ABB SmartMedia SM2000 Installation instructions
1
INFORMATION
No. INF02/61 Date: June 2002 Product:SM2000 Videographic Recorder
Manual: IM/SM2000
SM2000
Compact Flash Hardware Installation
noitpircseD.oNtraPytQ
ylbmessA-buShsalFtcapmoC2600/0002RG1
wercS01x5.2M32811B2
kniLBCP0529B2
tcapmoC0002MS–teehSnoitamrofnI noitallatsnIerawdraHhsalF 16/20FNI1
2 Tools Required
• Medium, flat-bladed screwdriver
• No. 1 Pozidriv screwdriver
3 Fitting Media Board
Sub-Assembly – Figs. 3.1 to 3.5
Caution. The instrument is vulnerable to
electrostatic damage. Wear an anti-static strap or
dismantle the unit on an anti-static workbench.
1) Isolate the instrument from the power supply.
2) Remove the instrument from its case – see Fig. 3.1.
1 Introduction
This Information Sheet describes the procedure for fitting
Compact Flash hardware to SM2000 instruments.
The Compact Flash Media Service Pack, GR2000/0700,
includes the following items:
Withdraw the instrument
from the case
Remove tamper-proof seal
(if fitted)
Unscrew the jacking screw
1
23
Fig. 3.1 Removing the Instrument from its Case
Information. Refitting is the
reverse of removal.
2
Remove pozidriv screws
(one each side)
Lift up top cover
Remove top cover
Remove PCB locking bar
1
2
3
1
4
Fig. 3.2 Removing the Chassis Top Cover and PCB Locking Bar
4) Remove the existing media board sub-assembly –
see Fig. 3.3.
…3 Fitting Media Board
Sub-Assembly – Figs. 3.1 to 3.5
3) Remove the chassis top cover and PCB locking bar –
see Fig. 3.2.
Remove pozidriv screws
(1 each side)
Disconnect configurator
board ribbon cable
Lift main board from
motherboard and withdraw
media board
3
5
Lift black
retaining flap
Disconnect
flexi-circuit
2
1
Media board
Main board
4
✶
Note. Flexi-circuit is not present if
neither Compact Flash nor SmartMedia
option is already fitted to the instrument.
Information. Refitting is the
reverse of removal.
Fig. 3.3 Removing the Media Board Sub-Assembly
3
8) Refit the instrument to the case – see Fig. 3.1.
9) Restore the power supply to the instrument.
1Check that PCB link LK1
is fitted and is in the
correct position for
Compact Flash hardware.
LK
1
5V Position
SmartMedia
LK
1
3.3V Position
Compact Flash
LK1
LK1
Fig. 3.4 PCB Link LK1 Positions
6) Fit the new media board sub-assembly – see Fig. 3.3.
7) Refit the PCB locking bar and chassis top cover –
see Fig. 3.5.
…3 Fitting Media Board
Sub-Assembly – Figs. 3.1 to 3.5
5) Check the position of PCB link LK1 – see Fig. 3.4.
EMC Contacts
Position top cover as shown
Slide forward
Lower rear
Refit pozidriv screws
(one each side)
Refit PCB locking bar
ensuring the slots
in the bar locate correctly
on the boards and chassis
1
2
3
4
5
5
Caution. When positioning the
chassis top cover, take care not to
damage the EMC contacts.
Fig. 3.5 Refitting the PCB Locking Bar and Chassis Top Cover
4
INF02/61 Issue 1
The Company’s policy is one of continuous product
improvement and the right is reserved to modify the
information contained herein without notice.
Printed in UK (06.02)
© ABB 2002
ABB Limited
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: +44 (0)1480 475 321
Fax: +44 (0)1480 217 948
ABB Inc.
125 E. County Line Road
Warminster, PA 18974
USA
Tel: +1 215-674-6000
Fax: +1 215-674-7183
ABB has Sales & Customer Support expertise in over
100 countries worldwide
www.abb.com
Other manuals for SmartMedia SM2000
5
Other ABB Measuring Instrument manuals
ABB
ABB CoriolisMaster FCH400 Series User manual
ABB
ABB EXCOUNT-II User manual
ABB
ABB ADS420 User manual
ABB
ABB AquaMaster Explorer User manual
ABB
ABB Aztec 600 User manual
ABB
ABB 6553 Series User manual
ABB
ABB BAMU-12C User manual
ABB
ABB Relion RES670 User manual
ABB
ABB SM1000 User manual
ABB
ABB IM300-I Quick start guide
ABB
ABB FEX300 User manual
ABB
ABB Stanilite Nexus LX User manual
ABB
ABB Relion 670 Series RES670 User manual
ABB
ABB TMD-T4 User manual
ABB
ABB FEF series User manual
ABB
ABB Levelmeter 2000 User manual
ABB
ABB Navigator 600 Phosphate User manual
ABB
ABB Endura AZ20 series User manual
ABB
ABB 2117 U-500 User manual
ABB
ABB 10D1477 User manual
