Vicon HPOE-100 User manual

Table of contents

Other Vicon Security Camera manuals

Vicon

Vicon V960D Series User manual

Vicon

Vicon VC455-DSP User manual

Vicon

Vicon V898MSH User guide

Vicon

Vicon V661-N-1 Series Operating instructions

Vicon

Vicon V662-D Operating instructions

Vicon

Vicon Cruiser SN673V-C User manual

Vicon

Vicon CRUISER S660V Operating instructions

Vicon

Vicon SURVEYOR 2000 S2000-CC22-EX User manual

Vicon

Vicon VC367DSP User manual

Vicon

Vicon Roughneck V920D Series Installation and operating instructions

Vicon

Vicon V992-N User manual

Vicon

Vicon V992B-IR4 User manual

Vicon

Vicon V-CELL-HD User manual

Vicon

Vicon surveyor1000 Owner's manual

Vicon

Vicon V662-D-1 Operating instructions

Vicon

Vicon V1008-WIR-180 User manual

Vicon

Vicon Roughneck V920D Series User manual

Vicon

Vicon V9360-6 Series User manual

Vicon

Vicon V930D User manual

Vicon

Vicon XX075-10 User manual

Vicon

Vicon SN118C User manual

Vicon

Vicon V661D-312IR Operating instructions

Vicon

Vicon VC2650-DSP User manual

Vicon

Vicon SVR-C User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide

HPOE-100

Network Camera Housing

INSTALLATION GUIDE

1.

Mounting Configuration and Dimensions

2.

Component Description

1

January 2016

3.

Power Consumption

D-Fog Heater

Always On (9W)

Heater

15°C On, 25°C Off (10W)

IR LEDs

3W

4.

Installation Recommendations

If you plan to install this camera enclosure into a tropical, sea coastal, or an environment where salt

water or corrosive industrial waste water/moist are present, please seal each stainless steel screws

and fittings with a silicon grease compounds. This will help prevent electrolysis to occur and extend

the life span of the camera and housing.

5.

Installation

A.

Prepare a CAT5e Ethernet cable. Pass it through the waterproofconnectors.

B.

You may need to remove the RJ45 connector, and use a crimping tool to connect the

Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable ofthe

width of 5 ~ 6.5mm.

2

January 2016

C.

When done, tighten up the waterproof connectors.

D.

Align the buffer pad with the mounting hole at the bottom of the camera

E.

Place the mounting plate on top of buffer pad and then secure it to the camera. You may need

adjust its position so that the lens module can flush align with the tempered glass.

F.

Secure the camera to the enclosure by securing screws through the keyholeslots.

3

January 2016

G.

Connect PoE input to the power unit. Connect a short Ethernet cable between thePoE

output and the Ethernet port on the camera. If using the media converter, connect the

wires to the 12V output on the PSU unit.

H.

Connect the day/night signal lines from the IR unit to the relay connectors on the

camera's terminal block. The day/night mode relay connection enables the

synchronization of IR light and the automated day/night switching mechanism onthe

camera.

I.

Having the wiring done inside the enclosure, you can install the enclosure bracket to a

preferred location at your installation site. Drill mounting holes and a cable routing hole(if

preferred) on a wall. Install the bracket.

J.

Lift the whole enclosure up to the installation position, and pass the Ethernetcable

through the bracket.

PoEINfrom

external

PoEOUTto

12VDCOUT

12Vpowertothe

4

K.

Mount the enclosure on to the installed bracket, and secure the connection bytightening

the 4 socket screws. Due to the weight of the enclosure, it is best to have two men

mounting the enclosure.

January 2016

5

Vicon Industries Ltd

www.vicon-security.com

6

January 2016