Vicon IX 4000 L User manual

Installation&

eration Manual

IX 4000 L, IX 4000 H

Colour Camera

Vicon Industries Inc. Does not warrant that the functions contained in this equipment will meet your requirments or

that the operation will be entirely error free or perform precisely as discribed in the documentation. This system has

not been designed to be used in life critical situations and must not be used for this purpose.

Product specifications subject to change without notice.

Vicon and ist logo are registered trademarks of Vicon Industries Inc.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24- Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 WEB: vicon-cctv.com

-2-

Dear Customer!

By selecting this VICON product you have chosen a professional device which

guarantees highest possible quality and reliability. We like to thank you very much for

your confidence in our products and kindly ask you to read the following instructions

carefully before commissioning the product in order to be able to take full advantage

of all quality features regarding this product line.

Contents Page

General Information

¨Safety Precautions 3

¨Accessories and Additional Devices 3

Mounting the Camera

¨Mounting the Camera to a Wall Mount 4

Commissioning the Camera

¨Tips for Camera Location 5

¨Adjustment of Back Focus 6

¨Calibration of ES/DC- Lenses 6

¨Focusing the Camera Lens 7

¨Circuit points and operation 8

¨Remote Jack 9

¨Camera Configuration 10

Exhibit

¨Troubleshooting 16

¨Technical Specifications 17

¨Cleaning and Care 18

¨Technical Support 18

¨Shipping Instructions 19

GENERAL INFORMATION

-3-

General Information

Safety Precautions

*Read these instructions carefully before commissioning the camera in order to

avoid damages caused by improper installation or use.

*Installation may only be carried out by authorised personnel according to the local

safety regulations.

*Operate the camera with the designated voltage only.

*Follow the safety instructions attached to the camera.

*Never use the camera for other purposes than designated.

*Repairs and adjustments at the camera may only be carried out by authorised

personnel.

*In case of ourdoor use you have to install the camera in a suitable weather

protection case incl. heating element.

*If any liquid or solid matter should get into the housing, disconnect the camera

from power supply and have it checked by your authorised dealer before re-using

(danger of electronic shock!).

*Do not disassemble the camera. To avoid electric shocks, never remove screws or

covers. There are no user-serviceable parts inside it. All maintenance may only be

carried out by authorised personnel according to the local safety regulations.

Install the camera by a least height of 2.30 m.

Composition

1. Auto Iris Lens Plug

2. Remote Plug

3. L-Wrench

4. C-Mount Adapter

5. Instruction Manual

MOUNTING THE CAMERA

-4-

Mounting the Camera

Mounting the Camera to a Wall Mount

COMMISSIONING THE CAMERA

-5-

Commissioning the Camera

Tips for Camera Location

1.0 To avoid internal overheating:

-never expose the camera to direct sunlight without additional camera housing

-keep sufficient distance to direct heat sources.

2.0 Never install the camera at humid, oily or dusty locations without using an

additional housing. (without additional housing the camera is not suitable for

outdoor use!)

3.0 The camera should be installed out of reach (min. height: 2.30 m)

4.0Do not aim the camera towards indoor lighting, the windows, the sunlight or the

sky (to get good pictures, camera and light should be aimed towards the object)

5.0 Reduce the picture detail to the

essential parts of the picture and place

the camera as close as possible to the

object (a smaller picture detail

guarantees sharper details).

6.0 Do not aim the camera towards a

window but instead towards the room.

7.0 Outdoors the camera should be

placed as high as possible so that the

horizon does not appear in the picture.

8.0 Avoid peak light as background (also

caused by reflections, e.g. window

panes).

wrong right

COMMISSIONING THE CAMERA

-6-

Adjustment of Back Focus

This adjustment should only be carried out, if the lens cannot be focused properly

using the lens focus ring. For such a case proceed as follows:

1 Loosen the Allan head screw with the

attached Allan head key. For large distances,

turn the focus ring of the lens almost (0.5 cm)

to the "endless" limit position. If you need to

focus an object near the camera, turn the

focus ring of the lens to a position 1cm before

the "near" limit position.

2 Use the back focus adjustment screw to adjust the distance between lens and

CCD chip until the picture is in focus. Then fix the Allan head screw using the Allan

head key.

3 Finally, focus the picture using the lens focus ring.

Adjustment of ES / DC Lenses

To adjust a lens with automatic iris (DC driven or video driven) to the camera, please

proceed as follows:

1. Turn the level potentiometer (position: ES lenses at the lens itself, DC lenses: at

the camera) to the max. position H (turn right). The monitor picture then

appears to be too bright.

2. Slowly turn the level potentiometer back until the monitor picture appears to be

perfect and is not too bright anymore. Then turn the potentiometer back to the

right (in direction "H") just a little bit.

3. Check the lens performance by using the camera under different and/or changing

light conditions.

Locking screws

COMMISSIONING THE CAMERA

-7-

Focusing the Camera Lens

After you have selected the correct picture detail you have to adjust the lens focus.

The focus adjustment needs to be done with the iris fully open, since the camera has

the smallest depth of focus in this position. If the focus adjustment was not done with

the iris completely open, the picture would be sharp during the day but slowly getting

out of focus the more the light disappears. To fully open the lens, use a grey filter in

front of the lens, provided you are using a lens with automatic iris. Adjust the focus

while the iris is fully open using the lens focus ring. Make sure the most important

picture details are in optimum focus (use a service monitor). If it is not possible to

bring the picture into focus, please adjust the back focus of the camera as described

above.

If you intend to use I.R. illumination at a later stage, you must use an I.R. pass filter

together with the grey filter during focus adjustment to ensure that only I.R. light will

get through to the camera chip and the focus adjustment is done according to this

spectrum, only. Attention: I.R. light can only be used in combination with mono

cameras, not colour cameras!

COMMISSIONING THE CAMERA

-8-

Circuit points and operation

ttention:

This camera comes with a four times electronic zoom. With the buttons Ý(Tele) and

ß(Wide) you can operate the zoom function. With activated WDR function the

electronic zoom is not possible!

1. Lens connector

2. Menu buttons

DC - Lens

1. Controll -

2. Controll +

3. Drive+

4. Masse

COMMISSIONING THE CAMERA

-9-

Rear View

Remote Jack

PC Interface

Belegung:

1. Frame GND

2. RD

3. TD

4. DTR

5. Signal GND

6. DSR

7. RTS

8. CTS

9. RI

RS 232/ RS 485 Converter

RS 232C PC Connector

Control

V-Phase

ELC

V-Phase

Control

AC 24V/ DC12V FG

Rear View IX 4000H Rear View IX 4000L

1. Auto Shutter / DC Lens

2. LL Phasen adjust

3. Control (Remote) Connector

4. Video Out

5. Power input

COMMISSIONING THE CAMERA

-10-

Camera Configuration

Menu:

CAMERA ID 000 ~ 255

ZONE LABEL SET

NEGA/POSI POSITIV / NEGATIV

SHARPNESS 0 ~ 15

MIRROR NORMAL, MIRROR, VERTIKAL, ROTATE

FREEZE ON, OFF

INITIAL ON, OFF

GENERAL

EXIT

WB MODE AUTO, HOLD, USER

RED CONT NOT USE (AUTO, HOLD), 1 ~ 255 USER

BLUE CONT NOT USE (AUTO, HOLD), 1 ~ 255 USER

PUSH AUTO NOT USE (AUTO, USER), OFF PUSH (HOLD)

INITIAL ON, OFF

AWB

EXIT

BRIGHTNESS 0 ~ 60

FLICKERLESS ON (PAL 1/100, NTSC 1/120)

SHUTTER SPD 1/250,1/500,1/1000,/1/2000,1/4000,1/10000

AGC MAX SET AGC OFF, LOW, MID, HIGH

MAX FLD SET OFF,2~20FLD,40FLD,80FLD,160FLD

INITIAL ON, OFF

EXIT

D/N MODE AUTO, DAY, NIGHT, EXT

LEVEL 0 ~ 200

FILTER DLY 0 ~ 15 SEC

INITIAL ON, OFF

D&N

EXIT

WDR MODE ON, OFF

WDR LEVEL 0 ~ 15

BACK LIGHT ON, OFF

BLC LEVEL 0 ~15

INITIAL ON, OFF

WDR

EXIT

AREA 1 ~ 4

MASK ON, OFF

START X

END X

START Y

END Y

INITIAL ON, OFF

PRIVACY

EXIT

CAMERA ID ON, OFF

ZONE LABEL ON, OFF

VERSION

DISPLAY

INITIAL ON, OFF

INITIAL OFF STATE

EXIT

This manual suits for next models

Table of contents

Other Vicon Security Camera manuals

Vicon

Vicon V960D-W Series Instruction manual

Vicon

Vicon Roughneck V894CSHR-VF-C User manual

Vicon

Vicon V930D User manual

Vicon

Vicon Roughneck Pro V2000D Series User manual

Vicon

Vicon Surveyor 282-20-02 Series User manual

Vicon

Vicon SVFT-C22 User manual

Vicon

Vicon CE202D-N User manual

Vicon

Vicon surveyor 2000 XX004 Operating instructions

Vicon

Vicon VC565DN User manual

Vicon

Vicon Surveyor MKII Series XX282-40-01 Quick guide

Vicon

Vicon Cruiser SN673V-B User manual

Vicon

Vicon ROUGHNECK V910 User manual

Vicon

Vicon V9360-1 User manual

Vicon

Vicon V1020-WIR-180 User manual

Vicon

Vicon Roughneck AI V2000D Series User manual

Vicon

Vicon Roughneck AI V2000 Series User manual

Vicon

Vicon VC275-24 User guide

Vicon

Vicon V980D Series User manual

Vicon

Vicon VC600 User manual

Vicon

Vicon Roughneck V926 User manual

Vicon

Vicon V2000D-W28IRM User manual

Vicon

Vicon VC367DSP User manual

Vicon

Vicon V922B-W551MIR-A1 User manual

Vicon

Vicon V662V-2 Series Operating instructions

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide