ABB 6153 EB-500 User manual

ABB i-bus® EIB

Actuator 6153 EB-500

for lamp installation with

control output (0 - 10 V)

for electronic ballasts

Operating instructions

only for authorized, skilled electricians with

EIB training

73 - 1 - 5832

22013

Important instructions

Attention

It is absolutely essential that the EIB bus is installed

by an authorized electrician. Laying and connection of

bus line and applications devices must be effected in

conformity with valid regulations according to DIN -

VDE and the EIB manual of the ZVEI / ZVEH.

Connect the touch contact input to the same phase as

the device’s power supply.

For wiring of the actuator 6153 EB, the specifications

of the lamp / EVG manufacturer with regard to current

at make and power factor have to be observed.In some

cases it may be necessary to install a making current

limiter (e. g. 6515).

Notes

If the physical address has not yet been assigned, the

programming key (Fig.1, pos.5) should still be accessible.

If necessary, please install the lamp cover lateron. The

manufacturer database of Busch-Jaeger is continuously

updated. It stores the latest types of applications and their

related descriptions. If this database is not available to

you, please send for a copy.

Technical data / Connection

EIB connection

Nominal voltage: 24 V

Current consumption: < 10 mA

Switching connection

Nominal voltage: 230V - 50 Hz

Switching current: 10 A, cos ϕ0.6

Touch contact input: 230 V, 50 Hz

Line length of the touch

contact input: max. 100 m (unlighted)

Control voltage: 0 - 10 V

Control current: up to 50 mA

Operating temperature: -5 to +45 °C

Protection type: IP 20

←o switched phase (lamp)

→o phase (lamp)

L o phase (voltage supply)

N o neutral conductor

1 o touch contact input

+ o control voltage 0-10 V (EVG)

– o control voltage 0-10 V (EVG)

12 76453

+

–

Installation / Fig. 1

Switch off supply voltage !

Remove both outer caps from the device. The device is

fixed in the lamps by means of screws put through the

long holes (cf. Fig. 1 below, positions 1; 7 ).

The connection of supply voltage and control line is effected

at the 7-pin terminal block (pos. 2). Please observe the

connection information given in the „technical data“

section. When the bus voltage is missing, and a 230 V

voltage supplied, the actuator 6153 EB will auto-

matically switch on (working illumination).

The connection to the EIB bus is made by means of a 2-

pin bus terminal (item no. 6183) which is plugged into the

entrance (pos. 6). Please make sure that the polarity of

terminals is correct (red = +, grey = -).

Adapt bus coupling process

Assign physical address

• Connect a PC equipped with the EIBA software (ETS)

to the EIB bus line via an EIB-RS 232 interface.

• Press the programming key (pos. 5) at the actuator:

the red programming LED (pos. 4) will become

illuminated.

• After the physical address has been programmed,

the red LED will go out.

• Write the number of the physical address on the

device using a smudge-proof pencil (df. Fig. 1, pos. 3).

Assign group address(es)

• Group addresses are assigned via a PC in connection

with the ETS software.

Select application

Open the device window and choose the desired

application version. At present, there are two versions

available.

Adapt bus coupling process

Alternative application

Version 1

This device offers the following functions:

• Switching of lamps on-site via several conventional

touch contacts (e. g. 2020 US without lighting).

• Dimming of lamps with electronic ballasts (0-10 V

control input) via EIB sensors (e. g. 6118xx).

• Calling of two freely definable brightness values

(presets) for lamps with electronic ballasts (0 - 10 V

control input)

- via EIB sensors (e. g. 6117xx).

You may differentiate this version of the actuator 6153 EB

by using the „parameters“ option of your ETS software:

• ON:

- last brightness setting (memory) or

- minimum brightness (basic brightness) or

- maximum brightness

• Dimming speed

- time for one run of the light (0 -100 %) in seconds.

• Preset 1 or 2, resp.

- these values are freely selectable via percentage

inputs.

Adapt bus coupling process

Version 2

This device may be used as a pure switching actuator.

Then, its contact time behavior may be adjusted via the

„parameters“ option (e. g. staircase lighting time-switch).

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M

3M MicroTouch EX113 reference guide