ABB C13 User manual

C13

INSTALLATION MANUAL

Contents

Disclaimer ......................................................................................... 2

Trademark......................................................................................... 2

Introduction ....................................................................................... 3

Product Overview.............................................................................. 3

Installation ......................................................................................... 6

Installation Requirements.................................................................. 7

Troubleshooting ................................................................................ 7

Service and Maintenance.................................................................. 8

C13_install.book Page 1 Thursday, May 30, 2013 4:36 PM

Disclaimer

The information in this document is subject to change without notice

and should not be construed as a commitment by ABB AB. ABB AB as-

sumes no responsibility for any errors that may appear in this docu-

ment.

In no event shall ABB AB be liable for direct, indirect, special, incidental

or consequential damages of any nature or kind arising from the use of

this document, nor shall ABB AB be liable for incidental or consequen-

tial damages arising from use of any software or hardware described in

this document.

This document and parts thereof must not be reproduced or copied

without written permission from ABB AB, and the contents thereof must

not be imparted to a third party nor used for any unauthorized purpose.

The software or hardware described in this document is furnished un-

der a license and may be used, copied, or disclosed only in accordance

with the terms of such license.

Trademark

ABB AB is a registered trademark of the ABB Group. All other brand or

product names mentioned in this document may be trademarks or reg-

istered trademarks of their respective holders.

C13_install.book Page 2 Thursday, May 30, 2013 4:36 PM

EN EN

Introduction

The C13 meter is a direct connected electricity meter for DIN-rail

mounting in distribution boards or small enclosures.

Read the information in this manual carefully before you install the

equipment.

Product Overview

Part Description

1 Terminal for output connections

C13_install.book Page 3 Thursday, May 30, 2013 4:36 PM

2 Sealing points

3 Push button for programing and reading the meter. For

detailed information, refer to the C11 User Manual.

4 LED, flashes in proportion to the energy measured

5 Display

6 Sealing label

7 Sealable terminal cover

8 Terminal block

Technical Data

Voltage

Voltage range 3 x 220-240/380-415 V (-20% to +15%)

Terminal wire area

Tightening torque

0.5 - 10 mm²

0.8 Nm

Current

- base Ib

- reference Iref

- maximum Imax

- minimum Imin

5 A

40 A

0.25 A

Part Description

C13_install.book Page 4 Thursday, May 30, 2013 4:36 PM

EN EN

Frequency 50 or 60 Hz ± 5%

Accuracy 1% (Cl.1, Cl. B)

Material Polycarbonate in transparent front glass.

Glass reinforced polycarbonate in bottom

case and upper case. Polycarbonate in ter-

minal cover.

Operating temp. -25 °C to +70 °C

Storage temp. -25 °C to +85 °C

Humidity 75% yearly average, 95% on 30 days/year

Resistance to heat Terminal 960°C, cover 650°C (IEC 60695-

2-1)

Outputs

Current 2 - 100 mA

Voltage 5 - 40 VDC

Pulse frequency 100 imp/kWh

Pulse length 200 ms

Terminal wire area 0.5-6 mm²

Tightening torque 0.8 Nm

Pulse indicator(LED)

Technical Data

C13_install.book Page 5 Thursday, May 30, 2013 4:36 PM

Installation

For information about how to mount and install the equipment, follow

the instructions in the Installation Guide at the end of this manual.

E Warning – Working with high voltage is potentially lethal. Per-

sons subjected to high voltage may suffer cardiac arrest, burn

Pulse frequency 1000 imp/kWh

Pulse length 40 ms

EMC compatibility

Impulse voltage test 6 kV 1.2/50μs (IEC 60060-1)

Surge voltage test 4 kV 1.2/50μs (IEC 61000-4-5)

Fast trans. burst test 4 kV ( IEC 61000-4-4 )

Immunity HF-fields 80 MHz - 2 GHz at 10 V/m (IEC61000-4-3)

Immunity conducted 150kHz – 80MHz ( IEC 61000-4-6 )

RF Emission EN 55022, class B (CISPR22)

ESD 15 kV ( IEC 61000-4-2 )

Standards IEC 62052-11, IEC 62053-21 class 1, GB/T

17215.211-2006, GB/T 17215.321-2008

class 1 & 2, GB 4208-2008, EN 50470-1,

EN 50470-3 category B

Technical Data

C13_install.book Page 6 Thursday, May 30, 2013 4:36 PM

EN EN

injuries, or other severe injuries. To avoid such injuries, make

sure to disconnect the power supply before you start the instal-

lation.

Electrical equipment should only be installed, accessed, ser-

viced and maintained by qualified electrical personnel.

E Warning – For safety reasons it is recommended that the

equipment is installed in a way that makes it impossible to

reach or touch the terminal blocks by accident.

The best way to make a safe installation is to install the unit in

an enclosure. Further, access to the equipment should be lim-

ited through use of lock and key, controlled by qualified electri-

cal personnel.

W Warning – The meters must always be protected by fuses on

the incoming side.

Do not operate the equipment outside the specified technical

data.

Installation Requirements

To comply with the protection requirements the meter must be

mounted in protection class IP 51 enclosures, or better, according to

IEC 60259.

Meters with wireless communication should not be installed closer

than 20 cm from people.

Troubleshooting

If the Wicon appear in the display after the installation has been com-

pleted and power has been connected to the meter, refer to the C13

User Manual for detailed information.

C13_install.book Page 7 Thursday, May 30, 2013 4:36 PM

Service and Maintenance

The meter contains no parts that can be repaired or exchanged. A bro-

ken meter must be replaced.

If the meter needs to be cleaned, use a lightly moistened cloth and a

mild detergent to wipe it.

C Caution – Be careful that no liquid gets into the meter since it

may damage the equipment.

C13_install.book Page 8 Thursday, May 30, 2013 4:36 PM

C13

INSTALLATIONSMANUAL

Contents

Friskrivning........................................................................................ 2

Varumärke......................................................................................... 2

Introduktion ....................................................................................... 3

Produktöversikt ................................................................................. 3

Installation ......................................................................................... 7

Installationskrav ................................................................................ 7

Felsökning......................................................................................... 8

Service och underhåll........................................................................ 8

C13_install.book Page 1 Thursday, May 30, 2013 4:36 PM

Friskrivning

Informationen i detta dokument är föremål för ändringar utan föregå-

ende meddelande och ska inte betraktas som ett åtagande från ABB

AB. ABB AB tar inte något ansvar för fel som kan uppträda i detta doku-

ment.

I inget fall ska ABB AB vara ansvarig för direkta, indirekta, speciella,

oförutsedda eller följdskador av något slag eller typ som uppkommer

vid användning av detta dokument, ej heller ska ABB AB vara ansvarig

för oförutsedda eller följdskador som uppkommer vid användning av

mjukvara eller hårdvara som beskrivs i detta dokument.

Detta dokument och delar därav får inte reproduceras eller kopieras

utan skriftligt tillstånd från ABB AB, och innehållet däri får inte vidare-

befordras till tredje part eller användas för något icke godkänt syfte.

Den mjukvara eller hårdvara som beskrivs i detta dokument tillhanda-

hålls under licens och får endast användas, kopieras eller röjas i enlig-

het med villkoren i licensen.

Varumärke

ABB AB är ett registrerat varumärke tillhörande ABB-koncernen. Alla

övriga märkes- eller produktnamn som nämns i detta dokument kan

vara varumärken eller registrerade varumärken som tillhör respektive

innehavare.

C13_install.book Page 2 Thursday, May 30, 2013 4:36 PM

Other manuals for C13

Table of contents

Languages:

Other ABB Measuring Instrument manuals

ABB

ABB AquaMaster Explorer User manual

ABB

ABB ScreenMaster RVG200 User manual

ABB

ABB NGC8206 User manual

ABB

ABB CoriolisMaster FCB100 User manual

ABB

ABB Smart User manual

ABB

ABB CoriolisMaster FCM2000 Training manual

ABB

ABB CoriolisMaster FCB400 User manual

ABB

ABB ProcessMaster FEP630 series User manual

ABB

ABB AX416 User manual

ABB

ABB FAM3200 Series User manual

ABB

ABB AnalyzeIT ZMT Series Operating instructions

ABB

ABB 7651 User manual

ABB

ABB AO2000-LS25 User manual

ABB

ABB MagMaster User manual

ABB

ABB Navigator 600 Silica User manual

ABB

ABB TMD-T4 User manual

ABB

ABB Sensyflow FMT400-VTS User manual

ABB

ABB AX400 Series User manual

ABB

ABB Kent-Taylor AquaProbe User manual

ABB

ABB ProcessMaster wafer FEM610 Series User manual

ABB

ABB Gas Sampling Probe 2 User manual

ABB

ABB PFCL 201 User manual

ABB

ABB Endura AZ40 User manual

ABB

ABB ProcessMaster FEP630 series User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual