4iiii Podiiiium User manual
Manual
User
1. Introduction
1.1 What’s in the box 1
2. Getting Started
2.1 Installation 2
2.2 Preparing for your ride 3
2.3 Charging and caring for your batteries 4
2.3.1 Non-drive-side powermeters 5
2.3.2 Drive-side powermeters for Shimano FC-R8000 and FC-R9100 6
2.4 Conguring your powermeter using the 4iiii App 7
2.4.1 Conguring as a dual-sided powermeter 8
2.4.2 Unlinking your dual-sided powermeter 9
2.4.3 Conguring in single-sided mode 10
3. Pairing
3.1. Pairing with ANT+ enabled displays 11
3.2. Pairing with Bluetooth® 13
TABLE OF CONTENTS
4. Performing a Zero Oset
4.1. Performing a zero oset via ANT+ 14
4.2. Performing a zero oset using your 4iiii App (Bluetooth®) 16
5. Advanced Features
5.1 Renaming your powermeter using the 4iiii App 18
5.2 Setting scale factor compensation values 19
5.3 Using third-party compatibility mode on Bluetooth® 20
6. Maintenance and Care 21
7. Troubleshooting 22
8. Specications 25
9. Safety Information 26
10.Warranty 27
11. Regulatory Compliance 30
12. Contact Information Back Cover
TABLE OF CONTENTS
Podiiiium
Crankset
included
with Ride
Ready
purchase
3m dual-ended 90 degree
micro-USB cable.
Extra dust cap and
dust-cap screw.
1INTRODUCTION
1.1 What’s in the Box?
Your Podiiiium
powermeter comes
complete with the
following:
1
Table of Contents
2.1 Installation
The steps and tools needed for installing a crankset on your bike will vary
depending on the model of your crankset. For your safety, follow the crankset
manufacturer’s instructions when installing the crankset to your bike. Consult your
local bike mechanic if you are not comfortable or able to follow the manufacturer’s
installation instructions.
Quick Tip: Accuracy of your powermeter is dependent on proper torque. Not following
proper installation procedure could aect the accuracy of your powermeter.
2GETTING STARTED
2
Table of Contents
2.2 Preparing for your ride
1. Wake your Podiiiium from shipping mode by plugging into a power source for at
least 5 seconds. Unplug the charging cord when charge is complete.
2. Your Podiiiium powermeter is equipped with an indicator LED.
During charging, the LED will turn red. Once the powermeter
is fully charged, the LED will turn green for a few minutes and
then turn o.
2GETTING STARTED
75-100%
LED displays green for
3 seconds (long ash)
25-50%
LED shows
1 long red ash
50-75%
LED blinks green
5 times (short ashes)
0-25%
LED shows
5 short red ashes
3. Once charged, wake-up Podiiiium by rotating the crank 3 or 4 times.
4. Pair with your power capable device.
5. Zero Podiiiium using your paired device. Unclip from
your pedals and position crankarms as shown.
Press “zero oset” or “calibrate” on your display.
LED ashes blue once to indicate successful zero oset. Left
Crank
Right
Crank
3
Table of Contents
2.3 Charging and caring for your batteries
Your powermeter uses a rechargeable lithium ion batteries. When the reported battery
life is 8%, you will have 4-5 hours of remaining usage.
Your dual-sided Podiiiium Pro PRECISION Powermeter comes with a micro-USB charge
cable that allows you to charge both sides at once.
Your power meter will take approximately 3-4 hours to fully charge.
Please note that the charge time may depend on the power source used.
NOTE: If the battery reaches 0% on one side, the other side of the dual system will
automatically operate as a single-sided powermeter; reported wattage from this side
will be doubled.
• Use a USB AC adapter with a voltage of 5.0V and with a current equal or greater
than 1.0A.
• Use the designated charge cable to charge the powermeter.
• Avoid contact of the charge cable and/ or powermeter with water while charging.
• Do not disassemble or modify the charge cable.
• Charge the device at the specied power supply voltage only.
• Lithium-ion batteries are recyclable. For information on disposal of used batteries,
contact your original dealer.
• If the battery has become completely depleted, charge it as soon as possible.
Leaving the battery in a depleted state can cause the battery to deteriorate.
2GETTING STARTED
4
Table of Contents
2GETTING STARTED
2.3.1 Non-drive-side powermeters
To charge your non-drive side powermeter, connect the 90-degree micro-USB
connector to the powermeter. Ensure cable is connected as per image below:
5
Table of Contents
2GETTING STARTED
2.3.2 Drive-side powermeters for Shimano Cranksets
To charge your drive side powermeter, slip the 90-degree micro-USB connector
between the crank-arm and chain-rings. Ensure cable is connected as per image below:
6
Table of Contents
2GETTING STARTED
2.4 Conguring your powermeter using the 4iiii App
When your Podiiiium was shipped from the factory, the drive side and non-drive side
powermeters were linked together such that they operate as a dual-sided powermeter.
Your powermeter can also operate as two independent single-sided powermeters. If
you want to operate your Podiiiium powermeter as a single-sided powermeter using
only one crank arm, follow the instructions in Section 2.4.2
Additional information and settings on your Podiiiium can be accessed through the
4iiii app on iOS and Android devices using Bluetooth®.
To congure your Podiiiium powermeter in single-sided mode, follow the instructions
in Section 2.4.3
To congure your Podiiiium powermeter in dual-sided mode, follow the instructions in
Section 2.4.1
Quick Tips:
Pairing is the connection between your powermeter and display units
such as a bike computer, watch, or smartphone. Linking is the connection between the
drive and non-drive side powermeters.
Connect your powermeter to the 4iiii App once a month to check for the latest rmware
update. If your rmware requires updating, you will be prompted to upgrade.
Your battery percentage for you drive-side and non-drive-side powermeter can be
viewed by connecting to the 4iiii App.
7
Table of Contents
Table of contents
Other 4iiii Measuring Instrument manuals
