two-port calibration to be performed quickly with a single connection. This technique reduces

operator errors and connector wear and abrasion.

1. ECal modules don’t cover the whole frequency range of the E5061B. Check whether the frequency range of each ECal module meets your

measurement needs.

Mechanical calibration kits

1. For transmission measurement with the gain-phase test port of the E5061B-3L5. Required for milliohm impedance measurements in the low

frequency range.

Test accessories (for 50 Ω system)

Model No. Description

Test Port Cable

N6314A 50 Ω type-N (m) to type-N (m) cable, DC to 12.4 GHz, 61 cm (24 in)

N6315A 50 Ω type-N (m) to type-N (f) cable, DC to 12.4 GHz, 61 cm (24 in)

11500E 3.5 mm (m) to 3.5 mm (m) cable, 61 cm (24 in)

11500F 3.5 mm (m) to 3.5 mm (m) cable, 150 cm (24 in)

11857D 50 Ω 7 mm to 7 mm cable, 300 kHz to 6 GHz, 61 cm (24 in)

8120-1838 50 Ω BNC (m) to BNC (m) cable, 30 cm (12 in)

8120-1839 50 Ω BNC (m) to BNC (m) cable, 61 cm (24 in)

Adapter

1250-0780 50 Ω type-N (m) to 50 Ω BNC (f) adapter

1250-1200 50 Ω BNC (f) to SMA (m) adapter

1250-2015 50 Ω BNC (m) to SMA (f) adapter

Accessory Kit

11853A 50 Ω type-N accessory kit. Includes;

- Type-N (f) to type-N (f) adapter (2 qty.)

- Type-N (m) to type-N (m) adapter (2 qty.)

- Type-N (f) short

- Type-N (m) short

11854A 50 Ω BNC accessory kit. Includes;

- BNC (m) to Type-N (m) adapter (2 qty.)

- BNC (f) to Type-N (f) adapter (2 qty.)

- BNC (f) to Type-N (m) adapter (2 qty.)

- BNC (m) to Type-N (f) adapter (2 qty.)

- BNC (m) short

Adapter Kit

11878A 50 Ω type-N to 3.5 mm adapter kit. Includes;

- 3.5 mm (m) to type-N (m) adapter

- 3.5 mm (f) to type-N (f) adapter

- 3.5 mm (f) to type-N (m) adapter

- 3.5 mm (m) to type-N (f) adapter

Power Splitter 1

11667L BNC (f) connectors, DC to 2 GHz

DC Block

N9398C 3.5 mm (m) and 3.5 mm (f) connectors, 50 kHz to 26.5 GHz

N9399C 3.5 mm (m) and 3.5 mm (f) connectors, 700 kHz to 26.5 GHz

11667L

Test accessories (for 50 Ω system, continued)

Model No. Description

Active Probe

41800A 5 Hz to 500 MHz active probe, 100 kΩ (probe alone) / 1 MΩ (with 10:1 or 100:1 divider). Includes;

- Probe to BNC adapter

- Hook tip adapter

- Slip-on tip adapter

- 10:1 and 100:1 divider

41800A-001 Adds a cable to connect the probe with an external power supply. This option is not necessary for

the E5061B-3L5 since it is equipped with the probe power.

41800A-UK6 Commercial cal certiﬁcate with test data

85024A 300 kHz to 3 GHz active probe. Includes;

- Probe tip to type-N Adapter

- 10:1 divider

- Hook tip adapter

- Slip-on tip adapter

- Leads

Differential Active Probe

1141A 1DC to 200 MHz differential active probe. The 1142A is required. Includes;

- 10x and 100x attenuator adapter

- AC coupling adapter

- Two-inch extension leads

- Mini-grabbers (2 qty.)

- Five-inch ground lead

- Shielded signal lead

- Test board

- Flat-blade alignment tool

- Circuit connection post

Probe Control and Power

Module

1142A Probe control and power module for the 1141A Differential Active Probe.

1. The 1142A Probe Control and Power Module is required.

1141A, 1142A, and E5061B41800A and E5061B

Non-Agilent test accessories (for 50 Ω system)

Model No. Description

Injection Transformer

Picotest

J2100A Injection Transformer

1 Hz to 5 MHz (when terminated with 5 Ω), 10 Hz to 5 MHz (when terminated with

50 Ω), Input: BNC(f), Output: Banana jacks, 600 V/CAT II isolation voltage.

Optimized for loop gain measurements of DC-DC converters and switching power

supplies.

Picotest

J2101A Injection Transformer

10 Hz to 45 MHz (when terminated with 5 Ω), 60 Hz to 45 MHz (when terminated with

50 Ω), Input: BNC(f), Output: Banana jacks, 600 V/CAT II isolation voltage.

Optimized for loop gain measurements of DC-DC converters and switching power

supplies.

North Hills Signal Processing

0017CC 50 Ω Video Isolation

Transformer

10 Hz to 5 MHz (when terminated with 50 Ω), Input: BNC(f), Output: BNC(f).

Applicable to loop gain measurements of DC-DC converters and switching power

supplies.

Other Signal Injector

Picotest

J2110A Solid-State Injector

(Bode Box)

DC to 40 MHz, Input and output voltage up to ± 10.5 V,

Signal input: BNC(f), Output: Banana jacks.

Optimized for wide band loop gain measurements of control loop circuits.

Picotest

J2120A Line Injector

15 Hz to 5 MHz, up to 50 Vdc / 5 Adc, Signal input: BNC(f),

DC input & output: Banana jacks.

For PSRR measurements of linear regulators and DC-DC converters.

Picotest

J2111A Current Injector

DC to 40 MHz, Input: BNC(f), Output: Banana jacks.

For the non-invasive phase margin measurement and other measurements of DC-DC

converters (refer to Picotest’s application note).

Banana test lead/adapter

Pomona Electronics 1166 Banana plug to alligator clip

Pomona Electronics 4650 Banana plug to test clip

Pomona Electronics 4650 Banana plugs to test clips

Pomona Electronics 1269 Banana plugs to BNC(f) adapter

BNC breakout

Pomona Electronics 2886 BNC(m) to alligator clips

Pomona Electronics 3789 BNC(m) to test clips

BNC to test clip lead

Pomona Electronics 3787-C-18 Coax. cable with a BNC(m) connector and test clips at the ends,

approx. 60 cm (total length).

For probing the DUT from the gain-phase receiver ports.

50 Ω feed through

Pasternack Enterprises

PE6008-50

DC to 1 GHz, 50 Ω BNC(m) to BNC(f) feed through.

DC Block

Mini-Circuits

BLK-89

100 kHz to 8 GHz, 50 Ω SMA(m) to SMA(f) DC blocking capacitor.

Non-Agilent test accessories (for 50 Ω system, continued)

North Hills Signal Processing 0017CC

Pomona 3787-C-18 test lead (connected to gain-phase receiver ports)

Pomona 2886 BNC breakout (connected to 0017CC)

Picotest J2100A Injection Transformer

Picotest J2111A Current Injector

Picotest J2120A Line Injector

(Banana-to-test clip leads connected to its banana jacks)

Picotest web page: http://www.picotest.com

North Hills Signal Processing web page: http://www.northhills-sp.com/index.html

Mini-Circuits web page: http://www.minicircuits.com/index.html

Pomona Electronics web page: http://www.pomonaelectronics.com/

Pasternack Enterprises web page: http://www.pasternack.com/

Calibration kits (for 50 Ω system)

Model No. Description

Type-N

Mechanical calibration kits

85032E 50 Ω economy calibration kit, DC to 6 GHz. Includes;

- Type-N (m) ﬁxed load

- Type-N (m) combined open/short

85032F 50 Ω standard calibration kit, DC to 9 GHz. Includes;

- Type-N (m) ﬁxed load

- Type-N (f) ﬁxed load

- Type-N (m) Open

- Type-N (f) Open

- Type-N (m) Short

- Type-N (f) Short

85032F-100 Adds 50 Ω type-N (f) to type-N (f) adapter

85032F-200 Adds 50 Ω type-N (m) to type-N (m) adapter

85032F-300 Adds 50 Ω type-N (m) to type-N (f) adapter

85032F-500 Adds;

- 50 Ω type-N (m) to 7 mm adapter (2 qty.)

- 50 Ω type-N (f) to 7 mm adapter (2 qty.)

Electronic calibration kits

85092C 1RF ECal module

2-port (50 Ω type-N), 300 kHz to 9 GHz. The sexes of the connectors depend on the option.

85092C-M0F 2Type-N (f) to Type-N (m) RF ECal module

85092C-00M 2Type-N (m) to Type-N (m) RF ECal module

85092C-00F 2Type-N (f) to Type-N (f) RF ECal module

85092C-00A Adds;

- Type-N (f) to Type-N (f) adapter

- Type-N (m) to Type-N (m) adapter

1. This ECal module cannot be used in the low frequency range below 300 kHz.

2. Mixed connector options are also available. Visit our website for more details about the ECal: www.agilent.com/ﬁnd/ecal

Other manuals for E5061B

Table of contents

Other Agilent Technologies Measuring Instrument manuals

Agilent Technologies

Agilent Technologies U3051C Owner's manual

Agilent Technologies

Agilent Technologies U1701A User manual

Agilent Technologies

Agilent Technologies N9010A User manual

Agilent Technologies

Agilent Technologies U1401B User manual

Agilent Technologies

Agilent Technologies MXA Series Installation and operation manual

Agilent Technologies

Agilent Technologies 8510C Owner's manual

Agilent Technologies

Agilent Technologies 4395A Owner's manual

Agilent Technologies

Agilent Technologies FRG-700 User manual

Agilent Technologies

Agilent Technologies 8510C User manual

Agilent Technologies

Agilent Technologies 4352B User manual

Agilent Technologies

Agilent Technologies 4200 FlexScan User manual

Agilent Technologies

Agilent Technologies 4263B User manual

Agilent Technologies

Agilent Technologies 16902A User manual

Agilent Technologies

Agilent Technologies E4991A User manual

Agilent Technologies

Agilent Technologies Agilent 8163A Operating instructions

Agilent Technologies

Agilent Technologies U1731A User manual

Agilent Technologies

Agilent Technologies E7401A User manual

Agilent Technologies

Agilent Technologies E8364BPNA Series Quick start guide

Agilent Technologies

Agilent Technologies 87075C Option H08 Manual

Agilent Technologies

Agilent Technologies 8564EC User manual

Agilent Technologies

Agilent Technologies U1701A User manual

Agilent Technologies

Agilent Technologies E5072A User manual

Agilent Technologies

Agilent Technologies ESA Series User manual

Agilent Technologies

Agilent Technologies E4419B User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual