Agilent Technologies 4339B User manual

Manual Change

This manual change describes the procedure when use the Agilent 16353A/16353H

Standard Resistor Set instead of the Agilent 16340A RC-Box in 4339B Performance Test.

When use the Agilent 16340A RC-Box, refer to the Chapter 9 (Maintenance) in this

manual.

Manual Change

Test Equipment

Table 1 lists the recommended equipment for performing 4339B maintenance.

Table 1 Required Equipment

Equipment Requirements Recommended

Model Qty. Use*1

DC Voltmeter

StandardResistor

Set

10 kΩResistor

RC Box Adapter

V Measurement

Adapter

BNC(F)-TXA

Ground Open (F)

Adapter

BNC(F)-(F)

Adapter

Cable

Handler Interface

Tester

Voltage Range: 0V to 1000V

Accuracy: <0.04%

No substitute

Banana-Banana Jumper

Dual Banana-BNC(m) Cable

No Substitute

3458A

16353A/16353H

42038A

PN 04339-65005

PN 04339-65006

PN 1250-1830

11058A

PN 11001-60001

PN 04339-65007

P, F

*1.P: Performance Tests, F: Functional Tests

Manual Change

Performance Tests

Introduction

This section provides the test procedures used to verify that the 4339B’s specifications

listed in Chapter 8, General Information, of this manual are met. All tests can be performed

without access to the interior of the instrument. The performance tests can also be used to

perform incoming inspection, and to verify that the 4339B meets its performance

specifications after troubleshooting or adjustment. If the performance tests indicate that the

4339B is NOT operating within the specified limits, check your test setup, then proceed

with troubleshooting if necessary.

NOTE Allow the 4339B to warm up for at least 30minutes before you execute any of the

performance tests.

NOTE Perform all performance tests in ambient conditions of 23°C±5°C, ≤70% RH.

Test Equipment

Table 1 lists the test equipment required to perform the tests described in this section. Use

only calibrated test instruments when performance testing the 4339B4. Equipment which

equals or surpasses the key required specifications of the recommended equipment may be

used as a substitute.

Calculation Sheet

The calculation sheet is used as an aid for recording raw measurement data, and for

calculating the performance test results.

The performance test procedure gives the test sequence for performing a test. The complete

set of measurement data is recorded on the calculation sheet. The results are calculated

using the equations given on the calculation sheet, and the result are transcribed to the

performance test record.

The procedure for using the calculation sheet is:

1. Photocopy the calculation sheet.

2. Follow the performance test procedure and record the measurement value(s), the

4339B’s reading, etc., into the specified column on the calculation sheet.

3. Calculate the test result using the appropriate equation given on the calculation sheet,

and record the test result into the Test Result column of the performance test record.

Manual Change

Performance Tests

Performance Test Record

Record the performance test results in the test record at the end of this chapter (Photocopy

the test record and use the photocopy). The test record lists all test specifications, their

acceptable limits, and measurement uncertainties for the recommended test equipment.

Test results recorded during incoming inspection can be used for comparison purposes

during periodic maintenance, troubleshooting, and after repair or adjustment.

Calibration Cycle

The 4339B requires periodic performance tests. The frequency of performance testing

depends on the operating and environmental conditions under which the 4339B is used.

Verify the 4339B’s performance at least once a year, using the performance tests described

in this section.

Manual Change

Source Voltage Accuracy Test

The 4339B’s source voltage is measured with a DC voltmeter.

Specification

Test Equipment

Procedure

WARNING When the High Voltage indicator is lit, the 4339B outputs high voltages of up to 1000

Vdc maximum.

Step 1. Reset the 4339B using the following procedure:

1. Press [blue][⋅] to display the system reset menu.

2. Select Yes using [←][↓]or [↑][→] and press [Enter].

Step 2. Set up the equipment as shown in Figure 1.

Source Voltage (Vs) Accuracy: ±(0.16 % + 100mV) (Vs≤200V)

±(0.16 % + 500mV) (Vs>200V)

Description Recommended Model

Multimeter 3458A

V Measurement Adapter PN 04339-65006

Banana-Banana Jumper 11508A

Manual Change

Source Voltage Accuracy Test

Figure 1 Source Voltage Accuracy Test Setup

Step 3. Press the 3458A Multimeter’s [DCV] to set the measurement mode to DC voltage.

Step 4. Set the V Measurement Adapter’s ID switches and Output switch as follows:

Step 5. On the 4339B, press [V Output] to turn the source voltage ON. (V Output indicator turns

ON.)

Step 6. Record the multimeter reading on the calculation sheet. (Initial output voltage setting is 0

V.)

Step 7. Press [V Output] to turn the source voltage OFF. (V Ouptut indicator turns OFF.)

Step 8. Calculate the test result according to the calculation sheet, and record the result into the

performance test record.

Step 9. Perform this test for all the voltage settings listed in Table 2. The source voltage must be

turned OFF after each test. The source voltage can be changed using the following

procedure :

1. Press [Source Voltage] to display the source voltage setup menu.

2. Use the numeric keys to enter a desired voltage, and press [Enter].

Switch Setting

ID1 0

ID2 0

ID3 0

ID4 1

Output Enable

4339boe1001

1234

Output

4339B

Shunt Connector

RedBlack

Black

Red

V Measurement

Adapter

Multimeter

Banana-Banana Jumper

Manual Change

Source Voltage Accuracy Test

3. The desired voltage will be displayed.

Table 2 Source Voltage Accuracy Test Settings

Source Voltage

Setting

10V

25V

50V

100V

200V

201V

250V

500V

1000V

Manual Change

Source Voltage Accuracy Test

Ammeter Offset Voltage and Input Resistance Test

The 4339B’s ammeter offset voltage and input resistance are measured.

Specification

Test Equipment

Procedure

Ammeter Offset Voltage Test.

Step 1. Reset the 4339B using the following procedure:

1. Press [blue][⋅] to display the system reset menu.

2. Select Yes using [←][↓] or [↑][→] and press [Enter].

Step 2. Set up the equipment as shown in Figure 2.

Figure 2 Ammeter Offset Voltage Test Setup

Ammeter Offset Voltage: ≤0.5mV

Ammeter Input Resistance: 1 kΩ±5%

Description Recommended Model

Multimeter 3458A

RC Box Adapter PN 04339-65005

Dual Banana-BNC(m) Cable PN 11001-60001

42038A 10 kΩResistor 42038A

4339boe1002

4339B

To Monitor L

Dual Banana-BNC(m) Cable

: No Connection

RC Box

Adapter

Multimeter



Manual Change

Source Voltage Accuracy Test

Step 3. Set the RC Box Adapter switch to the Fposition.

Step 4. Press the 3458A Multimeter’s [DCV] to set the measurement mode to DC voltage.

Step 5. Press the 4339B’s [Meas time] to set the measurement time to SHORT. The current

measurement time setting is indicated by the Meas Time annunciator.

Step 6. Set the measurement range to 100 μA using the following procedure:

1. Press [blue][Auto Hold] to display the measurement range setup menu.

2. Press [↑][→] untill 100 μA appears, and press [Enter].

Step 7. Press [Trig Mode] to set the trigger mode to Manual. The current trigger mode setting is

indicated by the Trigger annunciator.

Step 8. Record the multimeter reading into the performance test record. Do not change the

equipment setup for the following ammeter input resistance test.

Ammeter Input Resistance test.

Step 9. Record the 42038A 10 kΩcalibration value and the ammeter offset voltage test result on

the calculation sheet.

Step 10. Connect the 42038A to the RC Box Adapter as shown in Figure 3.

Figure 3 42038A Connection

Step 11. Set the source voltage to 1V using the following procedure:

1. Press [Source Voltage] to display the source voltage setup menu.

2. Press [1][Enter] to set the source voltage to 1V.

3. Comfirm that +1V is displayed on the right side of the LCD.

Step 12. Press [V Output] to turn the source voltage ON. (V Output indicator turns ON.)

Step 13. Record the multimeter reading on the calculation sheet on the L Voltage line.

Step 14. Disconnect the Dual Banana-BNC(m) cable from the Monitor L terminal and connect it to

the Monitor H terminal.

Step 15. Record the multimeter reading on the calculation sheet on the H Voltage line.

4339boe1003

RC Box Adapter

Direct connection, no cable

BNC Cable

42038A

BNC(F)-Txa(F)

Adapter

BNC(F)-(F)

Adapter

Manual Change

Source Voltage Accuracy Test

Step 16. Calculate the test result according to the calculation sheet, and record the result into the

performance test record.

Current Measurement Accuracy Test

The 4339B measures the current through the calibrated 16353A/16353H , and the

measured values are compared with the current values calculated from the

16353A/16353H’s calibration value and the voltage across the standard.

Specification

Test Equipment

Procedure

Step 1. Record the 16353A/16353H Standard Resistor Set calibration values on the calculation

sheet.

Step 2. Reset the 4339B using the following procedure:

1. Press [blue] [⋅] to display the system reset menu.

2. Select Yes using [←][↓] or [↑] [→] and press [Enter].

Step 3. Set the Offset-error Canceling to ON using the following procedure:

1. Press [blue][-] to display the configuration setting menu.

2. Select Offset using [←][↓] or [↑][→] and press [Enter].

3. Select On using [←][↓] or [↑][→] and press [Enter].

4. Select Exit and press [Enter] to exit the configuration setting menu.

Step 4. Set up the equipment as shown in Figure 4.

Basic Measurement Accuracy: ±0.4% (See Chapter 8 General Information for

details.)

Description Recommended Model

Multimeter 3458A

Standard Resistor Set 16353A, 16353H

RC Box Adapter PN 04339-65005

Dual Banana-BNC(m) Cable PN 11001-60001

Other manuals for 4339B

This manual suits for next models

Table of contents

Other Agilent Technologies Measuring Instrument manuals

Agilent Technologies

Agilent Technologies 8614 B Series User manual

Agilent Technologies

Agilent Technologies 55B AA User manual

Agilent Technologies

Agilent Technologies 89410A User manual

Agilent Technologies

Agilent Technologies U1461A User manual

Agilent Technologies

Agilent Technologies 89604 User manual

Agilent Technologies

Agilent Technologies E8364BPNA Series Quick start guide

Agilent Technologies

Agilent Technologies 6800 Series Quick start guide

Agilent Technologies

Agilent Technologies E5080 Series User manual

Agilent Technologies

Agilent Technologies OmniBER OTN Series User manual

Agilent Technologies

Agilent Technologies HP 5890 II Series User manual

Agilent Technologies

Agilent Technologies 8719ET User manual

Agilent Technologies

Agilent Technologies 8564EC User manual

Agilent Technologies

Agilent Technologies 16900 Series User manual

Agilent Technologies

Agilent Technologies 4263B User manual

Agilent Technologies

Agilent Technologies N2797A User manual

Agilent Technologies

Agilent Technologies E4915A User manual

Agilent Technologies

Agilent Technologies UXA N9040B Installation and operation manual

Agilent Technologies

Agilent Technologies Agile or Elusive Signals Using Manual

Agilent Technologies

Agilent Technologies 4156b User manual

Agilent Technologies

Agilent Technologies ESA-E E4404B User manual

Agilent Technologies

Agilent Technologies DSOX4USBSQ USB 2.0 User manual

Agilent Technologies

Agilent Technologies ICP-MS Series Operating instructions

Agilent Technologies

Agilent Technologies Acqiris DC110 User manual

Agilent Technologies

Agilent Technologies 3200 Series User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual