Vivo MOUNT-UVM01 User manual

Universal VESA Adapter Bracket Kit

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/mount-uvm01

SKU: MOUNT-UVM01

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

22lbs

(10kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING!

A (x2)

Upper Vertical

Bracket

B(x2)

Lower Vertical

Bracket

C(x2)

Upper Support

Bracket

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: SOME HARDWARE MAY NOT BE USED

D(x2)

Lower Support

Bracket

E (x4)

M5x45

Thumbscrew

F (x4)

Compression

Pad

G (x1)

Main Plate

H(x1)

VESA Plate

I(x1)

M6x10mm

Thumbscrew

J(x4)

M4x12

K (x4)

Washer

L (x4)

M5x6

M (x4)

M5x8 Flat

Head

N (x2)

M5x15

O(x2)

M5x16 Carriage

Bolt

P(x2)

M5 Nut

Q (x2)

M5x65

R (x1)

Wrench

S (x4)

Adhesive Pad

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

TOOLS NEEDED

Phillips

Screwdriver

Pencil SUPPORTED MONITOR RANGES :

most 20” - 32” screens

VESA Compatability :

100x100mm

Scissors

ASSEMBLY STEPS

STEP 1

Place monitor face down on a flat surface with bottom of monitor facing towards

you. Install power, video and other cables to monitor to assist in determining

needed clearance.

PART A: Preparation

STEP 2

Align bottom of one lower vertical bracket (B) with bottom edge of monitor. Locate hangers

closest to centerline of monitor, then mark the next hanger above center with a pencil.

Mark same hangers on the other lower vertical bracket.

Mark hanger set above center

Monitor Center

✓X ✓X

Buttons

Mark Mark

Ports

STEP 3

Hold the main plate (G) to center of back of monitor. Locate and mark entire region on

each side that does not overlap with any buttons or ports.

NOTE: Please be sure to also check for buttons on the bottom edge of the monitor!

✓X ✓X

Buttons

Mark Mark

Ports

STEP 4

Hold an adhesive pad (S) to the bottom edge of the monitor and trim length of pad to

match monitor. Trim remaining pads to the same length, and apply to inner faces of upper

and lower support brackets (C, D) towards the front.

STEP 1

Slide marked hangers on lower vertical brackets (B) onto the marked slotted region of the

main plate (G). Brackets should be an equal distance from the center if possible. If needed,

move the main plate up or down to clear ports on the monitor.

PART B: Lower Bracket Assembly

C + D

B B

STEP 2

Secure the main plate to the brackets using M5x15mm screws (N). If main plate is located

at the highest position, instead use M6x16mm carriage bolts (O) with M5 nuts (P) and

tighten with the wrench (R).

STEP 1 (Continued)

Move the main plate (G) up or down to avoid ports as necessary.

Ports

STEP 1

Place lip of one lower support bracket (D) under monitor edge where it will be installed.

Align lower vertical bracket (B) with first available hole in support bracket above monitor

and insert M5x8mm flat head screw (M). Attach other lower support bracket at same

location to opposite vertical bracket. Do not yet tighten screws. Please note, lower support

brackets have slightly longer lip than upper support brackets.

PART C: Upper Bracket Assembly

Move bracket assembly as close

to monitor as possible.

Hold D against monitor face.

Move bracket assembly as close

to monitor as possible.

STEP 2

Attach upper support brackets (C) to upper vertical brackets (A) using M5x8mm flat head

screws (M) at same hole positions as lower support brackets. Do not yet tighten screws.

STEP 1

Partially slide upper vertical brackets (A) into lower vertical brackets (B).

PART D: Assemble Brackets to Monitor

STEP 2

STEP 3

Partially insert M5x45mm thumbscrews (E) into vertical brackets at positions closest to top

and bottom of the monitor where a flat surface is available. Place compression pads (F)

onto ends of thumbscrews, and turn screws until light force is applied to the back of the

monitor. If the monitor is much slimmer on top than at the bottom, instead use M5x65mm

screws for the top two holes. For curved monitors, turn screws evenly to slowly li bracket

assembly into position until assembly fits snug to the monitor.

WARNING! Excessive tightening of upper compression screws on ultraslim monitors

can damage your screen!

For best results, tighten lower compression screws until the mount feels secure and cannot

move relative to your monitor. Then tighten upper compression screws until they just

barely touch the back of your monitor. If mounting your monitor vertically, you can tighten

upper compression screws until the pad cannot slide along the monitor back.

Position assembly on the back of the monitor. Slide upper brackets down, making sure

the upper and lower support brackets are fully engaged with the monitor. Insert M5x6mm

screws (L) into back of vertical brackets and tighten to secure brackets.

All support bracket lips under

monitor edge.

STEP 3 (Continued)

STEP 4

Making sure upper and lower support brackets are correctly aligned

and holding monitor, tighten M5x8 flat head screws (M) with a Phillips

screwdriver.

Tighten screws M

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 