ABB ACS800-01 User manual

ACS800

Hardware Manual

ACS800-01 Drives (0.55 to 110 kW)

ACS800-U1 Drives (0.75 to 150 HP)

ACS800 Single Drive Manuals

HARDWARE MANUALS (appropriate manual is included in the

delivery)

ACS800-01/U1 Hardware Manual 0.55 to 110 kW (0.75 to 150 HP)

3AFE64382101 (English)

ACS800-01/U1 Marine Supplement 3AFE 64291275 (English)

ACS800-02/U2 Hardware Manual 90 to 500 kW (125 to 600 HP)

3AFE64567373 (English)

ACS800-04/04M/U4 Hardware Manual 90 to 500 kW (125 to

600 HP) 3AFE64671006 (English)

ACS800-07/U7 Hardware Manual 45 to 560 kW (50 to 600 HP)

3AFE64702165 (English)

ACS800-07/U7 Dimensional Drawings 45 to 560 kW (50 to

600 HP) 3AFE64775421

ACS800-07 Hardware Manual 500 to 2800 kW

3AFE64731165 (English)

ACS800-17 Hardware Manual 75 to 1120 kW

3AFE64681338 (English)

• Safety instructions

• Electrical installation planning

• Mechanical and electrical installation

• Motor control and I/O board (RMIO)

• Maintenance

• Technical data

• Dimensional drawings

• Resistor braking

FIRMWARE MANUALS, SUPPLEMENTS AND GUIDES

(appropriate documents are included in the delivery)

Standard Application Program Firmware Manual

3AFE64527592 (English)

System Application Program Firmware Manual

3AFE63700177 (English)

Application Program Template Firmware Manual

3AFE64616340 (English)

Master/Follower 3AFE64590430 (English)

PFC Application Program Firmware Manual

3AFE64649337 (English)

Extruder Control Program Supplement 3AFE64648543 (English)

Centrifuge Control Program Supplement 3AFE64667246 (English)

Traverse Control Program Supplement 3AFE64618334 (English)

Crane Control Program Firmware Manual 3BSE11179 (English)

Adaptive Programming Application Guide

3AFE64527274 (English)

OPTION MANUALS (delivered with optional equipment)

Fieldbus Adapters, I/O Extension Modules etc.

ACS800-01 Drives

0.55 to 110 kW

ACS800-U1 Drives

0.75 to 150 HP

Hardware Manual

3AFE64382101 Rev E EN

EFFECTIVE: 15.6.2004

Safety instructions

What this chapter contains

This chapter contains the safety instructions which you must follow when installing,

operating and servicing the drive. If ignored, physical injury or death may follow, or

damage may occur to the drive, the motor or driven equipment. Read the safety

instructions before you work on the unit.

To which products this chapter applies

This chapter applies to the ACS800-01/U1, the ACS800-02/U2 and the ACS800-04/

U4.

Use of warnings and notes

There are two types of safety instructions throughout this manual: warnings and

notes. Warnings caution you about conditions which can result in serious injury or

death and/or damage to the equipment. They also tell you how to avoid the danger.

Notes draw attention to a particular condition or fact, or give information on a

subject. The warning symbols are used as follows:

Dangerous voltage warning warns of high voltage which can cause

physical injury and/or damage to the equipment.

General warning warns about conditions, other than those caused by

electricity, which can result in physical injury and/or damage to the

equipment.

Electrostatic discharge warning warns of electrostatic discharge which

can damage the equipment.

Safety instructions

Installation and maintenance work

These warnings are intended for all who work on the drive, motor cable or motor.

Ignoring the instructions can cause physical injury or death.

Only qualified electricians are allowed to install and maintain the drive.

•Never work on the drive, motor cable or motor when main power is applied.

After switching off the input power, always wait for 5 min to let the intermediate

circuit capacitors discharge before you start working on the drive, motor or

motor cable.

Always ensure by measuring with a multimeter (impedance at least 1 Mohm)

that:

1. Voltage between drive input phases U1, V1 and W1 and the frame is close to

0V.

2. Voltage between terminals UDC+ and UDC- and the frame is close to 0 V.

•Do not work on the control cables when power is applied to the drive or to the

external control circuits. Externally supplied control circuits may cause

dangerous voltages inside the drive even when the main power on the drive is

switched off.

•Do not make any insulation or voltage withstand tests on the drive or drive

modules.

•When reconnecting the motor cable, always check that the phase order is

correct.

Note:

•The motor cable terminals on the drive are at a dangerously high voltage when

the input power is on, regardless of whether the motor is running or not.

•The brake control terminals (UDC+, UDC-, R+ and R- terminals) carry a

dangerous DC voltage (over 500 V).

•Depending on the external wiring, dangerous voltages (115 V, 220 V or 230 V)

may be present on the terminals of relay outputs RO1 to RO3.

•ACS800-04: the busbar ends on both sides of the pedestal are at a

dangerously high voltage when the input power is on, regardless of whether the

motor is running or not.

•ACS800-02 with enclosure extension: The main switch on the cabinet door

does not remove the voltage from the input busbars of the drive. Before working

on the drive, isolate the whole drive from the supply.

Safety instructions

WARNING! The printed circuit boards contain components sensitive to electrostatic

discharge. Wear a grounding wrist band when handling the boards. Do not touch the

boards unnecessarily.

Grounding

These instructions are intended for all who are responsible for the grounding of the

drive. Incorrect grounding can cause physical injury, death or equipment malfunction

and increase electromagnetic interference.

•Ground the drive, motor and adjoining equipment to ensure personnel safety in

all circumstances, and to reduce electromagnetic emission and pick-up.

•Make sure that grounding conductors are adequately sized as required by

safety regulations.

•In a multiple-drive installation, connect each drive separately to protective

earth (PE).

•ACS800-01: In European CE compliant installations and in other installations

where EMC emissions must be minimized, make a 360° high frequency

grounding of cable entries in order to suppress electromagnetic disturbances.

In addition, connect the cable shields to protective earth (PE) in order to meet

safety regulations.

ACS800-04 in first environment: make a 360° high frequency grounding of

cable entries at the cabinet lead-through.

(ACS800-02: 360° high frequency grounding of cable entries is not required at

the drive end.)

•Do not install a drive with EMC filter option +E202 or +E200 (available for

ACS800-01 only) on an ungrounded power system or a high resistance-

grounded (over 30 ohms) power system.

Note:

•Power cable shields are suitable for equipment grounding conductors only

when adequately sized to meet safety regulations.

•As the normal leakage current of the drive is higher than 3.5 mA AC or 10 mA

DC (stated by EN 50178, 5.2.11.1), a fixed protective earth connection is

required.

Safety instructions

Fibre optic cables

WARNING! Handle the fibre optic cables with care. When unplugging optic cables,

always grab the connector, not the cable itself. Do not touch the ends of the fibres

with bare hands as the fibre is extremely sensitive to dirt. The minimum allowed

bend radius is 35 mm (1.4 in.).

Mechanical installation

These notes are intended for all who install the drive. Handle the unit carefully to

avoid damage and injury.

•ACS800-01: The drive is heavy. Do not lift it alone. Do not lift the unit by the

front cover. Place the unit only on its back.

ACS800-02, ACS800-04: The drive is heavy. Lift the drive by the lifting lugs

only. Do not tilt the unit. The unit will overturn from a tilt of about 6 degrees.

•Make sure that dust from drilling does not enter the drive when installing.

Electrically conductive dust inside the unit may cause damage or lead to

malfunction.

•Ensure sufficient cooling.

•Do not fasten the drive by riveting or welding.

Safety instructions

Operation

These warnings are intended for all who plan the operation of the drive or operate

the drive. Ignoring the instructions can cause physical injury or death or damage the

equipment.

•Before adjusting the drive and putting it into service, make sure that the motor

and all driven equipment are suitable for operation throughout the speed range

provided by the drive. The drive can be adjusted to operate the motor at

speeds above and below the speed provided by connecting the motor directly

to the power line.

•Do not activate automatic fault reset functions of the Standard Application

Program if dangerous situations can occur. When activated, these functions

will reset the drive and resume operation after a fault.

•Do not control the motor with the disconnecting device (disconnecting means);

instead, use the control panel keys and , or commands via the I/O

board of the drive. The maximum allowed number of charging cycles of the DC

capacitors (i.e. power-ups by applying power) is five in ten minutes.

Note:

•If an external source for start command is selected and it is ON, the drive (with

Standard Application Program) will start immediately after fault reset unless the

drive is configured for 3-wire (a pulse) start/stop.

•When the control location is not set to Local (L not shown in the status row of

the display), the stop key on the control panel will not stop the drive. To stop

the drive using the control panel, press the LOC/REM key and then the stop

key .

Safety instructions

Permanent magnet motor

These are additional warnings concerning permanent magnet motor drives.

WARNING! Do not work on the drive when the permanent magnet motor is rotating.

Also, when the supply power is switched off and the inverter is stopped, a rotating

permanent magnet motor feeds power to the intermediate circuit of the drive and the

supply connections become live.

Installation and maintenance work

Before installation and maintenance work on the drive:

• Disconnect the motor from the drive with a safety switch

and additionally if possible (or)

• lock the motor shaft and ground the motor connection terminals temporarily by

connecting them together as well as to the PE. Before grounding, measure that

the motor is de-energizied.

Operation

Do not run the motor over the rated speed. Motor overspeed leads to overvoltage

which may explode the capacitors in the intermediate circuit of the drive.

This manual suits for next models

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide