Wilson Electronics Weboost DRIVE REACH User manual

Installation Guide

Vehicle Signal Booster Kit

DRIVE REACH

A WILSON ELECTRONICS BRAND

NEED HELP? support.weboost.com 866.294.1660

ENGLISHESPAÑOL

ENGLISH

______

Index

Package Contents 1

STEP 1: Mount Outside Magnetic Antenna 2

STEP 2: Mount Inside Antenna 4

STEP 3: Connect Coax Cables To Booster 5

STEP 4: Connect Power Supply To Booster 6

STEP 5: Plug Power Adapter Into Vehicle’s Power Supply 7

Booster Light Patterns 8

Troubleshooting 9

Speciﬁcations 11

Warranty 12

ENGLISH

DRIVE REACH VEHICLE SIGNAL BOOSTER 1

________

Package

Contents

Booster

& Bracket

Outside

Antenna

Inside

Antenna

Power

Supply

Optional: Adhesive disk for aluminum vehicles

ENGLISH

2VEHICLE SIGNAL BOOSTER DRIVE REACH

______

Step 1: Mount Outside

Magnetic Antenna

WORKS WITH ALL VEHICLES

Identify a location on the top of your vehicle that is:

 Near the center of the roof

 At least 12 inches away from any other antennas

 At least 12 inches away from any windows

(including sunroofs)

Clean the surface where you will place the outside

antenna.

Mount the outside antenna by placing on top of vehicle.

12 in. away from windows

(including sunroofs)

NOTE: For aluminum roofs, an adhesive disk is included to mount the

outside antenna (do not use if outside antenna will magnetize to the top of

your vehicle).

ENGLISH

DRIVE REACH VEHICLE SIGNAL BOOSTER 3

NOTE: When going through a car wash,

remember to remove your antenna.

NOTE: The cable is strong enough that it

may be routed under weather stripping

and shut in most vehicle doors without

damaging the cable.

Car/Sedan: Cable routed

into rear side door.

SUV/Van/Hatchback: Cable

routed into top of hatchback door.

Truck: Cable routed into

side door.

______

(STEP 1 cont.)

See options below on how cable can be routed with

different vehicles.

ENGLISH

4VEHICLE SIGNAL BOOSTER DRIVE REACH

______

Step 2: Mount Inside Antenna

Identify a place to mount the In-Vehicle Antenna, either on the

side of the seat or on the dash and mount. The location should

be at least 18 inches but no more than 36 inches from where

the cellular device will be used. Use the Velcro® adhesive strip

or the 2-sided adhesive strip provided and attach to the side

of the antenna labeled “MOUNTING SIDE”. Then mount to

desired location.

In-Vehicle Antenna

Dash Mount

Velcro® strip

In-Vehicle Antenna

Seat Mount

WARNING: DO NOT MOUNT WHERE AIRBAGS WILL DEPLOY.

ENGLISH

DRIVE REACH VEHICLE SIGNAL BOOSTER 5

______

Step 3: Connect Coax Cables

To Booster

Connect the cable from the Outside Antenna to the port

labeled “Outside Antenna” on the Drive Reach booster.

Connect the cable from the In-Vehicle Antenna to the port

labeled “Inside Antenna” on the booster.

from Outside Antenna

from Inside Antenna

NOTE: Bracket can be used to fasten booster in a speciﬁc location if desired.

The Velcro® strip on the bottom of the bracket can also be used to keep

booster from sliding around.

bracket

Drive Reach

ENGLISH

6VEHICLE SIGNAL BOOSTER DRIVE REACH

______

Step 4: Connect Power

Supply To Booster

Connect the power supply cord to the end of the booster,

labeled “ .”

NOTE: Do NOT connect the power to the Signal Booster until you have

connected both the Inside and Outside Antennas.

Power Supply

from Outside Antenna

from Inside Antenna

ENGLISH

DRIVE REACH VEHICLE SIGNAL BOOSTER 7

______

Step 5: Plug Power Adapter

Into Vehicle’s Power Supply

Plug the power adapter into vehicle’s 12V DC power supply.

The Drive Reach will automatically power on when plugged in.

If your Drive Reach is working correctly, the light on the power

adapter will be red, and the light on the booster will be green.

Use only the power supply provided in this package.

NOTE: If the 12V Cigarette Lighter port on your car is always on (even when

your vehicle is turned o) and you will be parking for extended periods of

time (more than a day), we recommend you turn the booster o by pushing

the LED light, which is also a button. This will prevent the Drive Reach from

draining the battery in your vehicle.

DC Power Adapter

NEED HELP? support.weboost.com 866.294.1660

ENGLISH

8VEHICLE SIGNAL BOOSTER DRIVE REACH

______

Booster Light Patterns

NEED HELP? support.weboost.com 866.294.1660

Solid Green

This indicates that your booster is functioning properly and there are no issues with

installation.

Blinking Red, Then Solid Green

This indicates that one or more of the booster bands has reduced power due

to a minor feedback loop condition called oscillation. This is a built in safety

feature to prevent harmful interference with a nearby cell tower. If you are already

experiencing the desired signal boost, then no further adjustments are necessary.

If you are not experiencing the desired boost in coverage then refer to the

Troubleshooting section.

Solid Red

This is due to a major oscillation (feedback) loop. This is a built in safety feature

that causes a band to shut off to prevent harmful interference with a nearby cell

tower. Refer to Troubleshooting section.

Light O

If the Drive Reach Signal Booster’s light is off, verify your power supply has power.

NOTE: The Signal Booster can be reset by disconnecting and reconnecting

the power supply.

After troubleshooting you must initiate a new power cycle by disconnecting and

then reconnecting power to the Booster.

Table of contents

Languages:

Other Wilson Electronics Extender manuals

Wilson Electronics

Wilson Electronics weBoost DRIVE X RV User manual

Wilson Electronics

Wilson Electronics SLEEK 2B5225 User manual

Wilson Electronics

Wilson Electronics AG Pro Quint 461104 User manual

Wilson Electronics

Wilson Electronics weBoost DRIVE X 475021R User manual

Wilson Electronics

Wilson Electronics signalboost dt 271265 User manual

Wilson Electronics

Wilson Electronics 801101 User manual

Wilson Electronics

Wilson Electronics WILSON PRO 1050 User manual

Wilson Electronics

Wilson Electronics Pro 70 Plus User manual

Wilson Electronics

Wilson Electronics WEBOOST DRIVE X OTR User manual

Wilson Electronics

Wilson Electronics 801213 User manual

Wilson Electronics

Wilson Electronics weboost Drive Reach OTR Installation guide

Wilson Electronics

Wilson Electronics SLEEK 2B5225 User manual

Wilson Electronics

Wilson Electronics Tri-Band 4G-C User manual

Wilson Electronics

Wilson Electronics weboost AH100-PRO User manual

Wilson Electronics

Wilson Electronics 460054 User manual

Wilson Electronics

Wilson Electronics weBoost DRIVE 4G-X OTR 470210R User manual

Wilson Electronics

Wilson Electronics Sleek 4G User manual

Wilson Electronics

Wilson Electronics weboost Home Complete User manual

Wilson Electronics

Wilson Electronics 271201 User manual

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 User manual

Wilson Electronics

Wilson Electronics PRO Series User manual

Wilson Electronics

Wilson Electronics Signal 4G SmarTech III User manual

Wilson Electronics

Wilson Electronics weboost Office 100 User manual

Wilson Electronics

Wilson Electronics PRO 1100 User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual

Wilson Electronics weboost DRIVE REACH User manual

Popular Extender manuals by other brands