Vivo STAND-V012K User manual

Pneumatic Arm Dual Monitor Extra Tall Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v012k

SKU: STAND-V012K

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x2)

Arm

B(x1)

Clamp

C(x2)

VESA Plate

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

D(x1)

Top Pole

E(x1)

Bottom Pole

F (x1)

Pole Cap

G(x1)

Pole Connector

H (x2)

Cable Clip

S-A (x2)

M6x10

Thumbscrew

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

M-A (x8)

M4x12 Screw

M-B (x8)

M4x16 Screw

M-C (x8)

M5x12 Screw

M-D (x8)

M5x16 Screw

M-E (x8)

D5 Washer

M-F (x8)

Spacer

S-B (x3)

M6x16 Screw

I(x1)

Grommet Base

J(x1)

Support Plate

M (x1)

So Pad

T-A (x1)

3mm Allen

Wrench

T-B (x1)

4mm Allen

Wrench

T-C (x1)

6mm Allen

Wrench

ASSEMBLY STEPS

TOOLS NEEDED

2.2-19.8lbs

(1-9kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

STEP 1

PER MONITOR

Insert Pole Cap (F) into the top of Top Pole (D).

STEP 2

Loosen the screws and disassemble the Clamp (B) and seperate into Clamp Brace (B1) and Clamp

(B2) using 4mm Allen Wrench (T-B).

T-B

STEP 3

OPTION A: Clamp Installation

Attach Clamp Brace (B1) to Bottom Pole (E)

using the M6x16 Screws (S-B) and the 4mm

Allen Wrench (T-B). Peel the protective film o

of So Pad (M) and place it onto Clamp Brace

(B1). For thinner desktops, re-attach the Clamp

(B2) to the Clamp Brace (B1) and tighten the

screws using the 4mm Allen Wrench (T-B).

For thicker desktops, disassemble Clamp (B2)

using a Phillips screwdriver as shown in 3.1.

Flip the L-bracket over and reassemble. Then

re-attach Clamp (B2) to Clamp Brace (B1) and

tighten the screws using the 4mm Allen Wrench

(T-B).

OPTION B: Grommet Installation

For grommet hole attachment only, cut So Pad (M)

along the indentations. Peel the protective film o

of So Pad (M) and place the pieces onto Grommet

Base (I) as shown below. If not using an existing

through-hole, using a 10mm (⅜”) drill bit, drill

through the desktop at least 2” away from the edge.

Disassemble Clamp (B2) using a Philips screwdriver.

Set aside all parts except for Clamp Bolt (B3).

Attach Bottom Pole (E) and Grommet Base (I) to the

desktop using Support Plate (J) and Clamp Bolt (B3)

as shown below.

T-B

S-B

T-B

STEP 6

Attach VESA Plates (C) to the back of the monitors using Screws (M-A through M-D) and

Washers (M-E). If needed, use Spacers (M-F).

Slide Cable Clip (H) and Arm (A) onto Bottom Pole (E).

Tighten Arm (A) using 6mm Allen Wrench (T-C).

STEP 4

Attach Top Pole (D) to Bottom Pole (E) using Pole Connector (G). Once poles are fully threaded on,

tighten set screws on Pole Connector (G) using 3mm Allen Wrench (T-A). Slide Cable Clip (H) and Arm

(A) onto Top Pole (D). Tighten Arm (A) using 6mm Allen Wrench (T-C).

STEP 5

T-C

T-A A

T-C

STEP 8

Adjust gas spring support in Arms (A) using 6mm Allen wrench (T-C). Turning counter-clockwise

increases support, and clockwise decreases.

T-C

STEP 7

Slide VESA Plates (C) with monitors

over the brackets on Arms (A). Secure

using M6x10 Thumbscrews (S-A).

STEP 9

Remove cable management covers

from underneath Arms (A).

S-A

T-C A

STEP 9 (Continued)

Manage cables by reattching the cable management covers to Arm (A) and Cable Clips (H).

STEP 10

Adjust tilt support using 6mm Allen Wrench (T-C).

T-C

LAST UPDATED: 11/11/2021

REV1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 