Volt VDL-6000 User manual
INSTALLATION INSTRUCTIONS
VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
VOLT® Cast Brass Deck Light
ITEM: VDL-600 & VDL-6000
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
VOLT® Cast Brass Deck Light VDL-600 & VDL-6000
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
2
This luminaire is intended for installation in accordance with local codes and the National
Electric Code (NEC). Failure to adhere to these codes and instructions may result in
serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from
pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated
maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable for outdoor
use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches
(15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches (152
mm).
7. If additional lengths of low voltage cable are required, please contact www.
voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
PACKAGE CONTENTS
3
A. (1) Luminaire
B. (2) Lock Screws
Product Dimensions
2”
2 1/4”
3 3/8”
Pro Technique for Hiding Lead Wire
Determine the location for the xture. Drill a hole straight
through the desired mounting location and run the lead wire
out the backside of the location so that the wires are not visible
from the front side. Use a matching trim piece and cut a groove
in the back of trim. Cover the lead wires with the matching trim
piece.
Pro Technique for Hiding Splice Connections
All xtures come with 4’ of lead wire enabling you to hide the
splice connections out of sight. If you must make a splice
connection in view, use an inline heat shrink style connection that
is less visible than traditional twist caps.
1
2
VOLT® Cast Brass Deck Light VDL-600 & VDL-6000
INSTALLATION INSTRUCTIONS
4
Remove Lens Assembly
Rotate the lens assembly counter
clockwise until it is stops and then
lift the lens assembly straight off.
Note: The rst time it may be
difcult because the luminaire has
a tight o-ring seal and a grease
sealant for moisture protection.
Base
Lens Assembly
Luminaire
Install Base
Attach the base onto the desired
location and secure with the lock
screws.
Note: Wall anchors are required
for certain installation conditions
e.g. Brick wall, Concrete Wall, etc.).
Mark on the wall for wall anchors
from the holes on the base.
Remove the base and drill proper
holes on the wall and then insert
the wall anchors.
Wall Anchor
Lock
Screw
Base
3
Wire Connections
Strip both leads from the luminaire
pigtail. Using two wire connectors
(sold separately), connect the leads
from the luminaire to the main supply
cable leads.
Luminaire
Main Supply Cable
Pigtail
Wire Connector
4
5
5
Install Bulb
Insert the bulb with correct wattage and
type marked on the luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Bulb
Socket
Install Lens Assembly
Push the lens assembly back onto the
base aligned with the gaps on the base.
Push hard (moisture proof xture requires
force to get air out). Once the lens
assembly is ush with the base, rotate the
lens assembly until it stops and locks into
place.
Gap
Inner Shield
Install/Replace Bulb
Rotate the lens assembly and then remove it to expose the bulb and replace
it with the correct wattage and type marked on the luminaire label. And then
reinstall the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture and dust at all
times. Always reinstall lens assembly when moved.
Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
This manual suits for next models
2
Table of contents
Other Volt Landscape Lighting manuals
Volt
Volt VPL-1044-4-BBZ User manual
Volt
Volt VPL-1041-4-BBZ User manual
Volt
Volt Top Dog Scotty VAL-1183 User manual
Volt
Volt VHS-6719-25-BBZ User manual
Volt
Volt 2-in-1 Tiki-Brass Torch Light User manual
Volt
Volt VUL-6804-25-BBZ User manual
Volt
Volt STK-17LI Series User manual
Volt
Volt VFL-4027 User manual
Volt
Volt VDL-6009-4-BBZ User manual
Volt
Volt 3601 Series User manual
Volt
Volt VHS-6719-BBZ User manual
Volt
Volt VAC-STK-PWR-PGR User manual
Volt
Volt VPL-1019-26-4-BBZ User manual
Volt
Volt VSPL-1045-BBZ User manual
Volt
Volt VHS-668-4-BBZ User manual
Volt
Volt VHS-67 Series User manual
Volt
Volt All Star Mini Twinnovator User manual
Volt
Volt 310 Series User manual
Volt
Volt ShadowMaster VPL-1039 User manual
Volt
Volt VAC-AL-GGT1-BBZ User manual
Popular Landscape Lighting manuals by other brands
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Specification sheet
Cooper Lighting
Cooper Lighting Invue 42 - 175W Specification sheet
Saxby Lighting
Saxby Lighting Islay 68784 Instruction leaflet
LIGMAN
LIGMAN EU-10016-3 installation manual
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza specification
LIGMAN
LIGMAN KI-60475 installation manual
