Vicon SN688D-WIR User manual
SN688D-WIR Outdoor PTZ Dome Camera
Quick Guide
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform precisely
as described in the documentation. This system has not been designed to be used in life-
critical situations and must not be used for this purpose.
Document Number: 8009-8270-30-00 Product specifications subject to change without
notice. Issued: 1/19 Copyright © 2019 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: 631-952-2288) Fax: 631-951-2288
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266) UK: 44/(0) 1489-566300
www.vicon-security.com
XX270-30-00
2
1 Introduction
The SN688D network camera is designed for performance in the most demanding security
installations. The 4K/8 MP camera has an integral 30X optical zoom lens and integrated IR LEDs.
The camera provides quad-streaming video and supports H.265/H.264 compression technology,
drastically reducing file sizes and conserving valuable network bandwidth; M-JPEG compression is
also supported. By using its dedicated program, multiple users are able to have access to the
network camera simultaneously, or a single user can monitor various network cameras at the same
time. It also enables users to play, store and retrieve a monitoring image by using a PC. All the
settings and real time monitoring screens are provided through access to the web.
1.1 Components
This system comes with the following components;
* Dome Camera 1
* Installation Guide 1
* 2P screw type Connector 1
* 5P screw type Connector 1
* PoE Injector 1
* RJ-45 Waterproof Cover 1
* Install Adaptor 1
NOTE: Check your package to make sure that you received the complete system, including all
components listed above.
NOTE: Adaptor for 12 VDC is not supplied.
3
1.2 Key Features
• Brilliant video quality
The network camera offers the highly efficient H.264/H.265 video compression, which drastically
reduces bandwidth and storage requirements without compromising image quality. Motion JPEG
is also supported for increased flexibility.
• Quad Streams
The network camera can deliver quad video streams simultaneously using H.264/H.265 and
Motion JPEG. This means that several video streams can be configured with different
compression formats, resolutions and frame rates for different needs.
• Intelligent video capabilities
The network camera includes intelligent capabilities such as enhanced video motion detection.
The network camera’s external inputs and outputs can be connected to devices such as sensors
and relays, enabling the system to react to alarms and activate lights or open/close doors.
• Improved Security
The network camera logs all user access, and lists currently connected users. Also, its full frame
rate video can be provided over HTTPS.
• ONVIF Certificate
This is a global interface standard that makes it easier for end users, integrators, consultants,
and manufacturers to take advantage of the possibilities offered by network video technology.
ONVIF enables interoperability between different vendor products, increased flexibility, reduced
cost, and future-proof systems.
• Micro-SD Recording support
The network camera also supports a Micro-SD memory slot for local recording with removable
storage of type SDHC and SDXC.
• Audio support
The network camera also supports two-way audio.
• Built-in Synchronized IR LED & Fixed IR LED
The camera is equipped with two built-in IR LEDs, fixed one for wide view and zoom
synchronized adjustable one for distant view.
4
2 Installation
2.1 Mounting the Camera
An optional mount kit, either a wall mount or the ceiling mount, it required for installation.
The wall or ceiling mount must be attached to a structural object such as hard wood, concrete that
will support the weight of the mount and dome camera.
The use of a solid backboard is recommended when attaching to gypsum walls.
1. Remove the Protection pad and the tape from attached the dome camera.
2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic bushing. (For
ceiling mounting use the supplied M6 tapping screw and bushing.)
3. To seal tightly, wrap the thread of the pipe end with Teflon tape about 20 times for sealing. Then
use a silicone rubber sealant to seal the area where the wall (ceiling) mount and the pipe meet.
4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange, press it to
the surface and line up the flange hole with drilled holes.
CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
CAUTION 2: When installing, a mounting bracket must be used.
CAUTION 3: Please reset the camera after 30 ~ 60 minutes when installing it in situations
colder than 14° F (-10°C).
5
2.1.1 Wall Mounting
The wall mounting plate must be attached to a structural object such as concrete that will support
the weight of the mount and dome camera.
1. Select a suitable mounting location and verify there is sufficient cable to reach the middle of
the Wall Mount.
2. Mark and drill mounting holes in the surface using the Wall Mount Flange as a template.
3. Secure the mounting plate to the wall using the hardware provided or appropriate for the
mounting surface.
4. Pull out cables required to connect to the dome camera from the wall or route cables through
a section of 0.75 in (19 mm) conduit pipe.
5. Remove the cable access plate from the underside of the wall mount bracket.
6. Attach wall mount bracket using plastic anchors and 8x35 screws; route cables through the
access plate hole.
7. Attach the 1.5 inch adapter to wall mount bracket and fix it using set screw.
8. Attach the camera’s safety wire to the wall mount’s latch.
9. Route cables on the dome through the wall mount bracket. Fix the housing to the wall mount
bracket using the locking nut and tighten the housing set screw with the supplied wrench.
10. Reattach the access plate.
11. Push in and turn the camera clockwise into the adapter and fix it using set screw of the
adapter.
6
2.1.2 Ceiling Mounting
The ceiling mounting plate must be attached to a structural object such as concrete that will support
the weight of the mount and dome camera.
1. Select a suitable mounting location
and verify there is sufficient cable
to connect with cables from the
housing.
2. Mark and drill mounting holes on
the surface using the ceiling mount
flange as a template.
3. Secure the mounting plate to the
wall using the hardware provided
or appropriate for the mounting
surface.
4. Pull out cables required to connect
to the dome camera from the
ceiling.
5. Attach the ceiling mount plater
using plastic anchors and screws;
route cables through the locking
nut.
6. Attach 1.5 inch adapter to the pipe
and fix it using set screw of the
adapter.
7. Route cables through the pipe.
Tighten the housing with the pipe
using the socket.
8. Attach safety wire to the ceiling
mount’s M6x35 tapping screw.
9. After connecting cables, fix the
pipe to the ceiling mount using the
locking nut.
10. Tighten set screws of the socket
and locking nut with the supplied
wrench.
7
2.2 Basic Configuration of Camera System
No.
Connector
Wire Color
Description
1
Power jack
BLACK
CAMERA POWER
(12 VDC)
2
RJ-45
BLACK
Ethernet, RJ-45 port compatible with
10/100Mbps
3
RCA jack
BLACK
AUDIO INPUT
4
RCA jack
GRAY
AUDIO OUTPUT
5
5-pin cable
YELLOW
ALARM INPUT 1
WHITE
ALARM INPUT 2
VIOLET
ALARM INPUT 3
BROWN
ALARM INPUT 4
GRAY
GND
6
2-pin cable
RED
ALARM OUTPUT
BLACK
GND
The camera must be installed by qualified service personnel in accordance with all local and federal
electrical and building codes.
8
2.3 Resetting to the factory default settings
To reset the network camera to the original factory settings, go to the Setup > System > Maintenance
web page (described in “System > Maintenance” of User Manual) or use the Reset button on the
network camera, as described below:
• Using the Reset button:
Follow the instructions below to reset the network camera to the factory default settings using the
Reset button.
1. Switch off the network camera by disconnecting the power adapter.
2. Open the Micro-SD card cover.
3. Press and hold the Reset button on the board with your finger while reconnecting the power.
4. Keep the Reset button pressed for about 2 seconds.
5. Release the Reset button.
6. The network camera resets to factory defaults and restarts after completing the factory reset.
7. Close the Micro-SD card cover tightly to ensure waterproofing.
CAUTION: When performing a Factory Reset, you will lose any settings that have been saved.
9
2.4 Connections
• Micro-SD Card Insertion
User can install and change Micro-SD card as shown in the following picture.
1. Open the Micro-SD card cover.
2. Install or change Micro-SD card.
3. Close the Micro-SD card cover tightly to ensure waterproofing.
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the camera. Generally a crossover cable
is used for directly connection to PC, while a direct cable is used for connection to a hub.
• Connecting Alarms
– A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4)
You can use external devices to signal the camera to react on events. Mechanical or electrical
switches can be wired to the A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4) and G (Ground)
connectors.
– G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
– AO (Alarm Output)
The camera can activate external devices such as buzzers or lights. Connect the device to
the AO (Alarm Output) and G (Ground) connectors.
• Connecting Audio
Connect speaker to audio output line and external mic to audio input line.
10
• Connecting the Power
Connect 12 VDC power for the camera.
When using a 12 VDC adapter, connect the positive (+) pole to the “+” position and the
negative (-) pole to the “-” position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.
– Be careful not to reverse the polarity when you connect the power cable.
– You can also use a router featuring PoE (Power over Ethernet) to supply power to the
camera. If you use PoE to supply power to the camera, you must use the PoE (Power
over Ethernet) injector provided by the manufacturer for proper operation.
Other manuals for SN688D-WIR
1
Table of contents
Other Vicon Security Camera manuals
Vicon
Vicon SN688D-WIR User manual
Vicon
Vicon Roughneck AI V2008B-W310LPR User manual
Vicon
Vicon V682-PTZ User manual
Vicon
Vicon V3FCD SERIES User manual
Vicon
Vicon V930D User manual
Vicon
Vicon V15CCM-IR-2 Series Rouchneck User manual
Vicon
Vicon CE202D-WN User manual
Vicon
Vicon I-ONYX VND-970IP User manual
Vicon
Vicon V1020-WIR-180 User manual
Vicon
Vicon ALU-2500/230 Service manual
Vicon
Vicon VC275-24 User guide
Vicon
Vicon V700W Series User manual
Vicon
Vicon V992D-N4 Instruction manual
Vicon
Vicon CE202D-WN User manual
Vicon
Vicon Surveyor MKII Series XX282-40-01 Quick guide
Vicon
Vicon V2008-W0950-LPR User manual
Vicon
Vicon V960D-W Series Instruction manual
Vicon
Vicon V800D User manual
Vicon
Vicon V662-D-2 Operating instructions
Vicon
Vicon XX152-10-01 Installation instructions
